alsancle Posted September 13, 2016 Share Posted September 13, 2016 So I have an issue and I'm confused how it happened. I've got 4 stuck valves on an overhead valve straight 8. Here are the details: 1. Engine was done 25-30 years ago before I bought the car. 2. I would start car every 3/4 months and let it run to warm. I've done this for the last 14 years. 3. Car is stored in a basement garage, temp stays between 60-70 year round. This is not feel like a humid or moist environment but now I'm wondering so will get a humidity gauge. 4. I missed a start cycle and went 6 months and the car wouldn't start. A compression test showed no compression and we found the stuck valves. 5. With the valve cover off, there is plenty of oil in the head but the valves are really stuck hard. 6. I run 30 weight Valvoline racing oil. Only racing or aviation gas in the tank. It has never had pump gas since I've owned it. I'm totally confused as to how this happened. I understand in a car that sits for a long time, but is 6 months really that long? Link to comment Share on other sites More sharing options...
28 Chrysler Posted September 13, 2016 Share Posted September 13, 2016 A friend of mine has a 1958 Chevy 6 cyl. 1/2 ton PU. He started it after sitting for 4 months, heard a noise and the truck ran poorly. It turned out he had 2 broken rocker arms on 2 intake valves. the cause was a scummy build up on the valve stem. He has added Marvel Mystery Oil to the fuel tank and has not had a problem since. Link to comment Share on other sites More sharing options...
trimacar Posted September 13, 2016 Share Posted September 13, 2016 Old gas probably caused it, and unfortunately these days, old gas can be 6 months. And, from your description, you weren't adding new gas, just starting it every now and then. I learned the same lesson with a Lincoln that hadn't been run for a while. The gas had evaporated, and even with fresh gas in the tank, a problem occurred. I started the car, it ran fine, even drove it around some, got it up to operating temperature. The next day, it wouldn't start at all. After a lot of headscratching and cussing, we found out the valves were stuck and pushrods bent like pretzels. And when I say stuck, I mean STUCK! Had to drive them out with a punch and hammer. The old gas gummed up the stems, big time. One day I had a friend call me, he had two Pontiacs that had been sitting for not quite two years. He'd started them a couple of times. He went to start them again, and they wouldn't start. I told him to drop the gas tanks and clean them out, he looked at me like I was crazy. A couple of weeks went by, he called, "How'd you know it was bad gas, it wasn't that old?" He'd cleaned the tanks and fuel system and all was well. Ethanol gas can go bad in 6 months. Regular, non-ethanol modern gas MIGHT last two years, but probably not.... Link to comment Share on other sites More sharing options...
alsancle Posted September 13, 2016 Author Share Posted September 13, 2016 I hear you on the gas but this is AV gas, which I thought never went bad. Maybe eventually it does. This gas was probably a few years old. Link to comment Share on other sites More sharing options...
alsancle Posted September 13, 2016 Author Share Posted September 13, 2016 A couple days of penetrating oil and they freed up. Will drain the AV gas and I guess make sure I run through the tank more often. I'm still really surprised. Link to comment Share on other sites More sharing options...
rsb Posted September 14, 2016 Share Posted September 14, 2016 I don't know if it's an old wives tale but I put Premium (91 octane) fuel in my older cars that I don't drive as often. The thought is the higher octane fuel is less volatile and lasts longer. Link to comment Share on other sites More sharing options...
DonMicheletti Posted September 14, 2016 Share Posted September 14, 2016 When an engine sits, moisture, just due to humidity, accumulates in the crankcase and rocker cover. That moisture can condense in the valve stems and guides and cause to rust and often cause sticking. Especially true on a rebuilt engine where valve stem clearance is still close. That is how the oil in an engine not running for a long time can gunk up. Even though you do run the engine once in a while - the moisture still can build up. Link to comment Share on other sites More sharing options...
tom_in_nh Posted September 14, 2016 Share Posted September 14, 2016 I often wonder if the old time fix of reviving worn out valve guides via the "knurling" method helps to reduce stuck valves. Kind of makes sense as the oil is more apt to be trapped into the knurled grooves. I am contemplating doing that to my spare Packard inline six engine. Would that warrant a new topic for discussion? Comments? Link to comment Share on other sites More sharing options...
alsancle Posted September 15, 2016 Author Share Posted September 15, 2016 I would be interested in opinions on the knurling also. After freeing the valves over 3 days we were able to get it running again. I'm thankful there were no bent valves. Link to comment Share on other sites More sharing options...
