Restorer32 Posted September 19, 2019 Share Posted September 19, 2019 Last evening I watched an episode of a popular collector car show. The host described himself as having a life long interest in early cars. He was speaking to a crowd of 1500+ and was describing Brass Era cars. He stated, and this is not an exact quote, " Brass Era cars are called that because the headlights and other trim pieces were brass plated over the metal to prevent rust. Then came the Nickel Era when the brass was plated with nickel. Finally chrome was introduced to protect the nickel ". As far as I know few, if any, parts on Brass Ear cars were brass plated steel. Also, I believe nickel cannot be plated over brass very successfully. He did get the chrome over nickel thing right. Sadly this person helps judge many Concour events. Better if he had just said "Brass trim pieces were nickel plated in later years 3 Link to comment Share on other sites More sharing options...
JV Puleo Posted September 19, 2019 Share Posted September 19, 2019 (edited) The only brass plating I've ever seen on a "Brass Era" car is on the shifter & brake lever of my 1910 Mitchell. Actually, all that remains is the plating on the inside of the brake lever ratchet but, because the car is unrestored, I can be sure it was there when new. Brass was used for lights and radiator shells because it is easily shaped with the tools available at the time and was readily available. So, your show host doesn't know what they are talking about - which is hardly surprising. I stopped watching television at least 20 years ago, Oh...and even then brass was relatively expensive so as new machines were developed to work sheet metal it was replaced with much cheaper steel. The steel was either painted or nickel plated. Nickel plating was developed in Boston in the early 1870s and, at the time, experimented with as an "anti-rust" coating by the Ordnance Department which bought some nickel plated No.3 Smith & Wesson revolvers and had about 100 Trapdoor Springfield rifles plated. It was available before the advent of the automobile and was used on some early car parts. Hiram Percy Maxim had some of the engine parts of his first experimental tricycle, built in the early 1890s, nickel plated. I don't think nickel would stand the heat generated by a carbide light so it wasn't used for lights until electric lights were available. Brass lights were a PIA even then...unless you had a chauffeur to polish them. They sold special black heat paint for them so you wouldn't have to polish them. There is no problem nickel plating brass - it just wasn't done very often, The trick of getting nickel to stick to steel, which it didn't do very well, was to flash the piece with copper. This wasn't discovered until later so the plating peels off those early S&W's and Springfield rifles. One of the ways you can date early plated guns – or tell if they have been mucked with – with is to look for traces of the copper flashing since very few fakers know it wasn't done in period. Edited September 19, 2019 by JV Puleo syntax (see edit history) 3 1 Link to comment Share on other sites More sharing options...
trimacar Posted September 19, 2019 Share Posted September 19, 2019 The wealth of information that an expert can share, much of it incorrect, always amazes me. The reason so many parts on early cars were solid brass is that they couldn't form the complicated shapes out of steel. Everything else on an early car is flat or curved or cast, no compound curves. Is that true? I don't know, I just made it up..... 5 2 2 Link to comment Share on other sites More sharing options...
JV Puleo Posted September 19, 2019 Share Posted September 19, 2019 50 minutes ago, trimacar said: The wealth of information that an expert can share, much of it incorrect, always amazes me. The reason so many parts on early cars were solid brass is that they couldn't form the complicated shapes out of steel. Everything else on an early car is flat or curved or cast, no compound curves. Is that true? I don't know, I just made it up..... Yes, to a large extent. The huge presses and dies that were needed to make things like fenders and curved body panels developed over time and were extremely expensive to build. The technology to make them existed early on but the capitol investment to build such a machine was beyond almost all early car makers (who were almost always under capitalized). Many of the steel parts that were made early on, like pressed steel chassis rails, came from specialist manufacturers rather than the auto industry. We were probably into the 1920s or even 30s before car makers were selling enough to make the investment in the appropriate machines. I'll add that this is why making parts for brass cars is, in many ways, easier than making them for later cars. The machines and materials they had to work with were fairly limited which gives us a shot at replicating the parts where elaborate hydraulic presses the size of a house or sophisticated die casting equipment is impossible to find even if we had the time, money and space to make use of it. Link to comment Share on other sites More sharing options...
