John_Mereness Posted December 5, 2020 Share Posted December 5, 2020 On 12/3/2020 at 9:55 PM, 38Buick 80C said: I hadn't considered, that the hose may be collapsing, that said I would think: 1. it's not really under load and I've only experienced hose collapse under load where the water pump (in a modern V8) creates such a suction the hose collapses 2. with the drain tube thing I had "reproduced" (I mean I guessed at what it might be like based on photos of other cars) the rubber hose lengths on this car are pretty short all things considered. But I'm gonna be watching for that none the less now that you said something, if nothing but to cross it off the list of possibilities. Thanks for the reminder. Yes, you generally need acceleration to collapse a hose - idle will not do it (that is how people miss the issue). 1 1 Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 5, 2020 Author Share Posted December 5, 2020 (edited) Ok I started the car yesterday and she ran well, definitely could tell the proper timing made a difference. Today after soccer game I had a chance to do a test drive. Here is the edited video. You'll see I stalled out and edited it until I realized needed the electric fuel pump to help. Also later in the drive I realized the parking brake was still engaged. She did a burn out though... Also no overheating during the test drive. As you can see it wasn't a long drive and the ambient temp is cool so will have to check on this again. After the test drive I swapped her bay in the garage and installed the front bumper and test fit installed some of the wood grained trim Finally I messed around with the side-mount hardware to see how it installs. I took it back off after these photos cause a) I still need to get the correct size rubber grommet at the cowl and b) because I don't want the hardware or the tire in the way when the car goes in for buff. Tomorrow I need to sand two piece of wood grain to be re-done as the wrinkled during the clear coat. aside from that i need to take some pieces to some third party folks 1. some wood grained pieces to the pinstriper 2. the rope rail mounts to the machine shop to be honed and also gonna have the shop make some correct 7/16 counter sunk slotted screws for the gas tank cover 3. running board back to the wood shop to have some adjustments and drilling etc done. Edited December 5, 2020 by 38Buick 80C (see edit history) 10 Link to comment Share on other sites More sharing options...
John_Mereness Posted December 5, 2020 Share Posted December 5, 2020 (edited) Strikes me starting out as possible fuel delivery or needs to run more rich (or possibly timing as you mention) - you seem to be doing better in the home stretch. Edited December 5, 2020 by John_Mereness (see edit history) 1 Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 5, 2020 Author Share Posted December 5, 2020 (edited) 8 minutes ago, John_Mereness said: Strikes me starting out as possible fuel delivery or needs to run more rich (or possibly timing as you mention) - you seem to be doing better in the home stretch. well I think its a combo of 1. parking brake engaged 2. not much fuel in the tank so a pick up problem solved by running the electric pump 3. not warmed up enough. I need to experiment some more, but yes after the stall was much better. also need to learn how to tackle the un-synchronized shifting. I got to get that double clutch method down I guess. I did add 5 more gallons after this run. Edited December 5, 2020 by 38Buick 80C (see edit history) 1 Link to comment Share on other sites More sharing options...
Matt Harwood Posted December 5, 2020 Share Posted December 5, 2020 That's great news, Brian! Fine-tuning will take a while but for it to run that well right off the bat is very promising. 1 Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 6, 2020 Author Share Posted December 6, 2020 anyone have info on the vacuum system for the wiper, specifically what happens under dash? I have 1. the line from the intake through the firewall into the under dash 2. the 2 lines coming from the wiper over the header and down the passenger A-post to the under dash. 3. the "switch" with one port on one side and 2 on the other so one would assume a. line in item #1 goes to the one port side b. lines from the wiper go in the 2 port side (but which one in which port or does it matter and since the lines in #1 and #2 terminate nowhere close to the switch, I'm curious as to whether rubber tube or metal tube is used to connect them and routing, etc. photos would be an immense help. Thanks. Link to comment Share on other sites More sharing options...
CarNucopia Posted December 6, 2020 Share Posted December 6, 2020 24 minutes ago, 38Buick 80C said: anyone have info on the vacuum system for the wiper, specifically what happens under dash? I have 1. the line from the intake through the firewall into the under dash 2. the 2 lines coming from the wiper over the header and down the passenger A-post to the under dash. 3. the "switch" with one port on one side and 2 on the other so one would assume a. line in item #1 goes to the one port side b. lines from the wiper go in the 2 port side (but which one in which port or does it matter and since the lines in #1 and #2 terminate nowhere close to the switch, I'm curious as to whether rubber tube or metal tube is used to connect them and routing, etc. photos would be an immense help. Thanks. I’ll take a look at mine and let you know. 1 Link to comment Share on other sites More sharing options...
