Labrat Posted April 11, 2018 Share Posted April 11, 2018 I replaced the MAF and that didn't work. I then replaced the water temp. sensor under the MAF and no help there either. The cars feel like it's running rich after starting warm but will run OK after driving a few minutes or revving it up for a minute before driving. The coil packs look like new. The car just turned 80K. All help would be appreciated. Link to comment Share on other sites More sharing options...
Ronnie Posted April 11, 2018 Share Posted April 11, 2018 You could have an injector leaking fuel into the intake while the engine is turned off. When you start the engine it would run rough until the fuel puddled in the intake is burned off. A fuel pressure leak down test might help you determine if that is the problem. Link to comment Share on other sites More sharing options...
D-a-n-i-e-l Posted April 11, 2018 Share Posted April 11, 2018 Egr could be sticking. Link to comment Share on other sites More sharing options...
jroman Posted April 11, 2018 Share Posted April 11, 2018 Check the fuel pressure regulator diaphragm. It may be leaking. Pull the vacuum hose off it and check for fuel . It should be dry on vacuum hose side. Link to comment Share on other sites More sharing options...
Labrat Posted February 13, 2019 Author Share Posted February 13, 2019 Still having the problem with idle after the engines is warm. It starts and runs great and is fine until it turn it off and re-start after it has sat for 10 minutes or more. I have to rev up the motor to clear the flooded rough feeling before it is drive- able. Usually about a minute of fast idle clears it up. It stalled at a red light twice yesterday. RPMs dropped below 500 and quit. Restarted with no problem and ran fine except for fluctuating idle at the next light. My mechanic over the last few months has replaced the injectors, spark plugs, o2 sensor, water temp sensor, MAF, TPS (had bad code ) (the only code I've had so far ever) and the IAC. I don't know if he cleaned under the IAC but will check . Fuel pressure reg was fine. I don't know if the EGR valve was checked, again I'll ask tomorrow. The car has 83K miles so it was probably time to change most of the stuff so we did. I don't mind the cost, I love the car and plan on driving until I'm gone but I've got to get it safe to drive. Any help would be appreciated. Link to comment Share on other sites More sharing options...
Barney Eaton Posted February 14, 2019 Share Posted February 14, 2019 My guess..........cam sensor (magnet) other clues are poor gas mileage and poor performance. Link to comment Share on other sites More sharing options...
Dashmaster Posted February 14, 2019 Share Posted February 14, 2019 Another Thought Do you know what the coolant temperature is while driving it before the problem ? My thought is that its running in open loop mode due to coolant leak past thermostat or no Thermostat. When you stop the car it gets warm enough to do into closed loop where the sensors come into play during the warm restart, Once its has been running again the coolant temperature falls below the sensor threshold and back into open loop. You still have a problem. I would check the Cam Sensor Magnet and I have had more then one bad new OX sensor out of the box, You can unplug the OX sensor and it will stay in open loop. If running in open loop the problem does away you will need to check all the sensors. The 3 sensors that all affect fuel and air are IAC, MAF and OX. Link to comment Share on other sites More sharing options...
Labrat Posted February 14, 2019 Author Share Posted February 14, 2019 (edited) I haven't noticed any change in performance, still very peppy and same with gas mileage. The temp gauge goes to its usual centered position in the right amount of driving. I thinking in ten minutes of stopping the temp can't fall far enough to matter as the car can have the problem that quick. I will have the Cam Sensor Magnet checked. and try unplugging the O2 sensor to test it. Barney how likely is it the cam magnet? Should I replace the cams sensor at the same time or maybe replace it first to see if that is the problem Any way to check the sensor before the big tear down? Also, how is this related to the warm verses cold temp. of the engine? Thanks. Edited February 14, 2019 by Labrat (see edit history) Link to comment Share on other sites More sharing options...
