65VerdeGS Posted May 19, 2023 Share Posted May 19, 2023 I have a '65 Riviera. The Shop Manual states that the Propeller shaft slip spline is to be lubricated every 12,000 miles, with "Lithium EP Grease". This slip spline is accessed via a hole in the frame in the area where the "X" members of the frame intersect. Fig 1-2 on page 1.3 "Maintenance" of the Shop Manual says "Remove plug, lubricate and replace plug". On my car there is no 'plug', which has gone missing. When I took the car in for service recently the mechanic said he couldn't lube the slip spline because he didn't have the necessary fitting for his grease gun. So, what sort of fitting is needed to lubricate the slip spline? Is this fitting something rare, or easily obtained? I guess I'll have to buy the fitting and lend it to the shop, or crawl under the car myself and apply the lube. What happens if the slip spline runs dry of lube? What symptoms would develop? Do you get a noise setting up? What does this noise sound like? Link to comment Share on other sites More sharing options...
EmTee Posted May 19, 2023 Share Posted May 19, 2023 It is probably a slim extension/adapter to allow reaching into the joint. The adapter has to be held firmly against the fitting since it can't grab the zerk fitting. Link to comment Share on other sites More sharing options...
JZRIV Posted May 19, 2023 Share Posted May 19, 2023 (edited) Hard to believe a shop wouldn't have this needle adapter. I've had one since I was 16....but then again I had a Riv when I was 16. I've used it for other applications over the years. Edited May 19, 2023 by JZRIV (see edit history) 2 Link to comment Share on other sites More sharing options...
Riviera63 Posted May 19, 2023 Share Posted May 19, 2023 3 hours ago, 65VerdeGS said: I have a '65 Riviera. The Shop Manual states that the Propeller shaft slip spline is to be lubricated every 12,000 miles, with "Lithium EP Grease". This slip spline is accessed via a hole in the frame in the area where the "X" members of the frame intersect. Fig 1-2 on page 1.3 "Maintenance" of the Shop Manual says "Remove plug, lubricate and replace plug". On my car there is no 'plug', which has gone missing. When I took the car in for service recently the mechanic said he couldn't lube the slip spline because he didn't have the necessary fitting for his grease gun. So, what sort of fitting is needed to lubricate the slip spline? Is this fitting something rare, or easily obtained? I guess I'll have to buy the fitting and lend it to the shop, or crawl under the car myself and apply the lube. What happens if the slip spline runs dry of lube? What symptoms would develop? Do you get a noise setting up? What does this noise sound like? My shop did the one on my 1963. They used the needle adaptor as JZRIV pointed out. Bill Link to comment Share on other sites More sharing options...
gungeey Posted May 19, 2023 Share Posted May 19, 2023 (edited) You definately want to get the plug. Road dust is building up in there. It's not conventional hardware 1/4•24 with a 9/32 hex head Edited May 19, 2023 by gungeey (see edit history) 1 1 Link to comment Share on other sites More sharing options...
NTX5467 Posted May 19, 2023 Share Posted May 19, 2023 Rather than the original spec grease, might consider the newer syn chassis grease that includes moly (to meet the wheel bearing lube specs for "Ford disc brakes"). Valvoline makes one, used to be in a darker blue cartridge, but is now gray. This way, better lube which should last longer. Good lube shops used to have a different "needle end" for their grease guns, seldom used, back then. Considering that modern vehicles have FEW grease zerks on them, not surprising that the shop had no "needle". For modern times, might there be some plastic or rubber plug which could be reliably put in that hole, not needing a wrench to make happen? NTX5467 1 Link to comment Share on other sites More sharing options...
telriv Posted May 19, 2023 Share Posted May 19, 2023 The needle is for the CV Joint lubrication. The plug is a regular grease fitting size you can find on MANY of the greaseable front end components on our Riv's. The grease fitting adds out of balance weight & you will usually end up with a driveline/driveshaft vibration. Tom T. 1 Link to comment Share on other sites More sharing options...
gungeey Posted May 19, 2023 Share Posted May 19, 2023 Be wary of driving with other than the factory plug. Too deep and you risk spline damage. Link to comment Share on other sites More sharing options...
JZRIV Posted May 20, 2023 Share Posted May 20, 2023 18 hours ago, telriv said: The needle is for the CV Joint lubrication. The plug is a regular grease fitting size you can find on MANY of the greaseable front end components on our Riv's. The grease fitting adds out of balance weight & you will usually end up with a driveline/driveshaft vibration. Tom T. Yea I missed that and thanks for correction Tom. Shop manual says remove plug and lube. With the slip joint being inside the frame tunnel removal and reinstall of plug is not a fun task. Much easier when the shaft is out. Link to comment Share on other sites More sharing options...
60FlatTop Posted May 20, 2023 Share Posted May 20, 2023 Within a week of buying my '64 Riviera I was at the Buick dealership to have the CV joint greased with their needle. They gave me a service ticket for $1.50. When I paid the cashier said "Wow! No one gets out of here that cheap." While I was hanging out with Fred and Lynn, the two mechanics., this was 1978, I noticed the music in the shop was coming from a 1965 showroom radio display with a '65 AM/FM radio playing. The only difference between it and a ;64 was the knobs. I asked the guys what it would take to get that radio from them. "Just another radio" was the reply. After paying the bill I ran up to Grants and bought a nice new AM/FM for about $20. And everyone was happy. The radio is still in the car today. On the point about using the factory part, definitely. I can tell some real horror stories about hardware store bolts, etc. being used on cars. Link to comment Share on other sites More sharing options...
65VerdeGS Posted May 23, 2023 Author Share Posted May 23, 2023 On 5/19/2023 at 4:50 AM, gungeey said: You definately want to get the plug. Road dust is building up in there. It's not conventional hardware 1/4•24 with a 9/32 hex head Thanks all for the info on the fitting and plug. Now where do I get the correct plug? Any ideas? Looks like I need to buy the needle adapter needed to reach the joint? Can I get both the plug and the needle adapter from a jobber like NAPA? Thanks again. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now