mribbich@wi.rr.com Posted November 19, 2019 Share Posted November 19, 2019 How do you remove the inside door handles on a 1936 Chevrolet???? Thank You!!! 1-262-392-2989 or mribbich@wi.rr.com Marv. Link to comment Share on other sites More sharing options...
playswithbrass Posted November 19, 2019 Share Posted November 19, 2019 There is a horse shoe looking wire clip that is in a groove in the handle but hidden by the escutcheon plate. Pushing the plate away from the handle will reveal the fastener ,this was used well into the 1980,s hope this helps 1 Link to comment Share on other sites More sharing options...
keiser31 Posted November 19, 2019 Share Posted November 19, 2019 I have been able to hook it with a bent paper clip. Link to comment Share on other sites More sharing options...
Guest Posted November 19, 2019 Share Posted November 19, 2019 Somewhere in the 30's the clips were made a little larger, I am not sure when. These tools are available in both sizes. I never tried a Paperclip as Keiser31 has suggested but have used an ice pick. Link to comment Share on other sites More sharing options...
Bloo Posted November 19, 2019 Share Posted November 19, 2019 I have had zero luck with the "slide it under" tool shown on my Pontiac (although it works fine on newer GM products). My Pontiac has literally the same door handles and bezels shown in the pics above. I like the paper clip idea, or a pick if you can make enough room to get it in. The trick is you need to hook one end and roll the clip sideways to get it out. The clip looks like Tinindian's pic. The clip is between the black bezel and the chrome handle. There is a tool with a c-shaped slot in the side to roll the clip out, but I could not find a pic online. I couldn't find my tool either. Hey mribbich@wi.rr.com, those doors look pretty solid! Are the bottoms there? More to the point does that car have back doors? Are the bottoms still in those? I would love to see some pictures if so. Link to comment Share on other sites More sharing options...
chistech Posted November 19, 2019 Share Posted November 19, 2019 (edited) 1 hour ago, Bloo said: I have had zero luck with the "slide it under" tool shown on my Pontiac (although it works fine on newer GM products). My Pontiac has literally the same door handles and bezels shown in the pics above. I like the paper clip idea, or a pick if you can make enough room to get it in. The trick is you need to hook one end and roll the clip sideways to get it out. The clip looks like Tinindian's pic. The clip is between the black bezel and the chrome handle. There is a tool with a c-shaped slot in the side to roll the clip out, but I could not find a pic online. I couldn't find my tool either. Hey mribbich@wi.rr.com, those doors look pretty solid! Are the bottoms there? More to the point does that car have back doors? Are the bottoms still in those? I would love to see some pictures if so. The reason the tool doesn’t work is the tools they sell are for the more modern, larger c clips. The handles and clips were specifically designed that the open ends of the clips face the long length of the handle or crank. I’ve taken a old hack saw blade and ground a “V” notch in the end. Slip the blade between the escutcheon top and the handle hub, staying parallel with the handle. Remember, you want to push the blade in from the end of the handle or crank towards the hub. The thin blade with the sharp groove ground in it will hook one side of the clip and push/rotate it out of the handle. Push in on the handle center towards the door slightly to remove any pressure off the clip. Many handles have a stiff any rattle spring in the center to put pressure on the clip. Another thing is sometimes the white metal handles corrode and the clips get stuck in the groove making it somewhat of a chore to get the clip out. I have removed hundreds of handles this way. Edited November 19, 2019 by chistech (see edit history) 2 Link to comment Share on other sites More sharing options...
Bloo Posted November 19, 2019 Share Posted November 19, 2019 I have tools for 2 sizes..... It didn't work on those cranks like in the picture because the groove the tool needs to slide through was not cut all the way like a later handle is. Past the tips of the clip, the groove just stops. There is no way for the tool to slide in. I like your hacksaw idea. 1 Link to comment Share on other sites More sharing options...