2seater Posted February 14, 2019 Share Posted February 14, 2019 This is a TPI engine without EGR and has an integrated PCV system, correct? My first thought was a vacuum leak but less places for that to occur on the L27 engine except the possible exception of where the upper and lower intake manifold bolt together. It seems most of the likely issues have been suggested already, but it would be helpful to have actual sensor readings at warm idle, all of them can be checked, except cam sensor, in diagnostics. Link to comment Share on other sites More sharing options...
Labrat Posted February 14, 2019 Author Share Posted February 14, 2019 I drove it this afternoon and now it is dead. Will start and run 1 seconds and dies. I let it cool an hour waiting for the tow truck and no change. Now maybe my mechanic can find the problem. He did clean the chamber under the IAC well and replaced the fuel pressure reg during the last attempt to fix it. He's going to pull the cam sensor and look at the magnet with his camera. I'm still open to ideas about the problem only occurring when it is up to temp. Thank goodness for this Forum. Link to comment Share on other sites More sharing options...
2seater Posted February 14, 2019 Share Posted February 14, 2019 Needs a fuel pressure gauge on it and a spark test indicator to simultaneously check for fuel and spark when it starts and then stops. Some fuel pressure should remain even if spark goes away. Link to comment Share on other sites More sharing options...
DAVES89 Posted February 14, 2019 Share Posted February 14, 2019 Maybe 2seater is on to something altogether different. It could be the fuel pump. I have been told that it is easier to diagnose a "dead" car then one with an intermittent issue. Link to comment Share on other sites More sharing options...
2seater Posted February 15, 2019 Share Posted February 15, 2019 It is possible the injectors lose signal too. The engine starts on the ICM under the coils and then control is taken over by the ECM. Link to comment Share on other sites More sharing options...
Ronnie Posted February 15, 2019 Share Posted February 15, 2019 3 hours ago, Labrat said: I drove it this afternoon and now it is dead. Will start and run 1 seconds and dies. I let it cool an hour waiting for the tow truck and no change. Now maybe my mechanic can find the problem. He did clean the chamber under the IAC well and replaced the fuel pressure reg during the last attempt to fix it. He's going to pull the cam sensor and look at the magnet with his camera. I'm still open to ideas about the problem only occurring when it is up to temp. Thank goodness for this Forum. The cam sensor or magnet will not cause the stalling problem you are describing. You can unplug the cam sensor and the engine will still run. 2seater gave you good advice on how to troubleshoot the problem. Link to comment Share on other sites More sharing options...
SCOTT's 90's Posted February 16, 2019 Share Posted February 16, 2019 On 2/14/2019 at 4:17 PM, 2seater said: Needs a fuel pressure gauge on it and a spark test indicator to simultaneously check for fuel and spark when it starts and then stops. Some fuel pressure should remain even if spark goes away. Very good suggestion from 2seater... When I was having similar stalling trouble I got both of those and put them in the back of seat (Not in the stow away) so that I could grab them real quick and do the tests on the side of the road - If need be. I actually did have to do this one day when it stalled - This proved that I did not have an immediate issue with fuel pressure or spark. Link to comment Share on other sites More sharing options...
DAVES89 Posted February 17, 2019 Share Posted February 17, 2019 You can leave the spark tester on all the time. I actually thought about buying three of them so I could watch the spark of the front three plugs every time I popped the hood. That way you only have to put the fuel pressure tester on. 1 Link to comment Share on other sites More sharing options...