CarNucopia Posted December 6, 2020 Share Posted December 6, 2020 (edited) 4 hours ago, 38Buick 80C said: anyone have info on the vacuum system for the wiper, specifically what happens under dash? I have 1. the line from the intake through the firewall into the under dash 2. the 2 lines coming from the wiper over the header and down the passenger A-post to the under dash. 3. the "switch" with one port on one side and 2 on the other so one would assume a. line in item #1 goes to the one port side b. lines from the wiper go in the 2 port side (but which one in which port or does it matter and since the lines in #1 and #2 terminate nowhere close to the switch, I'm curious as to whether rubber tube or metal tube is used to connect them and routing, etc. photos would be an immense help. Thanks. It was hard to get good photos with the car under a cover. Hopefully this helps. If not, I should be able to do a better job in a day or so. The first photo is the under-dash side of the switch (the left side heads to the passenger side and the right to the driver). The tube on the right goes through the firewall in front of the driver (shown in the 2nd picture). The two tubes on the left are black, but feel like metal, and go to the A pillar base in front of the passenger (3rd photo). Edited December 6, 2020 by Car-Nicopia (see edit history) 1 1 Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 6, 2020 Author Share Posted December 6, 2020 7 hours ago, Car-Nicopia said: It was hard to get good photos with the car under a cover. Hopefully this helps. If not, I should be able to do a better job in a day or so. The first photo is the under-dash side of the switch (the left side heads to the passenger side and the right to the driver). The tube on the right goes through the firewall in front of the driver (shown in the 2nd picture). The two tubes on the left are black, but feel like metal, and go to the A pillar base in front of the passenger (3rd photo). perfect, this is what I needed. Of course mine is a bit different but I will figure it out. 2 Link to comment Share on other sites More sharing options...
old-tank Posted December 6, 2020 Share Posted December 6, 2020 15 hours ago, 38Buick 80C said: I got to get that double clutch method down I guess. Yep. It will become much easier with practice and then you will find that it behaves differently with cold vs hot tranny fluid. And eventually you will learn how to slip the gears without a clutch! 1 Link to comment Share on other sites More sharing options...
John_Mereness Posted December 6, 2020 Share Posted December 6, 2020 21 hours ago, 38Buick 80C said: well I think its a combo of 1. parking brake engaged 2. not much fuel in the tank so a pick up problem solved by running the electric pump 3. not warmed up enough. I need to experiment some more, but yes after the stall was much better. also need to learn how to tackle the un-synchronized shifting. I got to get that double clutch method down I guess. I did add 5 more gallons after this run. Some cars do not need double clutched, but not sure if this is one of those - the ones that do not need double clutched, do take confidence/certainty though. Link to comment Share on other sites More sharing options...
John_Mereness Posted December 6, 2020 Share Posted December 6, 2020 Will take a while to figure out its magic/sweet spots and timing for Clutch, Spark, Choke, & Throttle. Plus, someone above touched on such as gear oil. And there may need to be some pedal adjustment and other tinkering. Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 7, 2020 Author Share Posted December 7, 2020 Did a few minor things today. 1. Rechecked the valve lash 2. Re-routed the horn wiring harness properly through the fire wall 3. Installed one missing fender running board bracket And the biggest job of the day was working on the brake light, which I noticed wasn't coming on. Long story short is first I had a bad ground, solved that but have determined the stop light switch is not functioning. I did put in a nice bright LED for the stop light. I determined it wasn't working by and did the following diagnosis. 1. Bypassing it with a jumper wire (Which is how I determined the bad ground) 2. Disconnected the linkage and moved it manually, no joy 3. Swapped the wires on the switch and manually moved the linkage, no joy I believe I have a spare switch. I will have to see how it works and see if I can get it sorted out on the bench and then swap them. I did notice my tail light work in parking and bright setting, but not in dim setting, that seems incorrect but will have to research it. Hoping to get all the lighting sorted even though I don't have the headlights installed yet. 1 Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 8, 2020 Author Share Posted December 8, 2020 I have a spare light switch, but not a stop light switch. I disassembled and rebuilt/cleaned up the light switch for use, but guess I will have to remove and clean up the stop light switch that is on the car. Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 8, 2020 Author Share Posted December 8, 2020 sucess when I took apart the switch I found one of the internal leads had broken off. I devised a way to re-secure it in place and with that I have a working brake light. on to the light switch next... not tonight... And the Redskins or the WFT or WTF...whatever... they won too, awesome night... 1 1 Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 8, 2020 Author Share Posted December 8, 2020 OK silly question of the day. Should the clear lens be illuminated with the tail light or with the brake light? It would seem I could mount the internal guts for either, so...which is correct? Link to comment Share on other sites More sharing options...
