johnworden1

You betcha! Your parts saved the truck project. John

Ok Dave. The tank can be junk other than the neck. Thanks. Be safe on the road. John

OK thanks. John

Would anyone have an otherwise junk fuel tank they would cut the fill neck off of so I could solder it onto the pictured tank? I would like several inches of metal beyond the solder joint remaining for trimming and fitting purposes. Also what is the thread at the pickup tube? Thanks. John

I have a 1911 Baker Model O Light Truck chassis for sale. It could be powered with a new electric system and a wood cab and flatbed built to resemble the original. The wood wheels can be duplicated with hard rubber tires. It would be very unique to say the least. I could build the truck if desired or portions of it. I have cars to finish before I could take it on. I'm asking $3000,00 for it as is. Thanks, John Please excuse if I already contacted you.

Talk to Vintage Power Wagons in Fairfield Iowa .

When blasting large pieces I blast and immediately epoxy prime only portions of the whole that I can accomplish in 1 work day. Allow dry time . Protect that area and continue the 1 day blast/prime routine again until the project is finished. I work in a humid climate as well. Luck. John

Hey Oily, If the fellows you mentioned are interested I have a 1911 Baker Model O Light Truck rolling chassis for sale. Message me here if so. Thanks. John

Factory manuals purchased off the shelf of a closed machine shop. No cleaning done other than vacuuming. Appear to be complete and other than some stains are in nice condition. $200.00 each plus ship. Thanks. John

OK thanks john

Vic, I would like for you to send the wiper cover and the color information for it. Do you have color information for the red you used on your 37? I could use that info as well. I will return the cover and reimburse you for the shipping cost. John Worden 405 Green Mountain Road Green Mountain, Iowa 50632 641 474 2313 home/shop Thank you. John

Restore the chassis with new wood wheels and solid rubber tires. Build a simple flat bed and phone booth cab. Fit new motor , controller etc and have truly one of a kind and probably the the only one left that actually runs. Data plate still attached to frame. I saved it from the scrapper. $5000.00 owns it. Located In Iowa. Thanks, John

Gardner Westcott in Michigan and Restoration Supply in Escondido Ca. are good sources.

PDN ?

Bill delivered a Dearborn Deuce body to my shop in Iowa last week. Excellent service. I found that, according to the biggies, I wasn't in the "lane"

SOLD

I need both left and right steel retaining moldings that run up the A piller at the door opening edge from floor past the dash to top of A piller. Dog leg shape. What have you? Thanks. John

Vic, More questions........ Do you have any parts with good original factory color? Do you think 38 Plymouth truck interior would be the same? Thanks for the offer. I may take you up on that. Can you provide the paint info and manufacturer name on the paint can label? I want to research the matter further. John

The interior parts are too rough to match. Those color analyzers pick the closest existing formula. Results vary. I prefer to locate a close color and tint myself. Thanks you anyway. John

Is the cover factory paint or one you painted? If factory paint I sure would like to borrow it. John

Vic, Do you have interior grey color information that I could use? John

Does anyone have a color code for the 37 cab interior? Thanks, John

Ok Thanks for the pics. I have new wood blocks made and fitted. I believe 3 stiff springs were used at 3 cab mount points but there are 6 cab to frame bolt holes. What goes where? I've seen cab to frame bolt/spring kits showing 3 long shoulder bolts, 3 springs and 1 short bolt with flat washers for all. Thanks John

bttt

For sale is a trailer made by cutting the frame rails (1974 Ford Camper Special ) under the cab and converting the result into a trailer. Floor is rusty with perforation. Located in Green Mountain Iowa 50632 $200.00 Thanks. John