Larry Schramm Posted February 17, 2019 Share Posted February 17, 2019 (edited) Does anyone have a scanner that you know like a Tech 2? That can usually pinpoint the problem fairly quickly. Another way to possible get into diagnostics on this car is to do the following. Turn the ignition on and start the car if it will start and press and hold the OFF and WARM buttons on the a/c at the same time and hold the for a few seconds. If I remember correctly that will put the car into diagnostic mode ( it will on '88's) and you should be able to see live data from the data stream. This will include coolant temp that the engine computer sees which might not be the same as the gauges. You should be able to scroll through all of the inputs to the computers. Engine temp when warm should be in the 190 F deg range. Remember that the car will not set a temp code as long as the coolant sensor sends a temp reading between -40 F and I think about 260 F the engine control module. That can be considered "normal" operating temp. As for the fuel pump, two things to do at the same time. First hook up a pressure gauge to the fuel rail. Then get in the car and just turn the ignition on and listen carefully. It might help to have someone listen under the back of the car. When you turn the ignition on but not start the car you should hear the fuel pump come on and stay on for about 6-10 seconds. If no sound, bad pump. Then look at the fuel gauge. If the pump runs, it should have more than 50PSI. If it has less, then the pump is going bad. A good pump will have about 60 PSI. The car can run sometimes at pressures as low as 40PSI, but not well or intermittently. Below 40, the car will not run. I could go on, but these are the basics. If you need more information, let me know. Edited February 17, 2019 by Larry Schramm (see edit history) Link to comment Share on other sites More sharing options...
2seater Posted February 17, 2019 Share Posted February 17, 2019 I am not certain about the normal fuel pressure for the TPI L27 engine, but the intake and fuel rail pressure I have for a TPI manifold appears to be the same as the '88-'90 LN3, or approximately 3bar or 43.5psi with key on and engine off. I believe later models did use a higher pressure. Link to comment Share on other sites More sharing options...
D-a-n-i-e-l Posted February 21, 2019 Share Posted February 21, 2019 On 2/16/2019 at 6:36 PM, Larry Schramm said: Does anyone have a scanner that you know like a Tech 2? That can usually pinpoint the problem fairly quickly. Another way to possible get into diagnostics on this car is to do the following. Turn the ignition on and start the car if it will start and press and hold the OFF and WARM buttons on the a/c at the same time and hold the for a few seconds. If I remember correctly that will put the car into diagnostic mode ( it will on '88's) and you should be able to see live data from the data stream. This will include coolant temp that the engine computer sees which might not be the same as the gauges. You should be able to scroll through all of the inputs to the computers. Engine temp when warm should be in the 190 F deg range. Remember that the car will not set a temp code as long as the coolant sensor sends a temp reading between -40 F and I think about 260 F the engine control module. That can be considered "normal" operating temp. As for the fuel pump, two things to do at the same time. First hook up a pressure gauge to the fuel rail. Then get in the car and just turn the ignition on and listen carefully. It might help to have someone listen under the back of the car. When you turn the ignition on but not start the car you should hear the fuel pump come on and stay on for about 6-10 seconds. If no sound, bad pump. Then look at the fuel gauge. If the pump runs, it should have more than 50PSI. If it has less, then the pump is going bad. A good pump will have about 60 PSI. The car can run sometimes at pressures as low as 40PSI, but not well or intermittently. Below 40, the car will not run. I could go on, but these are the basics. If you need more information, let me know. Just throwing out a tech two or any other scanner will not show more than the on board diagnostics. One of the awesome things our Reatti do. Link to comment Share on other sites More sharing options...
Larry Schramm Posted February 21, 2019 Share Posted February 21, 2019 2 minutes ago, D-a-n-i-e-l said: Just throwing out a tech two or any other scanner will not show more than the on board diagnostics. One of the awesome things our Reatti do. I agree, but with a Tech II, you will be able to see more than two items at a time. (at least I think that is what I remember) I have a Tech II and use it all of the time on our cars and friends & family, etc. There are typically more tests that can be run with a Tech II that can not be done with the onboard diagnostics. Link to comment Share on other sites More sharing options...
Labrat Posted February 25, 2019 Author Share Posted February 25, 2019 (edited) Mechanic checked the fuel pressure today and it was about 38 psi and bleeds down to 30 in 5 minutes. What should pressure be. I saw in and old post where Padgett said anything over 25 was OK. He replaced the fuel pressure reg. and no change ( i had a spare). Looks like fuel pump is bad for sure. Engine started but only ran a minute. He pulled the plugs and the were black and wet on all 6. Any way to change the pump without dropping the tank? Thanks to all for the help so far. Edited February 25, 2019 by Labrat (see edit history) Link to comment Share on other sites More sharing options...
