Oregon Desert model 45 Posted September 6, 2016 Share Posted September 6, 2016 I was installing the oil pan on my 1924 6 cyl engine and discovered some tapped holes in the aluminum crank case casting have been stripped out. These are adjacent to the main bearing end seals. I can put a nut over the bolt tail at the forward location, but the flywheel blocks access to do this at the rear location. Locations are marked with red arrows in the photo below. Should I just omit the bolt at the stripped out rear locations and put a nut over the next adjacent bolt to prevent it from pulling out ? Should I try to install a helicoil threaded insert ? has anyone else installed an insert in an aluminum casting this old ? Kevin BCA # 47712 Link to comment Share on other sites More sharing options...
ply33 Posted September 7, 2016 Share Posted September 7, 2016 Don't know about doing it in a casting that old, but when I worked in a aerospace factory in the 1970s all threaded holes in aluminum castings had steel inserts installed in them. I suspect that a properly installed insert (helicoil or other brand/style) will be stronger than original. Link to comment Share on other sites More sharing options...
Larry Schramm Posted September 7, 2016 Share Posted September 7, 2016 Here is what GM now recommends for repairing stripped out threads in aluminum blocks like for head bolts. http://www.timesert.com/ Link to comment Share on other sites More sharing options...
Restorer32 Posted September 7, 2016 Share Posted September 7, 2016 We've used Helicoils to repair many aluminum parts. A bit expensive since you have to buy the tool for each size. Link to comment Share on other sites More sharing options...
DonMicheletti Posted September 7, 2016 Share Posted September 7, 2016 You can get away with just leaving the bolts out of some locations (I think the front is OK for sure). However some holes are tapped through to the inside of the crankcase. Those will leak like heck if you leave them out. To test you can poke a rod into the screw hole and see if it either bottoms out, goes through to the inner crankcase or comes out to the outside of the crankcase. With so many bolts there is no danger of anything falling apart. Leaving the 2 bolts out at opposite ends of the pan is no big deal. Obviously, Helicoiling the crank case is the right way to go, but you'd have to be carefull to get things straight and square. Link to comment Share on other sites More sharing options...
my31buick Posted September 7, 2016 Share Posted September 7, 2016 does aluminum and steel together cause some kind of corrosive reaction? if so, would it be an idea to use corrosion inhibitor on this project when putting in the helicoil? Link to comment Share on other sites More sharing options...
Bob Engle Posted September 7, 2016 Share Posted September 7, 2016 If this were my car, I would use the GM recommended repair. Larger diameter threads in the aluminum gives better strength. Drilling for helicoils is best done in a mill or drill press so there is no wobble when drilling. A loose hole will mean a loose helicoil. Corrosion will be less of an issue with the full insert. Bob Engle Link to comment Share on other sites More sharing options...
Larry Schramm Posted September 8, 2016 Share Posted September 8, 2016 With the amount of oil in the area, corrosion should not be a problem. I think the helicoils are made of stainless steel. Link to comment Share on other sites More sharing options...
Barney Eaton Posted September 8, 2016 Share Posted September 8, 2016 (edited) I often use inserts when rebuilding headlight motors for Buick Reattas. The only problem I have seen is cracking the part if the tap drill is too small.....there is very little aluminum around the holes I need to repair. If the tap drill is too small, then the pressure of tapping for the insert can crack or break thru the small amount of material. This should not be an issue on an hefty part like your engine block. On the dissimilar materials.......the original bolts were steel in aluminum.....right? Edited September 8, 2016 by Barney Eaton (see edit history) Link to comment Share on other sites More sharing options...
JV Puleo Posted September 8, 2016 Share Posted September 8, 2016 As a general rule, threading aluminum castings is a poor idea although it is frequently done. High end cars and industrial equipment nearly always used some sort of insert, especially if the bolt is expected to be removed and replaced frequently. For instance, Rolls Royce used bronze inserts in their aluminum heads and through bolts to hold oil pans on. Aluminum is actually very abrasive, especially aluminum oxide (effectively aluminum rust) so it is fairly common to see steel bolts broken off in aluminum castings. I have several in my 1910 Mitchell and repairing them will be a chore. All will get bronze or steel inserts. That said... I think the best solution in your case is a steel insert. The problem is that the larger hole cannot be drilled freehand. It is simply impossible to do that straight enough, without any wobble. As your engine is assembled, I would suggest making some sort of bolt-on fixture to center and guide the drill... a "super drill bushing" of sorts. If you made an identical fixture with a larger hole you could use it to guide the tap so that everything would be in perfect alignment. Does the hole go through or, can it? This would be far easier to work with although you will have to pack underneath it with something like an oil soaked rag to catch the chips from the drilling and tapping. You don't want them floating around in the engine. Go to the McMaster Carr on-line catalog and search for "threaded inserts"... there are several types available. I prefer the threaded steel inserts when there is metal enough around the hole but have used heli-coils where I had to deal with a tight fit. To hold on an oil pan – not a high stress application – either will work. I'd also use one of the never-seeze solid lubricants on all the bolts that are threaded into aluminum. If used properly, this eliminates many of the problems with steel bolts sticking in aluminum castings. Link to comment Share on other sites More sharing options...
Restorer32 Posted September 8, 2016 Share Posted September 8, 2016 Helicoils are stainless steel. Link to comment Share on other sites More sharing options...
