John_Mereness Posted February 14, 2020 Share Posted February 14, 2020 That is GREAT ! I loved seeing your car at Cincinnati/Ault Park Concours d'Elegance ! Link to comment Share on other sites More sharing options...
frame30 Posted February 20, 2020 Share Posted February 20, 2020 On 1/11/2019 at 8:37 PM, 95Cardinal said: First step in assembling the front seat back was to clean, paint and inspect the seat frame and spring unit. The transverse spring wire that supports the individual zig-zag springs (essentially the lumbar support) was fractured and had to be replaced. This frame came from low-mileage car and was in excellent condition. The clean, shiny metal you see is as the frame appeared when the old trim cover was removed! It has been coated with a clear protectant to preserve it. Initial test fit of the trim cover and side panel to ensure that all the seams will be covered by the side panels as designed and sewn. I installed the 2 screws that will ultimately attach the ash tray to the seat back. Having the screw heads in place will make it much easier to locate the attaching points for the ash tray after the trim cover has been attached to the frame. Visible at the top of the above image is the first point of attachment of the seat cover. There is a wire-reinforced upper bolster that is attached via hog rings to the upper frame rail. The heavy felt isolator is installed between the two layers of springs in the seat back spring unit. The trim cover is drawn over the perimeter of the frame and retained with hog rings. After installing the cover and verifying the fit of the side panel, the upper bolster looks loose and baggy. The area beneath the french seam required additional padding to fill out the cover contours. I removed the cover and added thin layers of cotton/poly blend padding to better match the cover shape After re-installing the cover, fabricated stuffing tools like these make it easier to manipulate the last bits of padding into the necessary position under the corner: End view of the seat back after revising the corner padding. Front seat back, ready for assembly to the cushion: The 1958 Buick foam seat cushions were among the earliest applications of molded urethane foam seating components. The Special models retained the traditional spring and pad designs for the seat cushions and backs. The Century, Super, Roadmaster and Limited models were equipped with foam seat cushions, but retained "spring and pad" seat back pads with rubberized horsehair pads. I disassembled the seat frame and cleaned and painted the steel structure. Since the cushion frame had some surface corrosion, I used a more aggressive treatment and then painted the frame black. I inserted a stiff reinforcement layer of woven carpet material between the springs and the foam layer, hog-ringing the carpet to the zig-zag springs to ensure that the underlayment would not shift with occupant entry/egress. The carpet replaces the original layer of cotton burlap, which had long ago lost its ability to support the foam and isolate it from the springs. New foam is installed, along with a layer of non-woven cotton/poly felt to retain the rear edge of the foam to the frame. The felt also acts as an insulator/isolator between the rear section of the trim cover and the "bar cover", or rear bottom section of the frame. The foam is trimmed to shape and "skived" or contoured at the perimeter to give a smooth appearance of the cover after assembly. I have found that an electric carving knife works great for shaping and contouring the urethane foam. The pink chalk mark highlights the center of the frame and the center of the trim cover. I always start in the center and work outwards from the center to establish and maintain the proper cover position on the seat. Like the original design, I added a layer of padding and burlap above the foam, then applied the trim cover: The first step in retaining the cover was to hog ring the rear "tie-down" to the lower portion of the seat frame, just beneath where the forward edge of the seat back would eventually be positioned. Then, working out from the center, hog-ringing the perimeter of the cover to the frame. After building up the assembly, I determined that I needed additional padding to get the required comfort, fit and appearance. The cover was too loose on the pad assembly. I removed the cover from the frame and added a thin layer of padding over the entire seating surface, with additional layers around the perimeter to provide a more full looking perimeter. The second build-up was much improved Attaching the seat back to the cushion is accomplished with 6 - yes, 6! - 1/4-20 bolts. Adding the ash tray and robe cord to the seat back: It took 3 of us to maneuver the seat into the car, but we managed to position it without any injuries or damage: It will be challenging (impossible?) to install the seat side panels in the vehicle, but the side panels are still at the anodizer's facility. If necessary, the seat will be removed to allow installation of the aluminum trim panels. Dear Joe: Putting my front seat in next week I hope. As you know, most of my photos blew up in the computer. Does the front seat just bolt down or (as I have been told) there are two little channels that hold the front down. Confused. Any pictures of what they (if needed) might look like? Great series. I use your site a lot for my restoration. 49D wagon. Cheers from Alberta. Michael. Link to comment Share on other sites More sharing options...
frame30 Posted February 21, 2020 Share Posted February 21, 2020 Dear Joe: It would be three as I have the split rear seat same as you. Cheers. Michael. Link to comment Share on other sites More sharing options...