2seater Posted February 25, 2019 Share Posted February 25, 2019 15 minutes ago, Labrat said: Mechanic checked the fuel pressure today and it was about 38 psi and bleeds down to 30 in 5 minutes. What should pressure be. I saw in and old post where Padgett said anything over 25 was OK. He replaced the fuel pressure reg. and no change ( i had a spare). Looks like fuel pump is bad for sure. Engine started but only ran a minute. He pulled the plugs and the were black and wet on all 6. Any way to change the pump without dropping the tank? Thanks to all for the help so far. 38psi under what conditions? Engine running, engine not running, the details are everything. Bleeding down to 30 that fast is a little excessive, but not horrible. Wet plugs would seem to indicate too much fuel, poor spark or multiple tries to start it with limited results, causing it to go through multiple prime cycles. Hot wire the pump by applying 12volts to the green connector near the brake cylinder to run the pump constantly and see what the results are. Try to start with it hotwired, it won't hurt anything. Link to comment Share on other sites More sharing options...
DAVES89 Posted February 25, 2019 Share Posted February 25, 2019 1 hour ago, 2seater said: 38psi under what conditions? Engine running, engine not running, the details are everything. Bleeding down to 30 that fast is a little excessive, but not horrible. Wet plugs would seem to indicate too much fuel, poor spark or multiple tries to start it with limited results, causing it to go through multiple prime cycles. Hot wire the pump by applying 12volts to the green connector near the brake cylinder to run the pump constantly and see what the results are. Try to start with it hotwired, it won't hurt anything. 2seater is right, if you have wet plugs I would think the engine is getting all the fuel it needs. The fuel pump bleeding down to 30 isn't bad either. I asked the question before and you said you would have your mechanic look into it. To clean the opening the Idle Air Control fits into. Last fall I bought a '89 Reatta that didn't start or idle good. He had bought but not installed an Idle Air Control and was sure that was going to fix it. I simply removed the old one sprayed the old IAC with carb cleaner and scrubbed with a tooth brush then did the same with the opening. A lot of gunk flowed out but after the IAC was back in the car fired right up and ran great. These cars have great engines, nothing different then the millions G M used on other cars. Just clean some stuff and then drive them. Who knows maybe your gas is bad because you might not be driving your car enough to keep the gas fresh. No reflection on you but I drive my Red and Black thousands of miles a year and have none of the drivability issues I see here on the forum. Even my 'vert gets driven about 100-200 miles a week every week it's out of storage. Link to comment Share on other sites More sharing options...
Labrat Posted February 26, 2019 Author Share Posted February 26, 2019 (edited) My mechanic checked the fuel pressure by powering the green connector and the pressure was 42 PSI steady. After an hour it was 25 PSI. He is going to re-clean the IAC bowl today. He checked the coil packs and they had a good blue spark and look to be in great condition. Running out of things to check. Aaargh! I drive the car several times a week so the gas is fresh. I live in Central Florida so there is no winter storage for me. Edited February 26, 2019 by Labrat (see edit history) Link to comment Share on other sites More sharing options...
2seater Posted February 26, 2019 Share Posted February 26, 2019 (edited) Fuel pressure sounds good, so likely is not the problem. That leaves two items, spark and fuel injector signal. A noid light or something to indicate off the injector connection would be helpful and spark tester(s) to see if the spark goes out. The two are sort of intertwined so determining which quits first may be difficult. Holding the throttle open slightly will bypass the IAC if that is restricted. I am almost to the point of suggesting the ECM as the culprit but unfamiliar with the '91 electronics. Edited February 26, 2019 by 2seater (see edit history) Link to comment Share on other sites More sharing options...