46 woodie Posted September 19, 2019 Share Posted September 19, 2019 Sometimes, when I'm at a car show with my '46 Ford "Woodie", I just stand to the side and listen to the "experts" tell the people they are with, all about station wagons. Many tell their audience that the bodies are made from oak, which we know is not correct, it's maple. They made the bodies out of wood because of steel shortages during the war. Well, what about all the wood bodies made between 1928 and 1941, before the war years? They stopped making them for safety reasons, really? The best I heard is when one guy told the lady he was with that they stopped making "Woodies" because they made so many, that they literally ran out of wood! I guess some people like to impress people and say anything that they think will impress people. 6 4 Link to comment Share on other sites More sharing options...
Restorer32 Posted September 19, 2019 Author Share Posted September 19, 2019 I heard a guy telling his buddy that the priming cups on an early car we were showing were "compression releases". He explained how you open the valves, get the engine spinning over then close the valves quickly and turn on the ignition. 1 3 Link to comment Share on other sites More sharing options...
mercer09 Posted September 19, 2019 Share Posted September 19, 2019 my 07Maxwell has nickel over the brass- was told people did this early on, so as not to have to polish the brass. sounds logical Link to comment Share on other sites More sharing options...
trimacar Posted September 19, 2019 Share Posted September 19, 2019 The best comment I ever heard at a show was a fellow walking by my '38 Packard with his son. "Look, son, a Packard, the only European car made in the United States...." 2 2 Link to comment Share on other sites More sharing options...
The 55er Posted September 19, 2019 Share Posted September 19, 2019 Once back in the day I had my Hudson stepdown parked on my space at Carlisle. A lead guy who was an old car expert walked by with two followers in tow. The expert pointed at my car and said "Look, there's an old Mercury." One of the followers commented that the car said Hudson on it. He replied "Yeah, well, Hudsons, they were made by Mercury". So much for historical accuracy. 1 2 Link to comment Share on other sites More sharing options...
W_Higgins Posted September 19, 2019 Share Posted September 19, 2019 Brass plated steel parts, as well as nickel plated parts, were very much a thing early on. Autocar (automobiles) offered nickel plating as an extra cost option, as did other manufacturers. On higher end cars it was an option or standard. Stanley was an early user of nickel lamps. Also, many parts were brass plated steel and the commonality you see on such parts is they tended to do it with things that rub where paint wouldn't last any time at all, like shift quadrants, linkages, and engine cranks. When you find an early car that hasn't been restored or was done once a long time ago it is not hard to find traces of the plating. It wasn't purely decorative. As to brass plated steel, many parts on Model T Fords up to mid-1911 were finished as such until they started to further cut costs and started enameling things. Many of the brass bolts and screws that are sold as solid brass reproductions today were originally brass plated steel, and for good reason if they are things that take a load, such as steering column-to-firewall bolts. On a 1911 Torpedo one of the cowl lamp bracket bolts is shared with a bracket that holds the cowl to the firewall. The solid brass bolts used in place of a steel one will shear after the body twists on it for awhile. Also, brass clad steel is often overlooked. Many cars used steel windshield support rods clad in brass that today people remake out of solid brass tube and if your car sees rough service they don't hold up so well. The people that designed these things weren't idiots and replacing steel parts with solid brass often spells trouble. 2 Link to comment Share on other sites More sharing options...
8E45E Posted September 19, 2019 Share Posted September 19, 2019 At the Lemay Museum in Marymount, the 'expert' guide tried to say 'the Gremlin was derived from the Hornet station wagon', which is incorrect, as the Sportabout was introduced in the fall of 1970, some five months after the Gremlin was release on April 1st of that year. And he tried to tell the group the 1957-59 Skyliner was 'Ford's "only" retractable hardtop'. I again told him afterward, Ford sold a version of the Focus (Focus 'CC') in Europe which was also a retractable hardtop. Craig Link to comment Share on other sites More sharing options...