95Cardinal Posted February 21, 2020 Author Share Posted February 21, 2020 Frame30 wrote: "Dear Joe: Putting my front seat in next week I hope. As you know, most of my photos blew up in the computer. Does the front seat just bolt down or (as I have been told) there are two little channels that hold the front down. Confused. Any pictures of what they (if needed) might look like? Great series. I use your site a lot for my restoration. 49D wagon. Cheers from Alberta. Michael." Michael, Yes, there are 2 u-shaped brackets that mount to the floor pan and retain the front of the seat adjuster. They are the 2 pieces with 2 bolt clearance holes in this image: These brackets are approximately 1" wide, about 4" long and approx. 1" high. Hope this helps! Joe 2 Link to comment Share on other sites More sharing options...
frame30 Posted February 22, 2020 Share Posted February 22, 2020 4 hours ago, 95Cardinal said: Frame30 wrote: "Dear Joe: Putting my front seat in next week I hope. As you know, most of my photos blew up in the computer. Does the front seat just bolt down or (as I have been told) there are two little channels that hold the front down. Confused. Any pictures of what they (if needed) might look like? Great series. I use your site a lot for my restoration. 49D wagon. Cheers from Alberta. Michael." Michael, Yes, there are 2 u-shaped brackets that mount to the floor pan and retain the front of the seat adjuster. They are the 2 pieces with 2 bolt clearance holes in this image: These brackets are approximately 1" wide, about 4" long and approx. 1" high. Hope this helps! Joe Dear Joe: Thanks!! You wouldn't have to have two of these you would like to sell? Seems my seats were never properly seated. Cheers. Michael. Link to comment Share on other sites More sharing options...
95Cardinal Posted February 22, 2020 Author Share Posted February 22, 2020 I'll check this weekend and let you know. If I don't have any, Jim might have extras. Joe Link to comment Share on other sites More sharing options...
frame30 Posted February 24, 2020 Share Posted February 24, 2020 Dear Joe: Look forward to your search. My daughter, Kailla, and I searched (again) Sunday afternoon. Nothing. Cheers. Michael. Link to comment Share on other sites More sharing options...
95Cardinal Posted February 25, 2020 Author Share Posted February 25, 2020 19 hours ago, frame30 said: Dear Joe: Look forward to your search. My daughter, Kailla, and I searched (again) Sunday afternoon. Nothing. Cheers. Michael. Sending you a PM, Michael. 1 Link to comment Share on other sites More sharing options...
jherrera55buickcentury Posted May 18, 2020 Share Posted May 18, 2020 Hello I'm Juan. I have a 55 Buick Century. I am having problems adjusting the rear window. I already lined up the vent window and the passenger window. I just can’t seem to find where I can move this glass front to back just a zinch. If you recall on you project, any help will be appreciated. thank you. Link to comment Share on other sites More sharing options...
95Cardinal Posted May 18, 2020 Author Share Posted May 18, 2020 Hi Juan, If I remember correctly, front to back adjustment was accomplished by setting the wedges and travel stops at the both front and rear ends of the glass opening, at the very top of the door. Every adjustment seemed to have some interaction with other settings, so it tokk me a lot of trial and error to get it right. The Fisher Body Service Manual has detailed, step by step instructions for the removal of the window glass and all related parts. After lots of frustrating experimentation, I found that the best way to line up the windows was to follow the instructions in the reverse order. Be patient! 1 Link to comment Share on other sites More sharing options...
jherrera55buickcentury Posted May 22, 2020 Share Posted May 22, 2020 Thanks for the info. You’re absolutely right. It took a lot of my patience but I finally got it. do you know if there is a filler rubber or something for the rear of the glass on both rear doors? there is this big open area here. 1 Link to comment Share on other sites More sharing options...