Spinneyhill Posted September 15, 2016 Share Posted September 15, 2016 It is my understanding higher octane fuel has more aromatic components which evaporate faster than components in lower octane fuels, thus reducing the octane rating of the fuel. Starting an engine and idling it for a short while is a sure way to fill it with condensation. Even if run 'til the temp gauge comes to normal, the engine doesn't really reach operating temperature everywhere and evaporate all the water vapour inside it. The muffler will fill with water too. Mine has sticky valves because of a carbon build-up at the top of the stems. Do any of those "carbon burning" products actually work? 2 Link to comment Share on other sites More sharing options...
Larry Schramm Posted September 17, 2016 Share Posted September 17, 2016 On 9/15/2016 at 0:01 AM, Spinneyhill said: It is my understanding higher octane fuel has more aromatic components which evaporate faster than components in lower octane fuels, thus reducing the octane rating of the fuel. Starting an engine and idling it for a short while is a sure way to fill it with condensation. Even if run 'til the temp gauge comes to normal, the engine doesn't really reach operating temperature everywhere and evaporate all the water vapour inside it. The muffler will fill with water too. Mine has sticky valves because of a carbon build-up at the top of the stems. Do any of those "carbon burning" products actually work? I agree that just starting the vehicle for a little bit and then turning it off causes condensation issues. I know persons that start their cars every month all winter and let them run for a few minutes. I think that is a bad practice. When I put any vehicle away for the season, I always change the oil, take it out for a good drive, fill it up with gas and then park it. I do not start it until spring when I am going to get it out for the season. I have never had any issues with sticking valves, etc. Link to comment Share on other sites More sharing options...
Spinneyhill Posted September 17, 2016 Share Posted September 17, 2016 (edited) On 15/09/2016 at 11:16 AM, tom_in_nh said: I often wonder if the old time fix of reviving worn out valve guides via the "knurling" method helps to reduce stuck valves. Kind of makes sense as the oil is more apt to be trapped into the knurled grooves. I would imagine the rough knurled surface would be very good at grinding away inside the end of the valve guide. It would be a fiddle getting the knurling just deep enough that the material pushed up still fits into the valve guide. It would also be a fiddle on a hardened valve stem, so one doesn't bend it. No, fix the problem, don't add another. Or are you proposing the tighten the valve guides by knurling the outside? Then you will be removing block material when you push it back in, making it harder when new guides are fitted. Nup, to much "bush mechanic" stuff for me. Edited September 17, 2016 by Spinneyhill (see edit history) Link to comment Share on other sites More sharing options...
tom_in_nh Posted September 17, 2016 Share Posted September 17, 2016 1 hour ago, Spinneyhill said: I would imagine the rough knurled surface would be very good at grinding away inside the end of the valve guide. It would be a fiddle getting the knurling just deep enough that the material pushed up still fits into the valve guide. It would also be a fiddle on a hardened valve stem, so one doesn't bend it. No, fix the problem, don't add another. Spinneyhill, what are you talking about? Reading your post, it comes across to me that you believe that the outside diameter of the valve gets knurled. Is that what you are conveying? If so, that is not what you do. The inside diameter of the valve guide gets knurled, followed up by the burnishing / reaming to size. Pretty common procedure back in the day.... Link to comment Share on other sites More sharing options...
tom_in_nh Posted September 17, 2016 Share Posted September 17, 2016 Spinneyhill, I see that you have edited your post to include the knurling of the outside diameter of the valve guides. I now know for sure that you are not familiar about this knurling procedure. Please stop with your opinions on this matter, your lack of knowledge on this subject is sticking out like a sore thumb. Trying to be graceful about this, to spare you further embarrassment. Link to comment Share on other sites More sharing options...
DonMicheletti Posted September 18, 2016 Share Posted September 18, 2016 The issue of sticking valves has been around forever. That is how "Marvel Mystery Oil" came about. It is very unlikely that modern fuels are an issue - I think it is a red herring. Link to comment Share on other sites More sharing options...