Mark Wetherbee Posted September 19, 2019 Share Posted September 19, 2019 My definition of an expert is: “one who knows more and more about less and less until he knows absolutely everything about positively nothing” 5 2 Link to comment Share on other sites More sharing options...
Matt Harwood Posted September 19, 2019 Share Posted September 19, 2019 Surely there are no experts here, right? 2 1 Link to comment Share on other sites More sharing options...
1937hd45 Posted September 19, 2019 Share Posted September 19, 2019 8 hours ago, Restorer32 said: Last evening I watched an episode of a popular collector car show. The host described himself as having a life long interest in early cars. He was speaking to a crowd of 1500+ and was describing Brass Era cars. He stated, and this is not an exact quote, " Brass Era cars are called that because the headlights and other trim pieces were brass plated over the metal to prevent rust. Then came the Nickel Era when the brass was plated with nickel. Finally chrome was introduced to protect the nickel ". As far as I know few, if any, parts on Brass Ear cars were brass plated steel. Also, I believe nickel cannot be plated over brass very successfully. He did get the chrome over nickel thing right. Sadly this person helps judge many Concour events. Better if he had just said "Brass trim pieces were nickel plated in later years Why defend the expert, who is he? Burnout and donut driver no doubt. Bob Link to comment Share on other sites More sharing options...
Restorer32 Posted September 19, 2019 Author Share Posted September 19, 2019 Let's just say he is one of those guys who spends his time "pursuing high quality cars". Link to comment Share on other sites More sharing options...
60FlatTop Posted September 19, 2019 Share Posted September 19, 2019 6 hours ago, 46 woodie said: They stopped making them for safety reasons, really? That one is sort of true. The EPA clamped down on the because of the interstate transportation of wood and the potential of shipping invasive species of insects. That's a little gnawn fact. 1 Link to comment Share on other sites More sharing options...
60FlatTop Posted September 19, 2019 Share Posted September 19, 2019 3 hours ago, trimacar said: The best comment I ever heard at a show was a fellow walking by my '38 Packard with his son. "Look, son, a Packard, the only European car made in the United States...." I'd say he got that mixed up with the Packard Predictor. Along that line, in December 1954, there was a big Christmas party at the Altman & Newman Packard dealership in Southbend. The new V8 was out and Packard was ready to regain it's place in the prestige auto world. A man came in the door offering a new European car franchise. "Oh, go away with that funny little Volkswagen, don't you see the V8 signs? Our future is secure!" By the way, has anyone seen the new Fiat 124 Spyder? It has a familiar look. Link to comment Share on other sites More sharing options...
PFitz Posted September 19, 2019 Share Posted September 19, 2019 (edited) I can't speak to what was common on brass era cars,..... but many wood and coal stoves from as early as before 1900 used a lot of nickel plating. It was plated directly onto cast iron and steel parts that got VERY hot. And, there was no other type plating, such as copper, used as a subsurface. The nickel plates very well onto cast iron and steel that it doesn't need it. I collect antique stoves. Two that I use all Winter are a 1903 kitchen range and a 1908 parlor stove - both with lots of nickel trim that is very close to the firebed that often has the cast iron glowing red. I have a friend that used a 1879 Glenwood wood-burning kitchen range with nickel plated trim rails on the shelves, cooktop, and the oven door medallion. And the steel hand tools to tend the fire, such as fire pokers and cooktop lid lifters were nickel plated right over bare steel. It holds up very well even being used with such high heat. So well that many people mistake the original nickel on antique stoves for chrome plating. So the technology for plating nickel directly onto steel was common as early as the later part of the 1800's , even if the early auto industry didn't use it much. Paul Edited September 19, 2019 by PFitz (see edit history) 3 Link to comment Share on other sites More sharing options...
