Barney Eaton Posted January 18, 2013 Share Posted January 18, 2013 Thanks to the article I wrote about rebuilding power antennas in the ROA magazine last year, I am seeing (rebuilding) more early antenna. I want to thank those that have sent me antenna.The reason for this post is to clarify the differences that I have found. I don't own a Riviera so my reference library is small on the car. The article was done to cover the 1980 to present GM power antennas. Prior to 1980 GM used power antenna from Tenna Corp in Cleveland OH. Tenna stopped making antennas sometime in the early '80's.I have lots of experience with the 1980 and newer Delco antenna, and can repair and replace almost anything broken on them. However the Tenna antenna can be a problem because of replacement parts availabity. If you have one that is not working, I will try and help but it all depends on what is wrong with it. Over the holidays I did a 1965 Riv antenna and discovered while cleaning the parts that 2 of the 4 reduction gears were stripped. The customer happened to have a couple of extra antenna, so I was able to use parts from the other antenna to make one good one.The '63-65 Riv antenna can be a problem because the mast does not fully retract into the fender, there is some 4-6 inches out of the fender when it is lowered. If the part sticking out is bent, the only replacement part I have found is another '63-'65 mast. The motor end of all the Tenna antenna is pretty much the same from '63 to '79. The differences in power antenna is the mast part inside the fender. Various cars had different clearance requirements so the section of the antenna you cannot see will vary in length and the upper mounting brackets. I am attaching a photo of some early power antenna that shows the different under fender mounting arrangements.Thanks again for sending me antennas and I am happy to work with anyone that has a power antenna problem. 1 Link to comment Share on other sites More sharing options...
Guest Jimmys 63 Posted September 18, 2013 Share Posted September 18, 2013 Hey Barney, I have a '63 Riviera, the power antenna worked sometimes and not others. I have power to the switch and power out of the switch but now doesnt work up or down. There are only two wires to the antenna, am I right in assuming that the hot and ground alternate wires to produce up and down motion? I jumped a hot and ground wire to the antenna and nothing happens. Bad antenna motor? Thanks Jimmy Link to comment Share on other sites More sharing options...
1965rivgs Posted September 18, 2013 Share Posted September 18, 2013 Ground the motor body and apply voltage to either wire. Voltage to wire #1 makes the motor raise the antenna mast and voltage to wire #2 lowers the antenna mast. Tom Mooney Link to comment Share on other sites More sharing options...
68RIVGS Posted September 18, 2013 Share Posted September 18, 2013 Over the years, most of the problems with the early 'Tenna style' power antennas (...other than obvious broken cable, bent mast sections, or electrical gremlins), is a build up of 'crud and corrosion' with age and time, in the lower cable storage area. These units have crimped flanges, and were not really designed to be taken apart easily - with some tender persuasion, and a little determination, these units can be brought back to life with a complete disassembly and a good cleaning of the lower cable housing, including the nylon cable attatched to the upper sedtion of the antenna mast. Proper adjustment and lubrication of the electric motor 'ball-clutch-unit' can be accomplished at the same time. The info in the Shop Manual will also help in repair or overhaul of a power antenna. Always 'bench test' a unit prior to installation in the car to ensure it functions OK, as it's no fun doing the same job twice !! Link to comment Share on other sites More sharing options...
Barney Eaton Posted August 29, 2014 Author Share Posted August 29, 2014 I am still repairing GM power antenna. Thanks to the Riviera Club, I have repaired several '63-'65 antennas. The problem is spare parts, if your antenna mast are in good shape, I have motor parts. As noted above, most of the problem is age and lack of use. The grease in the gear reduction on the pre '80 antennas gets hard. I have seen a few stripped gears, but disassembly, cleaning, lube and servicing the motor put most of them back into service. I also have a fixture to straighten bowed antenna mast. Most can be saved unless they are kinked or broken off and I have no supply of replacement mast. Some mast listed on Ebay are twice the price I charge to repair antennas. Clarks Corvair parts sells the black plastic part that is at the top of the fender on the early Riviera, they get around $26 plus shipping for them.Let me know if I can help you with an antenna problem. 1 Link to comment Share on other sites More sharing options...
JZRIV Posted August 29, 2014 Share Posted August 29, 2014 Thanks for the update Barney. You are providing a valuable service to Riviera owners. Link to comment Share on other sites More sharing options...
Seafoam65 Posted August 29, 2014 Share Posted August 29, 2014 I am still repairing GM power antenna. Thanks to the Riviera Club, I have repaired several '63-'65 antennas. The problem is spare parts, if your antenna mast are in good shape, I have motor parts. As noted above, most of the problem is age and lack of use. The grease in the gear reduction on the pre '80 antennas gets hard. I have seen a few stripped gears, but disassembly, cleaning, lube and servicing the motor put most of them back into service. I also have a fixture to straighten bowed antenna mast. Most can be saved unless they are kinked or broken off and I have no supply of replacement mast. Some mast listed on Ebay are twice the price I charge to repair antennas. Clarks Corvair parts sells the black plastic part that is at the top of the fender on the early Riviera, they get around $26 plus shipping for them.Let me know if I can help you with an antenna problem. Barney, let me tell you what my power antenna is doing and tell me if you think it is fixable.....the motor runs justfine, and the mast looks new and isn't bent, but when the motor runs the antenna stays where it is. In addition, I can manuallyadjust the mast up and down it's entire normal movement and it will stay where it is, just like it's a manual antenna. This antennais on my 65 Riviera. Of course it really isn't a problem since I can manually adjust it, but someday I would like to fix it if it is possible. Link to comment Share on other sites More sharing options...
