Devjas Posted August 17, 2018 Share Posted August 17, 2018 Asking for help...I want my tire jack to look correct in my trunk..I found the original hook and spring but don’t know how it’s put in place. Any photos of the correct setup would be greatly appreciated... Link to comment Share on other sites More sharing options...
Riviera63 Posted August 17, 2018 Share Posted August 17, 2018 10 hours ago, Devjas said: Asking for help...I want my tire jack to look correct in my trunk..I found the original hook and spring but don’t know how it’s put in place. Any photos of the correct setup would be greatly appreciated... This is a shot of my 63. I assume 65 is the same. Hope this helps. Bill 2 Link to comment Share on other sites More sharing options...
Seafoam65 Posted August 17, 2018 Share Posted August 17, 2018 (edited) I studied a lot trunk compartments and this is what I decided was best...... I have my jack flipped over so the ugly protruding handle socket doesn't show. The forward and backward position of the black center section of the jack seems to look best the way I have mine. There has been much discussion about the jack handle previously on the forum. I've studied a lot of trunks and most of them have the handle as shown, between the spring and the cardboard. Some have said that it goes under the spare tire towards the front of the trunk tray, but I couldn't get mine to fit up there no matter how hard I tried. Everyone I 've talked to agrees that the handle was not strapped to the jack from the factory, although it looks very nice that way. Edited August 17, 2018 by Seafoam65 (see edit history) 1 Link to comment Share on other sites More sharing options...
Devjas Posted August 17, 2018 Author Share Posted August 17, 2018 Thanks to both Seafoam and Bill for you pics. It's exactly what I needed to see. Now I can put it all together. I really like the way Bill attached the tire iron to the arm... How is it attached? Tape? Velcro? Link to comment Share on other sites More sharing options...
Seafoam65 Posted August 17, 2018 Share Posted August 17, 2018 (edited) I believe what you are seeing is a couple of strips cut from a bicycle tire inner tube holding the jack handle in place, or some type of super heavy duty rubber bands. Edited August 17, 2018 by Seafoam65 (see edit history) 1 Link to comment Share on other sites More sharing options...
RivNut Posted August 17, 2018 Share Posted August 17, 2018 Here are a couple of pictures that show how the braces in the trunk are cut so that the jack will only orient itself one way if installed correctly. A skinny bicycle inner tube cut into a couple of sections works well for supporting the jack handle. When driving, and not parked for shows, you can also wedge the jack handle between the spare tire and the trunk floor. On the top of the wheel well On the floor of the trunk 2 Link to comment Share on other sites More sharing options...
Devjas Posted August 17, 2018 Author Share Posted August 17, 2018 Interesting, thanks for the info..... 1 Link to comment Share on other sites More sharing options...
Riviera63 Posted August 17, 2018 Share Posted August 17, 2018 (edited) 1 hour ago, Devjas said: Thanks to both Seafoam and Bill for you pics. It's exactly what I needed to see. Now I can put it all together. I really like the way Bill attached the tire iron to the arm... How is it attached? Tape? Velcro? I tried the bicycle inner tube and did not like the fit nor the look. I found and used black velcro straps. I think it looks more finished, it holds the tire iron very tightly to the jack and they are easy to remove and put on without taking out the jack. Bill P.S. I did put rubber tubing on both ends of the jack where it rests in the V-shaped brackets that were pictured by Ed. It keeps it from rattling and also keeps the jack from getting nicked up by the bracket. You can see it on the lower end in my picture. Edited August 17, 2018 by Riviera63 revise text (see edit history) 2 Link to comment Share on other sites More sharing options...
Pat Curran Posted August 17, 2018 Share Posted August 17, 2018 If you are having the car judged at a BCA show, make sure the jack handle is visible. I had stuffed mine up with the spare tire to keep it from sliding around and forgot about it...........and got dinged. Lesson learned and never repeated! 1 Link to comment Share on other sites More sharing options...