8E45E Posted September 19, 2019 Share Posted September 19, 2019 3 hours ago, trimacar said: The best comment I ever heard at a show was a fellow walking by my '38 Packard with his son. "Look, son, a Packard, the only European car made in the United States...." Pure speculation, but I wonder if he confused marques with the Springfield Rolls Royce. Besides American Austin, they would have been the only two foreign cars that were assembled in USA in the 1930's, though a few of the more expensive continental European cars may have been shipped 'chassis only' for an American coachbuilder to make a body for. Craig Link to comment Share on other sites More sharing options...
Locomobile Posted September 19, 2019 Share Posted September 19, 2019 In the parts that I have experience with 1899-1910ish, I've never seen any brass plated steel parts. I've seen nickel plated steel parts that are copper plated first, then nickel over brass is very common. Showing a steam car, I overhear conspiracy experts at shows comment that these cars run on water and the oil companies banded together and put them out of business etc. Oil companies would love the steam car with their 5-10 mpg. I just act busy with something else. -Ron Link to comment Share on other sites More sharing options...
wayne sheldon Posted September 20, 2019 Share Posted September 20, 2019 An "ex" is someone that used to be someone. A "spurt" is a small amount of water or other liquid, like a drop or "drip", under pressure. Therefore, an "expert" is a drip who used to be someone now under pressure. A couple details. 1909 into early 1911 model T fords had the brake handle and the hand crank brass plated. The first almost a thousand model Ts also had the reverse lever brass plated. These in addition to many bolts , brackets, and miscellaneous hardware. The early 1915 year model Ts had brass plated spark and throttle levers as well as the new design pressed steel quadrant were brass plated. Consider also. Somewhat before Ford's model T, there was another American automobile manufacturer that achieved status as the largest automobile manufacturer in the world. Before Ford's model T, another manufacturer began a form of assembly line production producing just a bit short of thirty thousand automobiles (if I recall the numbers correctly?) in approximately five years time! That manufacturer was Oldsmobile, with their Curved Dash and French Front models! And they used a considerable amount of nickel plating on most of those cars. I suspect that prior to about 1903, more cars had nickel plating than cars that did not. Stanley, Locomobile steam as well as numerous copycat cars that "infringed" or paid royalties to Locomobile, as well as quite a few electrics I know used nickel plating in the early years. I have over the years read of several early gasoline cars that offered nickel plating as an option, but I am not certain enough of the specifics to name any. I almost never watch any of the made-for-cable collector car tv shows. Bad enough they keep trying to cram muscle cars, hot rods, cruisers, and fantasy racing monsters down my throat. Fifteen minutes is about all I can stand to hear those guys talk in a month! 2 1 Link to comment Share on other sites More sharing options...
41 Su8 Posted September 20, 2019 Share Posted September 20, 2019 Supposedly, one of the causes of the demise of the steam car was the outbreak of Glanders and Hoof and Mouth Diseases in the late teens. Steam cars could get water in the rural areas by drafting water from a stream. In cities the cars would get their water from horse troughs. Due to the spread of these diseases, most of the cities removed the troughs, thus removing the source of water for steam cars. Sounds logical. John Link to comment Share on other sites More sharing options...
trimacar Posted September 20, 2019 Share Posted September 20, 2019 If you look at any TOC (turn of century, 1900) bicycle, you'll notice plenty of nickel plating. Even the little lights they used, while made of brass, were plated. Link to comment Share on other sites More sharing options...
Terry Bond Posted September 20, 2019 Share Posted September 20, 2019 Regarding brass plated steel on early cars, the Model T Ford used some brass plated items on their early cars - some fasteners as well as the ends of the throttle and spark control levers. l believe there were also early cars that used brass plated steel control levers. A local friend restored a 1908 Maxwell several years ago and the outside shift lever was brass plated steel. I have a few early accessory catalogs including two from Solar Lamp company, and lamps could be purchased in polished brass, nickle plate or black enamel. They were all brass underneath. Terry Link to comment Share on other sites More sharing options...