Ronnie Posted February 26, 2019 Share Posted February 26, 2019 10 minutes ago, 2seater said: That leaves two items, spark and fuel injector signal. A noid light or something to indicate off the injector connection would be helpful and spark tester(s) to see if the spark goes out. The two are sort of intertwined so determining which quits first may be difficult. One way to figure out if it's losing spark or the signal to the injector is hold the throttle open so the engine runs at about 1500 RPM. When the engine starts to die spray a little gas, or equivalent, into the throttle body. If the engine picks back up and runs the problem is fuel delivery. If it dies the problem is likely to be an ignition problem. EDIT: If the crank trigger is the problem you would lose spark and signal to the injectors. 1 Link to comment Share on other sites More sharing options...
Dashmaster Posted February 27, 2019 Share Posted February 27, 2019 Note sure if this helps. 2 years ago I had random misfire at speed above 45. Idle was Ok. But I had gone over everything 3 times or more. All my parts were new. I was so frustrated by this I almost put the car up for sale. Here is what affected my car. The main wire harness on the firewall running left to right was hanging down about even with spark plugs. I had the OX sensor wire separated from this harness but did not help. I pulled the harness back up to where it should have been and wire tied it. My random misfires stopped. Car ran great. I know my car is running good because it averages 25 mpg in mixed driving. My car does have have a slight rough idle when warm sitting at a light. rpms vary about 50. I have not looked into this because it does not cause any issues. Might be worth a look at that harness location. It might be picking up inducted signals from plugs, wires and OX sensor. Link to comment Share on other sites More sharing options...
Labrat Posted March 22, 2019 Author Share Posted March 22, 2019 It's still dead and there isn't anything left to replace but the ICM and the ECM. Fine with me! I have no clue which one is the likely culprit for the flooding issue on start-up now. Way past the rough idle problem now. Any help would be appreciated with advice on where to buy and what to buy Car is a '91. Thanks. Link to comment Share on other sites More sharing options...
Labrat Posted September 17, 2019 Author Share Posted September 17, 2019 Still haven't figures it out yet. Replaced even more stuff. Pulled the harness and didn't like the look of it at one end. This is the harness to the cam sensor, crank sensor, coil pack and part of the injector harness. The car ia a 1991. If any one has a harness I'm looking to beg borrow or buy one. Thanks, Labrat Link to comment Share on other sites More sharing options...
padgett Posted September 18, 2019 Share Posted September 18, 2019 About this point I would get out the MOATES.NET ALDL adaptionter and TunerProRT on a laptop and pull up everty value related to ignition. If could just have one, I'd start with the spark advance and check the knock count (OldPA3). Might even find my ignition scope. Link to comment Share on other sites More sharing options...
MRJBUICK Posted September 18, 2019 Share Posted September 18, 2019 rock auto lists the 14 terminal flat plug with pigtails called the ignition control module plug we had an 04 Lesabre that had a problem with that harness kept stalling intermittently until it was towed to the dealer to be replaced have you checked the dealer could it be possibly still available any 91 3800 is probably the same, lesabre, park, regal good luck Link to comment Share on other sites More sharing options...
Davidmorelli Posted January 25, 2022 Share Posted January 25, 2022 Hello, i am new here. But finaly Aster 3 years of searching finaly someone have the same problem like my girlfriends Buick Skylark 1989 3.3. Exactly the same. Cold have no problems, run to operating temp. Turn off and restart and start run like crap and very rich only one possibility is to high rev engine shortly and after that run like no problem until next hot start. Didnt help the ICM? Its the Last thing that i didnt chaged too. Do you have some update? Thank you very much. I didnt have heart to rev engine like that every time. Thanks David. Link to comment Share on other sites More sharing options...
2seater Posted January 25, 2022 Share Posted January 25, 2022 Many of the same symptoms that Dave's89 started out with which got progressively worse, thread is recent about his car misbehaving. In his case the crank sensor was loose in the holder. Just spitballin' but likely everything held tight when cold and looser when warmed up. I just reread the above thread and neither the ICM below the coils was replaced nor the crank sensor. I may have missed that but both items are temperature sensitive. The 3300 does not have a cam sensor if memory serves, it is a batch fire fuel system. The same items as above should be looked at, actual fuel pressure, fuel pressure regulator hose for fuel leaking, and spark while cranking. Disconnect the MAF and see if that helps the warm richness issue. It should start and run with the MAF disconnected. Link to comment Share on other sites More sharing options...