95Cardinal Posted May 22, 2020 Author Share Posted May 22, 2020 Juan, Looks like the 55 is quite different from the 58. On a 58, the door weatherstrip comes up over the rear edge and attaches along the upper edge of the door. If you have a 1955 Fisher Body Service Manual or a Buick Body Parts book, there should be pictures of that area. Here is what the rear, upper corner of the 58 weatherstrip looks like: Link to comment Share on other sites More sharing options...
old-tank Posted May 22, 2020 Share Posted May 22, 2020 Hi Juan, sorry I missed the part where you have a 55 (maybe start a new thread with a specific title) Anyhow I have two model 63 four door hardtops for 55. There is a formed piece of rubber held by a stainless strip, screwed to the door. Send me a PM and I can supply the body manual. Both of my cars are late production and both made in Dallas, TX There were two different mechanisms on the first year four door hardtop. Link to comment Share on other sites More sharing options...
jherrera55buickcentury Posted May 22, 2020 Share Posted May 22, 2020 Please excuse my ignorance but I’m trying to figure out how to pm you. Link to comment Share on other sites More sharing options...
Rusty Heaps Posted May 22, 2020 Share Posted May 22, 2020 I just thought I’d throw these pics in from a junkyard I’m going to when weather permits. Unfortunately rain is in the forecast for the next few days. Don’t cry when you see the pics. I know, it’s an Olds, not Buick. But some interchange. 1 Link to comment Share on other sites More sharing options...
Rusty Heaps Posted May 22, 2020 Share Posted May 22, 2020 For some reason I’m only allowed one pic at a time Link to comment Share on other sites More sharing options...
neil morse Posted August 26, 2020 Share Posted August 26, 2020 (edited) Congratulations, Joe! I just read on the Hemmings website about your fabulous win of the AACA Zenith award this past weekend. So well deserved! Here's a link to the story for people who may have missed it: https://www.hemmings.com/stories/2020/08/26/a-buick-century-caballero-is-the-first-post-war-car-to-win-the-aacas-zenith-award?refer=news&utm_source=edaily&utm_medium=email&utm_campaign=2020-08-26 Neil Edited August 26, 2020 by neil morse (see edit history) 4 2 Link to comment Share on other sites More sharing options...
95Cardinal Posted August 26, 2020 Author Share Posted August 26, 2020 Thanks, Neil! And thanks for posting the Hemmings link, too. Joe 1 Link to comment Share on other sites More sharing options...
lancemb Posted August 27, 2020 Share Posted August 27, 2020 Awesome job Joe, well-deserved! 1 Link to comment Share on other sites More sharing options...
avgwarhawk Posted August 27, 2020 Share Posted August 27, 2020 Well deserved. Beautiful wagon! 1 Link to comment Share on other sites More sharing options...
EmTee Posted August 28, 2020 Share Posted August 28, 2020 Joe, the fact that you did the work yourself and shared it with us on this forum makes the result all the more impressive to me. Congratulations! 4 Link to comment Share on other sites More sharing options...
95Cardinal Posted August 29, 2020 Author Share Posted August 29, 2020 On 8/26/2020 at 9:23 PM, lancemb said: Awesome job Joe, well-deserved! On 8/27/2020 at 12:55 PM, avgwarhawk said: Well deserved. Beautiful wagon! 12 hours ago, EmTee said: Joe, the fact that you did the work yourself and shared it with us on this forum makes the result all the more impressive to me. Congratulations! Thank you, everyone! Link to comment Share on other sites More sharing options...
neil morse Posted December 23, 2020 Share Posted December 23, 2020 A heads up to everyone -- don't miss the great article on Joe's Caballero in the November/December issue of Antique Automobile with wonderful photos by West Peterson. The lead double-page side-view photo shows just how perfect the fit and finish of body panels and trim is on this car. Probably better than any Caballero at the time it left the factory! 5 1 Link to comment Share on other sites More sharing options...
95Cardinal Posted December 24, 2020 Author Share Posted December 24, 2020 Thanks, Neil! 1 Link to comment Share on other sites More sharing options...
Elpad Posted December 26, 2020 Share Posted December 26, 2020 Enjoyed the article. Well deserved recognition on the excellent wagon we got to see built through this thread. Congratulations 👏 Link to comment Share on other sites More sharing options...
sebastienbuick Posted December 26, 2020 Share Posted December 26, 2020 On 5/22/2020 at 7:50 PM, Rusty Heaps said: I just thought I’d throw these pics in from a junkyard I’m going to when weather permits. Unfortunately rain is in the forecast for the next few days. Don’t cry when you see the pics. I know, it’s an Olds, not Buick. But some interchange. great restoration project Link to comment Share on other sites More sharing options...
JohnD1956 Posted April 17, 2021 Share Posted April 17, 2021 @95Cardinal Congratulations on the write up in Hemmings Classic Cars June 2021 issue # 201. Almost can't wait for part 2 next month. 1 Link to comment Share on other sites More sharing options...