RivNut Posted August 29, 2014 Share Posted August 29, 2014 The cable that winds up in the housing is probably broken. Replace it and you're probably good to go. Or let Barry fix it and you'll be sure it's good to go.Ed Link to comment Share on other sites More sharing options...
Seafoam65 Posted August 30, 2014 Share Posted August 30, 2014 The cable that winds up in the housing is probably broken. Replace it and you're probably good to go. Or let Barry fix it and you'll be sure it's good to go.Ed I've fixed a lot of antennas on later model 70's and up cars, usually when the plastic line breaks on the later model ones,you don't have full movement up and down on the mast or it is frozen and won't move at all. That's why I was thinking maybe a gear problem, but I've never seen the insides of a 65 model antenna so they may act differently.....by the way......who's Barry? LOL! Link to comment Share on other sites More sharing options...
RivNut Posted August 30, 2014 Share Posted August 30, 2014 Barry Eaton. Reatta guru. He's one of the valuable sources of information and parts for the 86 - 93 Rivieras. When Buick built the Reatta, they used a lot of Riviera technology on the Reatta so Barry has a lot of knowledge that transfers across models for those years. See post #5.Ed 1 Link to comment Share on other sites More sharing options...
Seafoam65 Posted August 30, 2014 Share Posted August 30, 2014 Barry Eaton. Reatta guru. He's one of the valuable sources of information and parts for the 86 - 93 Rivieras. When Buick built the Reatta, they used a lot of Riviera technology on the Reatta so Barry has a lot of knowledge that transfers across models for those years. See post #5.Ed Ed, I was pulling your leg......his name is actually Barney Eaton! Link to comment Share on other sites More sharing options...
RivNut Posted August 30, 2014 Share Posted August 30, 2014 DUH! Barney, Barry, Bennie, Barley, Baxter, Bernie, Meredith Baxter Birney. I knew who I meant, I thought you could read my mind. Thanks for catching that.Barney, I apologize.Ed Link to comment Share on other sites More sharing options...
Guest carkifelek Posted November 11, 2014 Share Posted November 11, 2014 (edited) Barney, I actually have a ’62 antenna. I have a small analog switch that I can use to control it. However, it operates on positive and negative voltage. That means that I can use positive voltage for making the antenna and negative voltage for lowering the antenna. However, the controller has only three terminals, I was wondering if I can use this analog switch to lower the antenna or to make it rise. pcb fabrication and assembly Edited September 21, 2015 by carkifelek (see edit history) Link to comment Share on other sites More sharing options...
MrEarl Posted November 20, 2014 Share Posted November 20, 2014 Barney, any interest in expanding into earlier year power antennae. like 54/55 maybe? Link to comment Share on other sites More sharing options...
Guest clamshells Posted November 20, 2014 Share Posted November 20, 2014 I sent Barney a box of parts including one very good but non-working 1st Gen antenna and a repro "plastic" and he sent me back one excellent and one very good antenna. Mind you I only expected one working antenna from the mess I sent him. Barney called and asked if I wanted two working antennas and for another 90.00 I have a back up on my shelf ;-). I highly recommend his service. Link to comment Share on other sites More sharing options...
J3Studio Posted November 24, 2014 Share Posted November 24, 2014 I sent Barney a box of parts including one very good but non-working 1st Gen antenna and a repro "plastic" and he sent me back one excellent and one very good antenna. Mind you I only expected one working antenna from the mess I sent him. Barney called and asked if I wanted two working antennas and for another 90.00 I have a back up on my shelf ;-). I highly recommend his service.I'm another satisfied customer - he did an absolutely gorgeous job for my 1985 Corvette. Link to comment Share on other sites More sharing options...
Guest viya0414 Posted August 19, 2017 Share Posted August 19, 2017 Ground the motor body and apply voltage to either wire. Voltage to wire #1 makes the motor raise the antenna mast and voltage to wire #2 lowers the antenna mast. Tom Mooney PCBA Assembly Link to comment Share on other sites More sharing options...
Jon Wayne Posted March 8, 2019 Share Posted March 8, 2019 Hey Barney Eaton, I had my mechanic take out my 64 Buick Riviera power antenna unit and he said, "its sort of working, I hear the motor running and could get the top 2 masts down but the last part seems to be stuck. Do you have a suggestion on how to provide maintenance to this assembly and or are you currently repairing these masts? Thanks JW Link to comment Share on other sites More sharing options...