The 55er Posted November 19, 2019 Share Posted November 19, 2019 (edited) I've had good results with this pliers-type tool to remove those smaller GM clips. Edited November 19, 2019 by The 55er added pics (see edit history) 3 Link to comment Share on other sites More sharing options...
mike6024 Posted November 19, 2019 Share Posted November 19, 2019 I take a piece of wire. Bend just the very tip into a tiny hook. The hook at the end is just about 1/8 th inch only. Bend it over so it is just a bit over 90 degrees. Slide it in, going in flat, get behind the clip, then rotate the wire 90 degrees so you snag the clip with the hook end, then pull it out. 2 Link to comment Share on other sites More sharing options...
chistech Posted November 19, 2019 Share Posted November 19, 2019 Here’s another tip on window crank handle knobs that don’t turn on the handle. When you find stuck knobs, in most cases it’s because the white metal has swelled enough to jam the bottom turned in edge of the knob. I run a xacto razor saw blade right around the joint, removing the swollen metal and often some corrosion that is in that joint. 2 Link to comment Share on other sites More sharing options...
mribbich@wi.rr.com Posted November 23, 2019 Author Share Posted November 23, 2019 Thank!!! for all the ideas but I am still having no luck removing the clips. The door is sold and I want to remove the handles so they don't get broken in shipment. Marv. Link to comment Share on other sites More sharing options...
mike6024 Posted November 23, 2019 Share Posted November 23, 2019 Can you see the clips. with an LED flashlight, prying the escutcheon plate back? Do they look rusted? Link to comment Share on other sites More sharing options...
mribbich@wi.rr.com Posted November 23, 2019 Author Share Posted November 23, 2019 Yes I can see the clips will try some W-D 40 or rust buster to see that helps. Thanks!! Marv Link to comment Share on other sites More sharing options...
dalef62 Posted November 23, 2019 Share Posted November 23, 2019 Are you sure there isn't a pin going through the handle? I recall on my 41 Olds that it had a pin that goes through the base of the handle and the escussion and coil spring keeps it in place? Link to comment Share on other sites More sharing options...
mribbich@wi.rr.com Posted November 23, 2019 Author Share Posted November 23, 2019 Just the clip. Thanks for asking!!! Marv Link to comment Share on other sites More sharing options...
dalef62 Posted November 23, 2019 Share Posted November 23, 2019 Can you get a picture of the offending clip?? Link to comment Share on other sites More sharing options...
mribbich@wi.rr.com Posted November 23, 2019 Author Share Posted November 23, 2019 It is the same as was posted earlier by Tinindian Marv. Link to comment Share on other sites More sharing options...
mike6024 Posted November 23, 2019 Share Posted November 23, 2019 On 11/18/2019 at 7:55 PM, The 55er said: That tool would appear to grab the clip, then you pull it out. But it does not seem that the tool would spread the clip and open it up. So it seems less than ideal. Link to comment Share on other sites More sharing options...
mike6024 Posted November 23, 2019 Share Posted November 23, 2019 I think you either need to make a hook, and pull it out. Grab with the hook at the back, curved part of the clip. Or make a custom tool from a piece of scrap metal to push it out. Push against one of the tips of the clip. Push against one of the tips and get it part way off, then push against the other tip. The tool would be something like a slot screwdriver, but with a notch filed in the tip, so it can push the tip of the clip, without slipping off. Link to comment Share on other sites More sharing options...
Bloo Posted November 23, 2019 Share Posted November 23, 2019 It needs to be much flatter though. There is usually no room for screwdrivers. The bakelite escutcheons also like to break, and are harder to find than handles. Link to comment Share on other sites More sharing options...
JFranklin Posted November 24, 2019 Share Posted November 24, 2019 I believe the clip is pushed out from the open end. It will expand and pop off. I have both tools but don't remember which I used. Link to comment Share on other sites More sharing options...
Vila Posted November 24, 2019 Share Posted November 24, 2019 There may be a spiral shaped spring behind each escutcheon that would have pressed the interior door panel out against the escutcheon and handle so the door panel would not flex to reveal any gaps. Link to comment Share on other sites More sharing options...
Bloo Posted November 24, 2019 Share Posted November 24, 2019 Yes, there is. You have to get between the bakelite escutcheon and the cast handle. The spring you refer to makes it a challenge. Link to comment Share on other sites More sharing options...
chistech Posted November 25, 2019 Share Posted November 25, 2019 It sounds like the pot metal has corroded some and the clip is stuck in the groove. You can use a long thin bladed flat screwdriver and push on one ear of the clip. When they’re stuck in the groove, pushing on the one side will roll the clip out. As I mentioned before, there’s a good chance there’s a stout spring in the center of the handle post pushing out on the handle. This spring will also make the clip hard to pull out. Tap down on the center of the handle with a rubber mallet. Often this will loosen the clip up in groove. 1 Link to comment Share on other sites More sharing options...
markr1001 Posted March 4, 2020 Share Posted March 4, 2020 use a terry cloth rag. it will catch it and pull it off easily 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now