RivNut Posted August 17, 2018 Share Posted August 17, 2018 You might consider taking a piece of a fairly thick vacuum hose, splitting it lengthwise, and slipping it over the edges of the brackets. No need to remove anything when taking the jack out of its resting place. 1 Link to comment Share on other sites More sharing options...
PWB Posted August 17, 2018 Share Posted August 17, 2018 Say, Mr Bill The next time the wife throws me to the dog house, may I crash in that beautiful trunk? Link to comment Share on other sites More sharing options...
Riviera63 Posted August 18, 2018 Share Posted August 18, 2018 46 minutes ago, PWB said: Say, Mr Bill The next time the wife throws me to the dog house, may I crash in that beautiful trunk? As long as you take your shoes off and you have to bring your own pillow. Link to comment Share on other sites More sharing options...
Devjas Posted August 18, 2018 Author Share Posted August 18, 2018 All done.. Thanks for all you comments and pics... what do you think? 2 Link to comment Share on other sites More sharing options...
KongaMan Posted August 18, 2018 Share Posted August 18, 2018 30 minutes ago, Devjas said: All done.. Thanks for all you comments and pics... what do you think? I think some golfer is missing his pants. 2 Link to comment Share on other sites More sharing options...
Zimm63 Posted August 18, 2018 Share Posted August 18, 2018 What is the preferred source for the spring? Link to comment Share on other sites More sharing options...
RivNut Posted August 18, 2018 Share Posted August 18, 2018 1 hour ago, Zimm63 said: What is the preferred source for the spring? Ace Hardware Link to comment Share on other sites More sharing options...
Zimm63 Posted August 19, 2018 Share Posted August 19, 2018 OK, some confusion here. What is the look hanging off the jack? At first glance it appears to be part of the spring, according to my new progressive glasses (trying not to hate them). Closer examination shows that not to be the case. The spring is just a spring, from what I see now. Quote Link to comment Share on other sites More sharing options...
RivNut Posted August 19, 2018 Share Posted August 19, 2018 1 hour ago, Zimm63 said: OK, some confusion here. What is the look hanging off the jack? At first glance it appears to be part of the spring, according to my new progressive glasses (trying not to hate them). Closer examination shows that not to be the case. The spring is just a spring, from what I see now. I think those refering to the looked wire, it's a handle used to stretch the spring so you can take it off. Link to comment Share on other sites More sharing options...
gungeey Posted August 20, 2018 Share Posted August 20, 2018 Heres my jack set up, about 30lbs of confidence 3 Link to comment Share on other sites More sharing options...
Zimm63 Posted August 20, 2018 Share Posted August 20, 2018 I have a very similar jack in my trunk. Picking up the Riv with the stock jack is not on my list. Given that it is rickety as all hell coupled with what I paid Tri City to replate that bumper, the original jack is an ornament. Period. 2 Link to comment Share on other sites More sharing options...
NC1968Riviera Posted August 21, 2018 Share Posted August 21, 2018 On 8/17/2018 at 9:00 PM, KongaMan said: I think some golfer is missing his pants. Ha, I was thinking the same thing. Great looking trunk though! Congrats! Link to comment Share on other sites More sharing options...
MikeJS Posted August 25, 2018 Share Posted August 25, 2018 Good day. Great info here on properly mounting the jack and handle, thanks. I'm just doing the trunk in my '64, and was wondering if someone can share photos of how the other two parts of the jack, (the base and the big hook thingy) are properly factory mounted. I have the spare tire half-cover and a mounting bracket on the shelf, but I don't have any hardware to actually fix the tire to the bracket on the shelf. I assume that the jack base is bolted to the rim somehow, but where would the jack's hook go? Any advice on the acquiring (or DIY fabricating) the mounting hardware would be greatly appreciated. Later, Mike Swick Edmonton, AB ---- Link to comment Share on other sites More sharing options...
RivNut Posted August 25, 2018 Share Posted August 25, 2018 Can you post a picture of the jack's "hook?" The jack for a first generation Riviera has no hook. The tab on the jack goes into a slot on the bumper. I'm thinking you don't have the correct jack. As I said, just thinking. Or are you referring to the hold down "J" bolt? The picture in post #8 is inclusive. Link to comment Share on other sites More sharing options...