Restorer32 Posted September 20, 2019 Author Share Posted September 20, 2019 Packard headlights were chrome plated brass at least thru 1934. 1 Link to comment Share on other sites More sharing options...
Mark Shaw Posted September 20, 2019 Share Posted September 20, 2019 19 hours ago, W_Higgins said: The people that designed these things weren't idiots and replacing steel parts with solid brass often spells trouble. I agree, but castings made from Silica Bronze are much stronger, & look like solid brass. Local club members and I have used a local foundry to cast silica bronze for windshield supports, shift levers, and other high stress components (see below). Silicon Bronze Silicon Bronze is a high-strength, highly corrosion resistant material with nonmagnetic properties. It is generally as strong as steel. Because of its composition, it is more difficult to machine. However, it is excellent for use in general marine applications, as well as pumps, heavy equipment, fittings, and boilers. Silicon Bronze, C655 Minimum Properties Ultimate Tensile Strength, psi 85,000 Yield Strength, psi 55,000 Elongation in 2" 20% Rockwell Hardness B90 Chemistry Copper (Cu) 97.0% min Iron (Fe) 0.8% max Manganese (Mn) 1.5% max Nickel (Ni) 0.6% max Lead (Pb) 0.5% max Silicon (Si) 2.8 - 3.8% Zinc (Zn) 1.5% max Alcobra Metals states that all technical data is for comparison purposes only and is NOT FOR DESIGN. It has been compiled from sources we believe to be accurate but cannot guarantee. Please consult an Engineer. Copied from: https://alcobrametals.com/guides/bronze 1 Link to comment Share on other sites More sharing options...
W_Higgins Posted September 20, 2019 Share Posted September 20, 2019 1 hour ago, Mark Shaw said: I agree, but castings made from Silica Bronze are much stronger, & look like solid brass. Local club members and I have used a local foundry to cast silica bronze for windshield supports, shift levers, and other high stress components (see below). Silica Bronze is good stuff and certainly has it's place, but it's apples-and-oranges with respect to my original comment regarding the substitution of solid brass parts for parts that were formerly brass plated steel. That aside, polished silica bronze looks like polished silica bronze to me. On cars that sport both polished bronze and brass hardware, the contrast is clear. Link to comment Share on other sites More sharing options...
oldford Posted September 21, 2019 Share Posted September 21, 2019 On the subject of misinformation from experts... Back in the 70's, we were on a short tour up through the Catskill Mountains with some family members and my brother was driving is Morgan +4. As we were leaving the breakfast spot, I overheard a young boy ask his father about the marque Morgan. His father replied that it was a Morgan made by it's parent company MG which stood for Morgan Garages... I l learned something new that day.... Frank Link to comment Share on other sites More sharing options...
Restorer32 Posted September 21, 2019 Author Share Posted September 21, 2019 I was once told that MG was French and stood for Morris Gararga. Link to comment Share on other sites More sharing options...
padgett Posted September 21, 2019 Share Posted September 21, 2019 And then there is (warning political content) how Swallow Sidecars became Jaguar because "SS" had bad connotations. Fun (but nothing to do with brass other than an attitude) is how names have changed for different reasons: Russian dressing Dolphin Patagonian toothfish Idlewild Maybe we need a banter thread... Link to comment Share on other sites More sharing options...
John_Mereness Posted September 22, 2019 Share Posted September 22, 2019 We have brass plated the brass (on a whole car excepting the radiator shell) - the need came due to various different metals used matched to impurities in the metal and plenty of abuse/time, plus and unfortunately we believed the car would score low in AACA judging as a result. The good news is that brass plated brass holds up longer in finish and really did look stunning. Link to comment Share on other sites More sharing options...
60FlatTop Posted September 22, 2019 Share Posted September 22, 2019 20 hours ago, padgett said: Swallow Sidecars became Jaguar because "SS" had bad connotations I think that should be Super Swallow. Just to be historically accurate. 1 Link to comment Share on other sites More sharing options...