MCHinson Posted December 8, 2020 Share Posted December 8, 2020 I have no experience with this era Buicks but I would say that the tail light should be red and the brake light would be the clear one. I would wonder if there was originally an amber insert to make the brake light illuminate yellow. Fords of the era have an almost identical taillight that has a red taillight and an amber brake light. Not that I think you would ever be stopped, but a white light illuminated on the rear of a vehicle while in forward motion is actually illegal in NC. Technically neither a taillight or brake light can illuminate white light in NC. Link to comment Share on other sites More sharing options...
John_Mereness Posted December 8, 2020 Share Posted December 8, 2020 4 hours ago, 38Buick 80C said: OK silly question of the day. Should the clear lens be illuminated with the tail light or with the brake light? It would seem I could mount the internal guts for either, so...which is correct? Neither - isn't the clear lens a reverse lamp ? 1 Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 8, 2020 Author Share Posted December 8, 2020 (edited) 2 hours ago, John_Mereness said: Neither - isn't the clear lens a reverse lamp ? not enough bulbs or wires for that. only 2 bulbs/wires in the system, brake light and tail light. and the tail light most definitely needs to be a white bulb as it illuminates the plate as well via a lens on the bottom of the housing. Edited December 8, 2020 by 38Buick 80C (see edit history) Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 8, 2020 Author Share Posted December 8, 2020 @Pete Phillips @Bill - 29 Buick Pete or Bill? would you know the answer on the question 6 hours ago, 38Buick 80C said: OK silly question of the day. Should the clear lens be illuminated with the tail light or with the brake light? It would seem I could mount the internal guts for either, so...which is correct? Link to comment Share on other sites More sharing options...
Erndog Posted December 9, 2020 Share Posted December 9, 2020 (edited) The 1930 Buicks did, in fact, have a back-up light that comes on when the transmission is shifted to reverse. There is a switch at the top rear of the transmission that is activated by a rod that pokes out when put in reverse.e Edited December 9, 2020 by Erndog (see edit history) 2 Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 9, 2020 Author Share Posted December 9, 2020 7 hours ago, Erndog said: The 1930 Buicks did, in fact, have a back-up light that comes on when the transmission is shifted to reverse. There is a switch at the top rear of the transmission that is activated by a rod that pokes out when put in reverse.e and we have an answer to the clear lens question as well in that case. Thanks 2 1 Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 9, 2020 Author Share Posted December 9, 2020 also found this topic on the subject 1 Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 10, 2020 Author Share Posted December 10, 2020 anyone have any detailed photos of what supposed to be going on inside the headlight assembly? i found this on ebay...not sure i understand this spring and rod up to the bulb housing? Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 10, 2020 Author Share Posted December 10, 2020 found a diagram in the reference manual and found one focus screw spring. I don't have an understanding of what I am looking for in the focus crew itself or whatever goes from the top of the screw to the bulb socket. Link to comment Share on other sites More sharing options...
Erndog Posted December 10, 2020 Share Posted December 10, 2020 I'll try to locate my headlights and take pictures tomorrow if no one beats me to it. 1 Link to comment Share on other sites More sharing options...
Erndog Posted December 10, 2020 Share Posted December 10, 2020 Found 'em. I am assuming you also have the reflectors that go with them. 2 1 Link to comment Share on other sites More sharing options...
Erndog Posted December 10, 2020 Share Posted December 10, 2020 This is for the 1929 cars, but I am sure it is the same for 1930. 1 Link to comment Share on other sites More sharing options...