Riviera63 Posted August 25, 2018 Share Posted August 25, 2018 48 minutes ago, MikeJS said: Good day. Great info here on properly mounting the jack and handle, thanks. I'm just doing the trunk in my '64, and was wondering if someone can share photos of how the other two parts of the jack, (the base and the big hook thingy) are properly factory mounted. I have the spare tire half-cover and a mounting bracket on the shelf, but I don't have any hardware to actually fix the tire to the bracket on the shelf. I assume that the jack base is bolted to the rim somehow, but where would the jack's hook go? Any advice on the acquiring (or DIY fabricating) the mounting hardware would be greatly appreciated. Later, Mike Swick Edmonton, AB ---- As Ed said go to post #8 for how to mount the jack along the side. I have attached pictures of my half cover mounted on the tire and the hardware you need to fix the tire to the rear shelf. I hope this helps. The hardware to affix the jack to the trunk and to affix the spare to the rear shelf should be readily available from any number of the vendors that advertise in the Riview. Bill Link to comment Share on other sites More sharing options...
MikeJS Posted August 25, 2018 Share Posted August 25, 2018 44 minutes ago, RivNut said: Can you post a picture of the jack's "hook?" The jack for a first generation Riviera has no hook. The tab on the jack goes into a slot on the bumper. Doh!!! To be honest, this hunk of metal in the trunk has been there since I've owned the car, and so I just assumed it was part of the original jack. I don't recall ever having a flat, and ever just used a floor jack. A quick test of the jack, it seems to fit the slots, and seems to fit the mounting brackets so can I assume the jack is correct and I can get rid of that dead weight hook??? If correct jack, does the base mount on the spare? Later, Mike Swick Edmonton, AB ---- Link to comment Share on other sites More sharing options...
MikeJS Posted August 25, 2018 Share Posted August 25, 2018 15 minutes ago, Riviera63 said: I hope this helps. Great stuff, thanks, Bill. That's what I need to see. Should be an easy DIY fix...of sorts... Later, Mike Swick Edmonton, AB ---- Link to comment Share on other sites More sharing options...
Riviera63 Posted August 25, 2018 Share Posted August 25, 2018 Yes, the base is used to hold down the spare on the rear shelf. Look at the 2nd picture I posted up above. Bill Link to comment Share on other sites More sharing options...
RivNut Posted August 25, 2018 Share Posted August 25, 2018 The big hook is not part of a 1st generation Riviera jack. Looking closer at the jack, I don't think it's a Riviera jack either. Luckily you haven't had to use it. ? Link to comment Share on other sites More sharing options...
MikeJS Posted August 26, 2018 Share Posted August 26, 2018 19 hours ago, RivNut said: Looking closer at the jack, I don't think it's a Riviera jack either. Thanks, Ed, I think you're right that this isn't the correct jack. The post is actually a square tube, and from the picture Bill posted (post 24), the base of the jack appears to have a triangular shape. Tough to tell in most pictures, but the support post does look decidedly different than mine. couldn't figure out why the support brackets in the trunk have a triangular cut out for a square tube even though when I put it in the brackets it sits very solid... (Once again... doh!!!) Oh, well, at least now I know right from wrong, and I now have another correct part on my list to try to find... Thanks again, for the input, much appreciated. Later, Mike Swick Edmonton, AB ---- Link to comment Share on other sites More sharing options...
1965rivgs Posted August 27, 2018 Share Posted August 27, 2018 13 hours ago, MikeJS said: Thanks, Ed, I think you're right that this isn't the correct jack. The post is actually a square tube, and from the picture Bill posted (post 24), the base of the jack appears to have a triangular shape. Tough to tell in most pictures, but the support post does look decidedly different than mine. couldn't figure out why the support brackets in the trunk have a triangular cut out for a square tube even though when I put it in the brackets it sits very solid... (Once again... doh!!!) Oh, well, at least now I know right from wrong, and I now have another correct part on my list to try to find... Thanks again, for the input, much appreciated. Later, Mike Swick Edmonton, AB ---- Mike, The Rivs were supplied with both a triangular solid shaft version and a square tube. Each jack was made by a different supplier. Both jacks are specifically listed in the parts book and identified by supplier along with their specific base. Cross it off your list...LOL, Tom Mooney Link to comment Share on other sites More sharing options...