1937hd45 Posted September 22, 2019 Share Posted September 22, 2019 KRIT went out of business long before 1933. Bob Link to comment Share on other sites More sharing options...
padgett Posted September 23, 2019 Share Posted September 23, 2019 https://en.wikipedia.org/wiki/Swallow_Sidecar_Company Link to comment Share on other sites More sharing options...
8E45E Posted September 23, 2019 Share Posted September 23, 2019 On 9/21/2019 at 12:22 PM, padgett said: And then there is (warning political content) how Swallow Sidecars became Jaguar because "SS" had bad connotations. In the 1930's Studebaker was forced to change their model name, 'Dictator' to 'Director' in certain markets. And Chevrolet's use of the 'SS' also had some backlash in 2014: https://www.foxnews.com/auto/chevrolet-ss-model-criticized-in-israel-for-evoking-name-of-nazi-organization Had GM chose to market the 'SS' in Israel, it no doubt would have been sold under a different name. Craig Link to comment Share on other sites More sharing options...
1937hd45 Posted September 23, 2019 Share Posted September 23, 2019 (edited) Did the 1932 Chevrolet Confederate Coupe sell better in the south? Edited September 23, 2019 by 1937hd45 (see edit history) Link to comment Share on other sites More sharing options...
8E45E Posted September 23, 2019 Share Posted September 23, 2019 8 hours ago, 1937hd45 said: Did the 1932 Chevrolet Confederate Coupe sell better in the south? Makes one wonder. Did early Dodges sell better in Israel because of the 'Double-Delta' on the radiator badge? Craig Link to comment Share on other sites More sharing options...
padgett Posted September 23, 2019 Share Posted September 23, 2019 Allard "Palm Beach", Mustang "California Special", Citroen "Sahara". Link to comment Share on other sites More sharing options...
JV Puleo Posted September 23, 2019 Share Posted September 23, 2019 (edited) They were probably rarely, if ever, seen. When the Dodge car appeared, what is now Israel was part of the Ottoman Empire. After WWI it was governed by Britain under a League of Nations mandate. How many Dodge cars might have been imported is an interesting question but the US Army, which used a lot of them in France, never had any units in the Middle East during the war so they wouldn't have been seen through that source. Israel didn't become an independent country until 1947 when Palestine was partitioned by the United Nations. I do think it is possible that it helped the sale of Dodge cars in urban areas of the US where Henry Fords overt anti-Semitism turned a lot of people off - not only Jews. I have read - and don't have the citation at hand - that the anti-Semetic campaign almost wiped out the sale of Ford cars in cities with significant Jewish populations and that the largest single Ford dealer sent in his papers and became a Dodge Brothers dealer. It was apparently also a Ford thing to distribute copies of the Dearborn Independent (Ford's newspaper and the spearhead of the anti-Semitic campaign) to dealers with instruction they were to be handed out to customers. Many dealers paid for them and destroyed them rather than offend their customers. Edited September 23, 2019 by JV Puleo (see edit history) 1 Link to comment Share on other sites More sharing options...
60FlatTop Posted September 23, 2019 Share Posted September 23, 2019 14 hours ago, 8E45E said: nd Chevrolet's use of the 'SS' also had some backlash in 2014: https://www.foxnews.com/auto/chevrolet-ss-model-criticized-in-israel-for-evoking-name-of-nazi-organization Had GM chose to market the 'SS' in Israel, it no doubt would have been sold under a different name. It is interesting that the Fox news article has no byline other than Fox News. It was probably circulated through the office and the writers replied "I'm not putting my name on that stupid sensationalist crap. Who runs Fox now? He should put his name on anything they can't publish without a byline, in bold print. Reminds me, I have found a great way to maintain historical accuracy in current news. Any time a current news story brings in two or more reporters, editors, or other collaborators of the media occupation I switch the TV to reruns of Green Acres. And to other matters: https://en.wikipedia.org/wiki/SS_Cars Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now