95Cardinal Posted April 17, 2021 Author Share Posted April 17, 2021 17 minutes ago, JohnD1956 said: @95Cardinal Congratulations on the write up in Hemmings Classic Cars June 2021 issue # 201. Almost can't wait for part 2 next month. Thanks John. I haven't seen the magazine yet, so I'm looking forward to seeing the article and photos! 2 Link to comment Share on other sites More sharing options...
JohnD1956 Posted April 18, 2021 Share Posted April 18, 2021 4 hours ago, 95Cardinal said: Thanks John. I haven't seen the magazine yet, so I'm looking forward to seeing the article and photos! You won't be disappointed. You really did such a great job and It looks fantastic! 1 Link to comment Share on other sites More sharing options...
EmTee Posted April 18, 2021 Share Posted April 18, 2021 11 hours ago, JohnD1956 said: You won't be disappointed. Hemmings' photographers do a great job. I subscribe to HMM and the photos are what hooked me! 1 Link to comment Share on other sites More sharing options...
95Cardinal Posted April 19, 2021 Author Share Posted April 19, 2021 11 hours ago, EmTee said: Hemmings' photographers do a great job. I subscribe to HMM and the photos are what hooked me! Barry Kluczyk, a professional freelance photographer, took all the new images for the HCC article. He did a great job! The detailed "work-in-process" images are my photos. 1 2 Link to comment Share on other sites More sharing options...
ADNMgt350h Posted December 17, 2022 Share Posted December 17, 2022 Hello Albuquerque NM I'm new to this forum and have enjoyed this restoration thread. This summer I picked up a 57 Caballero that's in near perfect original condition. I've spent the last few month going through it after being parked in a garage for 50 plus years. I'm just about done, and I’m looking forward to now detailing it up. One think I've been trying to locate is the piece of weather stripping that attaches to the front of the rear roll up window. Any idea where I might find this rubber? 6 Link to comment Share on other sites More sharing options...
95Cardinal Posted December 17, 2022 Author Share Posted December 17, 2022 Great looking car! I'm looking forward to seeing more of it. I don't think the 57 and 58 window seal systems are identical. Have you tried CARS (oldbuickparts.com)? @1957buickjim will know what you need; he just finished a 57 hardtop wagon. Joe 1 Link to comment Share on other sites More sharing options...
EmTee Posted December 17, 2022 Share Posted December 17, 2022 Nice wagon! What kind of tires are those? I'd like to see a better picture of those whitewalls... Link to comment Share on other sites More sharing options...
ADNMgt350h Posted December 18, 2022 Share Posted December 18, 2022 The tires a 50 year old Generals, they look cool and hold air but thats about all they are good for. Some new white walls are on there way... 5 Link to comment Share on other sites More sharing options...
EmTee Posted December 18, 2022 Share Posted December 18, 2022 (edited) Wow - those are unique! I don't recall ever seeing a set of those before. It would almost be worth another set of rims to mount your 'driving tires'. Those could be used for display only. Are they new enough to have letter sizing (e.g., H78-15) or do they have an all numerical size (e.g., X.XX-15)? Edited December 18, 2022 by EmTee (see edit history) Link to comment Share on other sites More sharing options...
1957buickjim Posted December 19, 2022 Share Posted December 19, 2022 Nice Car! Congratulations on your new addition. Feel free to PM me regarding anything you might need for the wagon. I probably can help in some form or fashion. As Joe said, I just finished a 57 Riviera Estate Wagon this past summer. What is the paint scheme on your wagon? Would love to see some interior pictures and engine compartment pics as well. 6 Link to comment Share on other sites More sharing options...
8E45E Posted November 12, 2023 Share Posted November 12, 2023 Congratulations on also making it on the cover of the December, 2023 issue of Collectible Automobile! Excellent photo essay of it with crystal clear sharp detail pictures of it inside. Craig 1 Link to comment Share on other sites More sharing options...
bkyrd_wrench Posted February 12 Share Posted February 12 A great restore effort. I've noticed that many photo links are "broken". Looks like the place where they were (flicker?) removed them? Very sad. Link to comment Share on other sites More sharing options...
95Cardinal Posted February 13 Author Share Posted February 13 On 2/12/2024 at 9:11 AM, bkyrd_wrench said: A great restore effort. I've noticed that many photo links are "broken". Looks like the place where they were (flicker?) removed them? Very sad. Yes, I closed out my Flickr account and am slowly re-linking the images. If you follow the thread, you'll be notified as I make updates. Joe 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now