26-25Buick Posted September 10, 2016 Share Posted September 10, 2016 An to answer the corrosion question. It is true aluminium is anodic to steel or in other words will corrode to protect the steel and corrode even faster to protect stainless steel. There are however a few things working in your favour here that means it's less of an issue. For corrosion to occur you need a conductive electrolyte e.g. Water, which if the part is wet with oil that's not going to happen. The second thing that helps here is what is called anode to cathode ratio. If you can't avoid dissimilar metals being connected the best way to have this ratio is with a large anode and a small cathode as you have lots of metal trying to protect just small pieces, which is the case here also. So I think whichever you choose its not going to be an issue unless you go really left field and find an insert that corrodes to protect the aluminium. Link to comment Share on other sites More sharing options...
Guest Staley Posted September 11, 2016 Share Posted September 11, 2016 Timesert. I use them at my auto shop and they are absolutely fantastic. Link to comment Share on other sites More sharing options...
JerryVan Posted September 13, 2016 Share Posted September 13, 2016 I would definitely use Heli-Coils here. Should be no problems at all. Link to comment Share on other sites More sharing options...
Brian_Heil Posted September 14, 2016 Share Posted September 14, 2016 Heli-coil and done. It's an oil pan, not a spaceship, you will be fine. Do your best not to drill through to the sump area if possible, but if you do, put sealant on the coil and the bolt. Don't omit this location. The reason these holes stripped is these are the most important fasteners on the pan since they are next to the cap and the 'long' distance over the cap that needs to maintain clamp load to maintain a seal to stop leaks and someone has been reefing on them before to stop a leak and stripped the threads for you. Make sure your bolt is long enough but not so long it bottoms out in the hole and has 2 time the diameter of bolt for thread engagement depth/distance and mind your torque. Your engine has an 'oil loss system' for the lube you put in the rocker shafts so your engine will be covered in oil soon enough. Link to comment Share on other sites More sharing options...
Oregon Desert model 45 Posted September 20, 2016 Author Share Posted September 20, 2016 Thanks for the advice. I disassembled the pan, oil system, and flywheel to gain access to install helicoils. Fortunately, the stripped out holes don't penetrate into the crank case. I can make a drill guide by drilling the helicoil tap drill diameter thru a small block of steel using the drill press to ensure perpendicularity. This block can then be centered and clamped over each stripped hole, and allow use of a portable drill motor to drill a perfectly straight hole thru the aluminum housing flange. I also ordered a helicoil kit which should arrive sometime in the next week. Kevin 1 Link to comment Share on other sites More sharing options...
Brian_Heil Posted September 20, 2016 Share Posted September 20, 2016 And I need to make a correction. This is a 1924 so you have (first year 6 cylinder) pressurized oil to the rocker arms and return drains and not an oil loss system for these. All the more reason to fix this and keep the engine exterior dry. Link to comment Share on other sites More sharing options...
superbuick Posted September 26, 2016 Share Posted September 26, 2016 I have used Heli-coil and Timeserts in my shop repairing engine parts for over 35 years. The Timesert is the best way to repair hands down. It is the same size as the Heli-coil but is a one piece insert unlike the 'coil'. Timesert is swedged in place during installation and has never moved or come loose during future servicing. The heli coil will work OK for this application. I consider the timesert as a permanent repair. 1 Link to comment Share on other sites More sharing options...
Oregon Desert model 45 Posted October 4, 2016 Author Share Posted October 4, 2016 Project update: 12 helicoils installed and all stripped or imperfect tapped holes in the aluminum casting are fixed! Using a freshly sharpened tap drill and tap from the helicoil kit, both drill & tap operations went very smoothly. I used the pictured drill guide and another similar guide made from a block of wood to start the tap straight into the holes. thanks for all the advice. Kevin 2 Link to comment Share on other sites More sharing options...
MrEarl Posted October 22, 2016 Share Posted October 22, 2016 Kevin, is this the last picture you took of this project of do you perhaps have a picture of one of the actual helicoils being inserted or installed. or of the oil pan back on? Link to comment Share on other sites More sharing options...
Oregon Desert model 45 Posted October 25, 2016 Author Share Posted October 25, 2016 I took one more photo of tapping for the helicoil using a wood block for a guide, then the next photos are of the motor getting installed into the chassis- sort of a fast forward. Installing the helicoil itself was pretty quick. Kevin 4 Link to comment Share on other sites More sharing options...
dibarlaw Posted October 27, 2016 Share Posted October 27, 2016 Kevin : Thanks for the progress photos. I will also be getting a rough engine with the 1925-45. The blocking of the engine will be helpful for me for when storing it. 1 Link to comment Share on other sites More sharing options...
sligermachine Posted January 11, 2018 Share Posted January 11, 2018 On 9/7/2016 at 5:23 AM, Restorer32 said: A bit expensive since you have to buy the tool for each size. Not if u figure how much to replace a old part to your favorite car you're restoring .the big cutting tool company that I buy all my end mills from lends them for free if u buy the insert from them cost like $ 2.20 for a 1/2-13 tpi helicoil insert just find out who all the big machine shops use in town .I bet they do the same better than buying helicoil taps of each size .I would buy the tap only thats all you need make the rest with a bench grinder in under 1 minute -Kyle Link to comment Share on other sites More sharing options...
sligermachine Posted January 11, 2018 Share Posted January 11, 2018 looks great nice work Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now