RivNut Posted March 8, 2019 Share Posted March 8, 2019 (edited) How far up does it extend? The antenna on the first generation Rivieras does not go down flush with the fender. It sticks up 10"or so. This picture show a 64 with the antenna fully retracted. Edited March 8, 2019 by RivNut (see edit history) 1 Link to comment Share on other sites More sharing options...
Seafoam65 Posted March 8, 2019 Share Posted March 8, 2019 Ed meant to say "doesn't" go down flush with the fender. 1 Link to comment Share on other sites More sharing options...
RivNut Posted March 8, 2019 Share Posted March 8, 2019 2 hours ago, Seafoam65 said: Ed meant to say "doesn't" go down flush with the fender. I've edited that goof. Thanks Winston. Link to comment Share on other sites More sharing options...
psychostang Posted March 9, 2019 Share Posted March 9, 2019 Is Barney still around? Link to comment Share on other sites More sharing options...
RivNut Posted March 9, 2019 Share Posted March 9, 2019 I clicked on his avatar and it says that he last visited the forums 5 hours ago. 5 hours ago Link to comment Share on other sites More sharing options...
psychostang Posted March 10, 2019 Share Posted March 10, 2019 I have an antenna from my 65 , where the motor works but the mast doesn't move. Also the upper section of the mast is broken. I wonder if he can replace the mast? Link to comment Share on other sites More sharing options...
RivNut Posted March 10, 2019 Share Posted March 10, 2019 Send him a PM and ask him. Link to comment Share on other sites More sharing options...
Barney Eaton Posted March 10, 2019 Author Share Posted March 10, 2019 (edited) I am still around..........I can usually fix them. The only problem is replacement chrome mast, if yours is broken off or missing, kinked or dented, I cannot help as I have no extra masts. For that reason I have several owners send me 2 or 3 antenna, I take the best parts and make them one good one. My emai = Barney@texas.net should you want more info. Ed mentioned the '63-65 antenna extends 8 or so inches out of the fender when completely down. That makes them easy targets for damage. When the BCA meet was in Milwaukee a couple years back, I shot several pictures of antenna on "show" cars and there were some differences.....note the black insulator on a good one is maybe 2 inches long (showing) many have been shortened because they were damaged or cracked and there are no replacements available. I have thought about having some made but suspect the price to machine a few would be excessive. Sorry, don't know why the pictures are on their side. The last sketch is what I believe a good original would be dimension wise. Edited March 10, 2019 by Barney Eaton (see edit history) Link to comment Share on other sites More sharing options...
tinmann83 Posted August 21, 2020 Share Posted August 21, 2020 Is there a good source for the plastic core material? Repairing a 65 wildcat antenna Link to comment Share on other sites More sharing options...
Barney Eaton Posted February 13, 2021 Author Share Posted February 13, 2021 The plastic coated wire can be purchased at most home improvement stores... it is listed as 1/8 dia (that is the size over the plastic coating) If you buy some, measure it first with calipers.... shoot for as close to .120 as you can get. i have purchased it off Ebay and the tolerance varies often up to .130 which might bind in some places. You need about 36 inches for the Delco Slimline (1980- to end of production) If you are doing a '60's or '70's Tenna antenna you need closer to 60 inches. I have found a local machinist that will make the black plastic insulator that goes at the top of the fender. He has made some for the '63-'65 Riviera and can do them for other years but we would need to know the length. He charges $20 which seemed high at first but if he charges $100 per hour for his work, that would be 12 minutes of his time and there is no way he can machine one in that short period, so I think he is giving me a bargain. Good used chrome mast are still very hard to find and that may be the single item that prevent some from being repaired/rebuilt. If you have any power antenna question I can be reached at Barney@texas.net Link to comment Share on other sites More sharing options...
psychostang Posted February 13, 2021 Share Posted February 13, 2021 Hi Barney. That's my problem. My power antenna motor works, but I need a mast. Link to comment Share on other sites More sharing options...
telriv Posted February 14, 2021 Share Posted February 14, 2021 Andrew, Barney, not trying to take the bread & butter out of your mouth, BUT Andrew does have other options. IF you are repairing the original power antenna as you know they don't go down all the way so you would need to put a hole in your car cover IF you use one. You do have options as far as a power antenna goes that will retract all the way so a hole doesn't need to be put into your cover & it still looks as stock. Just do a search & you should be able to find it on this forum. Tom T. Link to comment Share on other sites More sharing options...
Barney Eaton Posted February 18, 2021 Author Share Posted February 18, 2021 There are aftermarket antenna offered on Ebay and auto parts stores that retract to the fender line. All of these antenna are made in China and come with a set of plastic adaptors for the fender hole. Also you would need to do some wiring changes when using on any radio that did not have a output wire sending 12v to the antenna that raises it when the radio is turned on. None of the above are big problems but none are plug n play.... you would need to adapt them to fit your fender trim and wiring. I have made a rough prototype for the 63 -65 Riviera using a late Delco Slimline antenna. Made an adaptor at the top and black insulator.... and the wiring is not an issue but time and lack of interest shelved the idea. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now