Spinneyhill Posted September 18, 2016 Share Posted September 18, 2016 4 hours ago, tom_in_nh said: Spinneyhill, I see that you have edited your post to include the knurling of the outside diameter of the valve guides. I now know for sure that you are not familiar about this knurling procedure. Please stop with your opinions on this matter, your lack of knowledge on this subject is sticking out like a sore thumb. Trying to be graceful about this, to spare you further embarrassment. tom_in_nh, thanks for the graceful education. Clearly I am ignorant. I only ask you to educate me. I didn't know (or imagine) you could knurl inside a valve guide. Sorry I am the only one stupid enough to say something. What sort of tool do you use? Maybe I should have asked what on earth you are talking about - I am a Geotechnical Engineer, not a machinist or motor mechanic or anything else familiar with motor repair techniques, other than my own bumbling attempts to keep a 1930 vehicle going and in good repair. Everyone is entitled to an opinion, even the ill-informed. Link to comment Share on other sites More sharing options...
tom_in_nh Posted September 18, 2016 Share Posted September 18, 2016 OK, now we can move on. In a nutshell, the tool used to do the major operation of the valve guide knurling acts like a thread roll tap. It merely displaces metal in order to close up the bore of the worn out valve guide. You then use another tool to bring the size of the bore back into tolerance, so the valve can fit. The resulting repair has perhaps 30 - 40 spiral grooves in which oil can fill inside. Thus the long term lubrication, instead of the potential of a dry bore prone to rusting up. Capisce, yet? There are folks that will say this is a half assed repair, instead of guide replacement. It is a cheap and fast method that was common back in it's day. Obviously there is a limit on how worn the guides should be in order for this fix to be successful. It is simply another alternative that could help with valves rusting up over time. Hope this helps. Link to comment Share on other sites More sharing options...
DonMicheletti Posted September 18, 2016 Share Posted September 18, 2016 Not only knurling valve guides, but knurling pistons was common too. Link to comment Share on other sites More sharing options...
Vila Posted September 18, 2016 Share Posted September 18, 2016 (edited) When I had the cylinder head rebuilt for my 1933 Chevrolet Master back around 1976, the machine shop knurled the valve guides and installed the NOS Chevrolet valves I provided. The rebuild was done by a shop that specialized in farm tractors. The gentleman doing the rebuild had worked in the same shop for over 40 years and said he thought knurled guides were better than un-knurled new guide for the oil lubricating reason mentioned by Tom, as long as the guides did not have excessive wear. I reinstalled the head and the engine has been running great for the past 40 years. Edited September 18, 2016 by Vila (see edit history) Link to comment Share on other sites More sharing options...
trimacar Posted September 18, 2016 Share Posted September 18, 2016 19 hours ago, DonMicheletti said: The issue of sticking valves has been around forever. That is how "Marvel Mystery Oil" came about. It is very unlikely that modern fuels are an issue - I think it is a red herring. It's not the new gas that's the issue, it's gas that's been sitting in a tank for a couple of years. In other words, it's "aged" new gas, and there's no red herring about it, it will go bad, your car may not start, the fuel tank will get deposits in it, and in some instances it will cause damage to the engine. I don't know how to make you believe that if you haven't seen it, but in the last ten years, I've seen numerous issues with "new" aged gas, or "aged" new gas, however you want to say it...... Link to comment Share on other sites More sharing options...
alsancle Posted September 18, 2016 Author Share Posted September 18, 2016 I agree pump gas will gum everything up in short order but this car has never had pump gas in it while I have owned it. Either Cam-2 or AV. I'm wondering if the high octane AV gas does not have enough lubricants and does evaporate quickly. I do not think it was moisture but maybe it was. Link to comment Share on other sites More sharing options...
Spinneyhill Posted September 18, 2016 Share Posted September 18, 2016 (edited) I have read around a bit. Sticking valves are apparently caused by a buildup of carbon and that occurs because the valve guide and valve stem are worn, allowing the valve head to wobble about a tiny amount, meaning it doesn't seat cleanly all the time. Carbon builds up in the excess space. Now I know, I am thinking hard about my own car which has one sticky valve. It has a sloppy piston in No. 5 (skirt has been expanded) and sticky valve in No. 6, plus the occasional odd noise from the timing chain area and the BE bearings aren't wonderful. Maybe it is overhaul time. Edited September 18, 2016 by Spinneyhill (see edit history) Link to comment Share on other sites More sharing options...
