packick Posted August 15, 2019 Share Posted August 15, 2019 Here's something I have always wondered about so I thought I'd pose this question to the Post War Buick gurus. Let's say I want to torque a bolt or nut, to 90 ft. lbs. and I have a 1/2” drive torque wrench. I put the socket on the torque wrench, dial in 90 ft. lbs. on the wrench, and tighten the bolt until it clicks. No problem. Now let's say I add a 6” or 12” extension to the wrench and attach the same socket onto the extension. Would there still be a 90 ft. lbs. torque on the bolt or do you lose some torque because of the extension? Or let's say I add an adapter to go from the 1/2” drive torque wrench to a 3/8” drive socket. Again, would I still have 90 ft. lbs. on the bolt? What about using an adapter and an extension? Still 90 ft. lbs.? And finally, what about using a flex socket? Still 90 ft. lbs.? This doesn't keep me up at nights but I have always wondered. 1 Link to comment Share on other sites More sharing options...
Kosage Chavis Posted August 15, 2019 Share Posted August 15, 2019 38 minutes ago, packick said: This doesn't keep me up at nights but I have always wondered. Funny...I have always wondered the same thing. I assumed that you did and I would always add a little more depending on how much torque was required when adding anything between the socket and torque wrench. Looking forward to a definite answer. Link to comment Share on other sites More sharing options...
Frank DuVal Posted August 15, 2019 Share Posted August 15, 2019 As long as the socket is still in line with the drive pin of the torque wrench, the reading does not change. i.e. the square drive of the wrench still points directly into the square hole of the socket and centered on the nut or bolt head, even if it is 2 feet away (or any amount), the reading is OK. Now, put an extension on the wrench that moves the socket laterally away from the square drive, and now you need to do math. Many pictures of this on the internet*. i.e. if you use a crows foot socket, the reading is WRONG. A crows foot puts the head of the bolt or nut not inline with the square drive of the wrench. Now, you do need to hold the wrench and extensions so the bolt/nut is still in line with the square drive of the wrench, otherwise you will introduce an error! No swivel sockets..... or wobble extensions....😲 * https://www.engineersedge.com/manufacturing_spec/torque_wrench_1.htm 4 Link to comment Share on other sites More sharing options...
Bloo Posted August 15, 2019 Share Posted August 15, 2019 A bunch of extensions can act as a spring and limit torque. Thats the principle on which a torque stick works. Put the socket right on the torque wrench if you can. If you cant, use a thick extension, and as little extra length as you can. Flex sockets and wobbly extensions will behave unpredictably. Never do that unless you have to (and then you cant quite believe the number). With a crowfoot wrench, the actual torque can be calculated based on the amount of offset in the crowfoot. 2 Link to comment Share on other sites More sharing options...
SpecialEducation Posted August 15, 2019 Share Posted August 15, 2019 Most torque specs have a range. Use the higher end of the range if you are worried about the flex of the extension. If a range isn’t given, it’s a pretty safe bet that +\- 10% is acceptable. Put the crow’s foot or torque adapter 90° to the wrench centerline and you don’t have to do math. 1 Link to comment Share on other sites More sharing options...
avgwarhawk Posted August 15, 2019 Share Posted August 15, 2019 As I understand it, the torque wrench will give way at the set lbs no matter the length of the extension. But as others stated, always use a straight strong extension. 1 Link to comment Share on other sites More sharing options...
Frank DuVal Posted August 16, 2019 Share Posted August 16, 2019 Torque Sticks are designed to twist and limit torque. Typical 3/8" straight extensions should be beefy enough for 150 or so foot pounds (1800 inch-pounds). 1/2" extensions should be 400 ft-lbs (5000 inch-lbs). If you see the extension twisting, then torque at the end of the extension will be lower than at the wrench. Link to comment Share on other sites More sharing options...
NTX5467 Posted August 17, 2019 Share Posted August 17, 2019 In general, the "extension: should be as short as possible and still get the job done. From what I've seen, IF the extension starts to flex from the turning force being applied, then you are probably in some "territory" you shouldn't be. OR you need an extension appropriate for such use. The first torque wrench I bought was a "beam" style torque wrench. They kind that was all you could get in the earlier '60s, before the "clicker" wrenches. Much easier to use the late-model clickers, by observation. Just set it and wait for the "click" feel and sound. BUT if you really want to "feel" things, then the beam wrench is the one. A correctly-calibrated clicker is probably the best thing to have, generally. In the '90s, the "big thing" was the Torque Sticks for wheel lug nuts. Color codes for the level of torque the lug nuts were supposed to be tightened to. Almost always used with a pneumatic impact wrench. NTX5467 1 Link to comment Share on other sites More sharing options...