Erndog Posted December 11, 2020 Share Posted December 11, 2020 A couple more. Just a screw with a teensy weensy cotter pin and the spring, then the socket mount. 3 Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 11, 2020 Author Share Posted December 11, 2020 thanks Ernie that helps a ton... Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 12, 2020 Author Share Posted December 12, 2020 (edited) Today's progress I'm quite pleased with I rebuilt a spare light switch and installed it. Now the tail light comes on for all settings. I also have the side light parking lights First one Then with a little rebuild and some better grounding (isn't that always it with these cars) both are now on I also filed out the hole for the map light and got that installed and functioning. I messed with the instrument panel lights some but not there yet. With a small adjustment and getting the wires in the rights spots I do have a reverse light (thanks all who pointed that out). Took her out for another spin. I went down and back up the BIG hill in the neighborhood this time and noted the following 1. I'm getting better at the double clutch footwork 2. The brake pedal was sticking some. I oiled all the pin joints and that seemed to help 3. I am shifting into 3rd too early on the hill, she sounds ready in 2nd and then in 3rd she's bogged down. 4. She's still overheating, mostly at idle. I got her up over 200 idling while oiling the brake cables and then went back around the neighborhood and she seemed to come down a hair and get back under 200, but then once I got back in the drive and was backing her into the garage she spiked right back up and started pissing some I adjusted the valves again at this point since she was good and hot. A bunch of them were too tight hot. that seemed to quiet her down considerably but still feel like I've got a little too much valve train noise. That also let me adjust the idle down a bunch and she's running MUCH smoother. I suppose I need to see if that helped with the overheating any but that seems a long shot. Probably will take her down the road to the gas station for some ethanol free tomorrow. Also this week I got the running boards back to the wood shop to do some more work that I don't have the tools to do myself. I hope to have that back next week so I can put those together and on the car. Took some items to the machine shop too that are just detail items I ran out of talent and tools on, maybe get those back soon too. I also placed a Bob's order for some side mirrors and a few other minor things (of course noticed a couple more things I need today). Need to get to the GOOD hardware store for some rubber grommets for the cowl at the side mount supports. Finally ordered a spare cheap headlight to try and get some of the inner components sorted out or at least have ones i can take pictures of so I can acquire them (without having to buy a whole assembly again) Edited December 12, 2020 by 38Buick 80C (see edit history) 6 Link to comment Share on other sites More sharing options...
Erndog Posted December 13, 2020 Share Posted December 13, 2020 Have you verified proper operation of the shutter thermostat? Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 13, 2020 Author Share Posted December 13, 2020 5 hours ago, Erndog said: Have you verified proper operation of the shutter thermostat? Well it seem to just kinda stay in one position...about 3/4 open. Thus open enough that I feel like air movement at idle with the fan is more than enough. Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 13, 2020 Author Share Posted December 13, 2020 Morning project while watching F1, disassembled, cleaned, rebuilt and adjusted the horn. No photos. Much clearer note now. 1 Link to comment Share on other sites More sharing options...
dei Posted December 13, 2020 Share Posted December 13, 2020 No matter the size of the project it's all about plugging away one step at a time isn't it. Baby steps and before you know it, you can see light at the end of the tunnel. That's been my learning curve this past year. Enjoying your journey with the car. 2 Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 13, 2020 Author Share Posted December 13, 2020 What's this fitting called? 1 Link to comment Share on other sites More sharing options...
38Buick 80C Posted December 13, 2020 Author Share Posted December 13, 2020 Started messing with the pilot ray light. Polished the chrome and it cleaned up nice. Here are all the parts laid out. Apperently I have to get some 5/16 rod. My question, see photo below. The mounting brackets seem like I'm missing something. The front edge (chrome part of mount is a flat edge, and then as you can see there are u shaped pieces that bolt to the chrome. This obviously go over the chassis round tube cross bar. The u brackets are a bit to large for the diameter and then with the flat front it seems like there should be something, possibly a rubber piece, that would get squashed during tightening and thus hold it all upright. Thoughts from those with experience? Link to comment Share on other sites More sharing options...
Erndog Posted December 13, 2020 Share Posted December 13, 2020 (edited) Compression fitting. Oil line? Similar to modern SwageLok fitting. Edited December 13, 2020 by Erndog (see edit history) 1 Link to comment Share on other sites More sharing options...
lancemb Posted December 14, 2020 Share Posted December 14, 2020 10 hours ago, 38Buick 80C said: What's this fitting called? I'm curious too. It's different than a standard compression fitting as is commonly found. My 57s use these at the oil gauge line and manifold vacuum lines, at least. I would like to have some new ones next time I need one. Link to comment Share on other sites More sharing options...
Erndog Posted December 14, 2020 Share Posted December 14, 2020 11 hours ago, lancemb said: I'm curious too. It's different than a standard compression fitting as is commonly found. My 57s use these at the oil gauge line and manifold vacuum lines, at least. I would like to have some new ones next time I need one. Should be able to find something here for it. However, looking more closely at one of mine, it looks like the bevel is built into the fitting and an insert may be in the end of the tubing. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now