Larry Schramm Posted September 19, 2016 Share Posted September 19, 2016 (edited) The ethanol in the gas acts as a good cleaner for the fuel system if you drive a couple of tanks of gas through the car. Alcohol is a good solvent for varnish. Edited September 19, 2016 by Larry Schramm (see edit history) Link to comment Share on other sites More sharing options...
DonMicheletti Posted September 19, 2016 Share Posted September 19, 2016 Has anyone had valves stick that can positively be attributed to just the fuel? Link to comment Share on other sites More sharing options...
c49er Posted September 19, 2016 Share Posted September 19, 2016 (edited) I have and have seen and dealt with several instances of it. Not a good situation. Never start an engine on varnished fuel!!!! Edited September 19, 2016 by c49er (see edit history) Link to comment Share on other sites More sharing options...
Spinneyhill Posted September 19, 2016 Share Posted September 19, 2016 (edited) Are your stuck valves all exhaust? My one is. With our high octane fuels (compared to 1930) that burn more slowly than the old low octane stuff did, I would have thought it might still be pretty hot or even just finishing burning as it went out, so why does the carbon get deposited and not burn off? We have no ethanol in our fuel so that can't be blamed. I am running 91 pump octane, the lowest available. Edited September 19, 2016 by Spinneyhill (see edit history) Link to comment Share on other sites More sharing options...
C Carl Posted September 19, 2016 Share Posted September 19, 2016 Re : exhaust temp. You are correct. EGT goes up when using significantly higher octane than spec'd. We were warned in flight engineers school not to expose the old recips still rarely used commercially at the time to prolonged running on higher octane av gas. It could result in burned ex valves in those complex old radials. - Carl ------------- What the h................. ? Uh , wait a minute. Wait a minute , here. Higher octane AV gas over lower octane automotive gas ? Hmmmmmmmm. Hmmmmmmmmm...... I was about to post this when lightning struck. Is there some clue here ? I don't think I am qualified to answer this , but I have done some things I thought clever at the time that in the end didn't.............. Are we/am I missing something here ? Hmmmmmmmm................. ????? Link to comment Share on other sites More sharing options...
C Carl Posted September 19, 2016 Share Posted September 19, 2016 The more I think about it , the less likely it seems. Still................. - Carl Link to comment Share on other sites More sharing options...
trimacar Posted September 19, 2016 Share Posted September 19, 2016 9 hours ago, DonMicheletti said: Has anyone had valves stick that can positively be attributed to just the fuel? Absolutely. The valves in my 1967 Lincoln Continental were locked up by old, gummed up, varnish, fuel that was in the tank. No ifs, ands, or buts..... I thought the tank was empty but it had a concentrated layer of old gas, the new gas I put in dissolved enough of the gums, I ran the car for the first time about 30 minutes and it ran fine. Went to start it the next day, the valves were locked in place by the gums, to the extent they had to be driven out of the guides with a hammer.... Here's an interesting read, by a fuels expert. I'll post part of it, for those who don't want to read the whole thing. In the article he states that even 100LL (100 octane low lead) Avgas will form gums that can affect an engine. "But what limits the life of a fuel? One problem is evaporation of light ends in the fuel. This is a concern with small engines, especially 2-strokes, and may make it almost impossible to start. I have a 2-cycle dirt bike, and if it sits for a month or two, I have to put fresh gasoline in and drain the carb to get it to start. But the major concern with aging fuels is gum formation. Over time, heavy ends and additives can start to form gums, which can plug up or, dare I say, “gum-up” a carburetor or fuel system. This can lead to bad fuel distribution or even an engine stall." http://generalaviationnews.com/2011/01/09/how-long-can-fuel-be-safely-stored/ Link to comment Share on other sites More sharing options...
Airy Cat Posted September 23, 2016 Share Posted September 23, 2016 I have used Lucas Upper Cylinder Lubricant and added 5 gallons on AV Gas to my fuel tanks for many years now with no adverse effects. Link to comment Share on other sites More sharing options...
jp928 Posted September 23, 2016 Share Posted September 23, 2016 I dont like the idea of idling an engine to warm in a garage queen. With my queen, I make a point of doing at least 20+ miles on any use, preferably with some high throttle time now and again. It can take quite a while for the whole drive train to get properly hot, and more to the point, actual driving will warm things up a lot quicker than idling. No, this doesnt apply to the Rover, its not on the road yet. jp 26 Rover 9 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now