Frank DuVal Posted August 18, 2019 Share Posted August 18, 2019 On 8/16/2019 at 9:26 PM, NTX5467 said: Almost always used with a pneumatic impact wrench. Make that DESIGNED for use with pneumatic impact wrench. They are not calibrated for use with clicker torque wrenches, or regular ratchets.etc. I agree that the beam type gives good feel. I use my beam types with a welded adapter to check calibration of my clickers. 😉 As long as you set the pointer to zero , what can become uncalibrated on a beam wrench? Metal goes bad???? 3 1 Link to comment Share on other sites More sharing options...
Joseph P. Indusi Posted August 27, 2019 Share Posted August 27, 2019 I always store my clicker type at the lowest torque setting when not in use. Joe 1 1 Link to comment Share on other sites More sharing options...
leon bee Posted August 27, 2019 Share Posted August 27, 2019 All I have is a Monkey Wards beam wrench I bought 40 some years ago. I've never questioned whether it was good enough for the junk I work on. 1 Link to comment Share on other sites More sharing options...
ply33 Posted August 27, 2019 Share Posted August 27, 2019 7 hours ago, leon bee said: All I have is a Monkey Wards beam wrench I bought 40 some years ago. I've never questioned whether it was good enough for the junk I work on. Probably good enough for anything: That type wrench has nothing to wear out. Just make sure the pointer is centered (bend it back if need be) before use. The main issue is that it takes a little practice to use it properly and you have to be in a position where you can read the scale while you are tightening the fastener. As pointed out above by Frank DuVal, you can trust them to be accurate enough to use them to check the calibration on the click type wrenches. 1 Link to comment Share on other sites More sharing options...
Ben Bruce aka First Born Posted August 27, 2019 Share Posted August 27, 2019 I have a craftsman bought in the early '50s . Been through a lot. Ben Link to comment Share on other sites More sharing options...
Joseph P. Indusi Posted August 29, 2019 Share Posted August 29, 2019 I have a GM torque wrench for AC spark plugs from the 50’s inherited from my uncle who was a parts and service manager in Olds, Buick and Cadillac dealers. A very nice tool made in the USA. Joe 1 Link to comment Share on other sites More sharing options...
old-tank Posted August 29, 2019 Share Posted August 29, 2019 12 hours ago, Joseph P. Indusi said: I have a GM torque wrench for AC spark plugs from the 50’s inherited from my uncle who was a parts and service manager in Olds, Buick and Cadillac dealers. A very nice tool made in the USA. Joe Pictures? Link to comment Share on other sites More sharing options...
Joseph P. Indusi Posted September 3, 2019 Share Posted September 3, 2019 some photos of the AC Spark Plug torque wrench made by Jo-Line Tools. Joe 2 1 Link to comment Share on other sites More sharing options...
FLYER15015 Posted September 6, 2019 Share Posted September 6, 2019 I'm with Ben, and still use my circa 60's Craftsman beam type torque wrench. If I want 90 #, I pull on it till the little pointer says 90. Being up in years, I will some times put a cheater pipe on the handle. It still reads 90 # weather I use my hands or a 6' pipe. And I sleep like a baby at night, Unless I start thinking about my water pump bearings..................... But that's for another thread. Mike in Colorado 1 Link to comment Share on other sites More sharing options...
Marty Roth Posted September 8, 2019 Share Posted September 8, 2019 On 9/6/2019 at 5:05 PM, FLYER15015 said: I'm with Ben, and still use my circa 60's Craftsman beam type torque wrench. If I want 90 #, I pull on it till the little pointer says 90. Being up in years, I will some times put a cheater pipe on the handle. It still reads 90 # weather I use my hands or a 6' pipe. And I sleep like a baby at night, Unless I start thinking about my water pump bearings..................... But that's for another thread. Mike in Colorado Thanks Mike, Now you've got me thinking about MY water pump bearings, ... and the slow leak from the rear end - - - the Buick's, not mine , time to make a differential rear plate gasket, and use some good sealer, ... again on the '37 - - - Link to comment Share on other sites More sharing options...
NTX5467 Posted February 16, 2020 Share Posted February 16, 2020 The extension on the SOCKET SIDE of the torque wrench needs to be a short as possible, but long enough that you can bet a right angle rotation of the wrench's handle. As in tightening a lug nut and needing fender/body clearance. DO hold the socket end of the wrench to ensure it is always at a right angle to the fastener. At "90", even a 3/8" extension should not deflect enough to make a difference in the torque reading. NOW . . . do NOT do all "90" at once! Just as with a cylinder head bolt, you start with "30", which is what you can do with your basic hand ratchet to snug things up AND in the correct position/location. When everything's seated at "30", then you can progress toward "90" in "15" or so increments. Better to have everything pulled-down in easy increments! More time consuming, but better on the fasteners and the item being fastened. No need to "flat rate" things on YOUR car! Enjoy! NTX5467 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now