MikeJS Posted August 28, 2018 Share Posted August 28, 2018 (edited) 20 hours ago, 1965rivgs said: The Rivs were supplied with both a triangular solid shaft version and a square tube. Each jack was made by a different supplier. Both jacks are specifically listed in the parts book and identified by supplier along with their specific base. Cross it off your list...LOL, Tom, good day, much appreciated.... based on what I've learned from my short time on this forum, I'll take YOUR word for it... thanks. For what it's worth, I spent a bit of time on the net, and although jacks, etc have been discussed in this ROA forum on numerous occasions, I didn't see anything along these specific lines. What I did find on the 'net was some google book references related to Chevelles, and the GTO... From the Chevelle "Restoration Guide (edited for brevity) "... "three different racks were used: a t-shape rack... a rounded keystone shape rack... and a square rack"... similar text in the GTO, but no reference to the square rack. Although it can be tough to tell, it appears that the most common "Riviera-jack" was the a rounded keystone shape rack. [EDIT: Re-read Tom's reply- most common for Riv. is t-shape...??] There is/was a gentleman that appears to have dedicated a significant amount of time of his life on this subject trying to nail down the "correct jack" for Camaros that wrote... " "The more common keystone cross sectional tube jacks made by the Universal Tool Co. (stamped "UN" on the up-down lever with a 2-digit date code stamped on the RIVET HEAD". He has listed the various manufacturers (Universal, Walker Manufacturing Co. Auto Specialties Co. and Ryerson & Haynes, and how they mark their jacks.) My jack has no discernible markings whatsoever, 34" long, and again, fits pretty tight in the brackets. Does a known stock factory Riv-jack have any markings? In another on-line discussion related to Chevelles, apparently the plant that the car was made at could be equipped with either the 'hollow' or 't-post'. Both Baltimore and Flint used the hollow and Kansas used the t-post. Again, this is Chevelle, and I'm not sure which rack they are referring to as 'hollow'. but I suspect all various GM brands could/would procure parts from various vendors in different regions, thus various designs, as long as it met the hook mechanism and capacity specs. My Riv' came outta Flint, sold at a dealer here in Edmonton Canada. ("Ya, ship those crappy jacks to Canada, they'll never know the difference...?) Nonetheless, I appreciate the input. My car's never gonna be judged by anyone but me, but I always like to know the "rules" before I bend 'em... And although I have no fear in using a bumper jack for safety reasons, with my luck, I could see myself roadside with flat tire, AND my bumper laying on the ground, and me with a broken leg from trying to kick myself in the ass... . Seriously, tho' I will be looking at some other form of emergency jack to keep in the car that's been discussed elsewhere in the forum... Thanks again, guys, much appreciated. Later, Mike Swick Edmonton, AB ----- Edited August 28, 2018 by MikeJS (see edit history) Link to comment Share on other sites More sharing options...
1965rivgs Posted August 28, 2018 Share Posted August 28, 2018 Mike, This is the page out of the `65 parts book which describes the jacks. You will notice, although there are 2 bases described, there is only one listing for the actual jack. But...there are quite a few jack part numbers listed in the descriptions of the two different bases. I didnt take the time to examine all the listed part numbers (I did this as a little research project 3 or more decades ago) but take my word for it, I have owned many `65`s and they have been equipped with two different style jacks. Maybe one particular style was not available as a service part or perhaps Buick just mistakenly omitted it from the parts book? You will notice I have notes in the margin. These notes are based on actual part numbers which appear on paper tags on the original components which I noted based on cars in the fleet. If one has a car which is in original and decent shape in the trunk area these paper part tags, with numbers, usually hold up pretty well. Hope this helps, Tom Mooney 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now