2seater Posted January 25, 2022 Share Posted January 25, 2022 Oops, the Daves car behaving badly is on ROJ. My bad Link to comment Share on other sites More sharing options...
Davidmorelli Posted January 25, 2022 Share Posted January 25, 2022 Ok thanks. I will make this tests but I tested injectors already and they are leak tight. So I will see. Yeah 3.3 didnt have cam sensor. Crank sensor i have new. New temp sensor and switch, new iac and tps Link to comment Share on other sites More sharing options...
2seater Posted January 25, 2022 Share Posted January 25, 2022 4 hours ago, Davidmorelli said: Ok thanks. I will make this tests but I tested injectors already and they are leak tight. So I will see. Yeah 3.3 didnt have cam sensor. Crank sensor i have new. New temp sensor and switch, new iac and tps Just to be clear, are the items mentioned, crank sensor, coolant temperature, iac and tps all new and installed? Link to comment Share on other sites More sharing options...
Davidmorelli Posted January 26, 2022 Share Posted January 26, 2022 Yeah all parts are change on car. Cleaned all connectors and checked wires. 😔 I am on the way to buy icm. Link to comment Share on other sites More sharing options...
B Jake Moran Posted January 30, 2022 Share Posted January 30, 2022 Wonder if Labrat ever got his issue solved? Link to comment Share on other sites More sharing options...
Labrat Posted January 30, 2022 Author Share Posted January 30, 2022 After going down the list of possible problem sources we changed everything in the most likely to be the problem order. Started with MAF and went from there. After new crank sensor, cam sensor IAC, ECU, O2 sensors, new Delphi coil packs, new injectors, multiples spark plugs that were ruined in the testing, wiring harness referenced in a earlier post, TPS, and probably somethings I'm forgetting. Bottom line after all that with still a problem we replaced the MAF again (the first thing changed) and the problem was fixed. AARGH!! New GM part was bad out of the box. Since I have no intention of EVER selling this car I don't care about the cost or effort. Just glad to have my favorite car of everything I've ever owned great again. Corvettes(4) Jaguars (3), Porsche, Lamborghinis(2) and other American sports cars this has always been my favorite. I appreciate the opportunity to own and drive those other fun cars but for me it's the Reatta that makes me smile every time I walk past it or drive it. Least valuable car I own in dollars but the most valuable in my heart. 3 Link to comment Share on other sites More sharing options...
Barney Eaton Posted January 30, 2022 Share Posted January 30, 2022 Seems we forget that almost every cars needs maintenance and things fixed from time to time. Some owners seem to think their Reatta is a money pit and decide to go with something different, Of course we will never hear from them about the issues they might have with their new choice. One of the scary things about newer cars are all the electronics. What happens when a vehicle is 10 years old, lets say you have a 2012 something. Individual parts are getting unavailable, the dealer and many parts houses only carry a complete assembly. Even if the pully on your power steering pump fails, you end up buying a complete power steering pump. Same thing with electronics. What if your "display" fails, you might as well have a 1988-89 Reatta with a CRT because you will be buying a new display assembly. From an economic standpoint, we would all be better off starting with a 2-4 year old used car and drive it for 2-3 years then do the same thing again. If we look back over the last 10-15 years.... what vehicles do you thing will become collectable in another 15 (when they are the age of our Reattas) very few except for some expensive exotics. On top of that I just paid the insurance on my '11 pick-up and '17 Enclave and the insurance is almost $100 per car per month..... but I can insure my Reatta (with mileage restrictions) for about $200 per year. Maybe the answer is to own 3-4 Reattas insure them a antiques and rotate driving them to keep the mileage within the insurance limits. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now