TimFX Posted November 9, 2022 Share Posted November 9, 2022 Here is the cracked exhaust manifold off of a 1935 Oldsmobile. It’s also slightly bent I’ve heard it can be ground out, heated up and brazed Thoughts? Link to comment Share on other sites More sharing options...
leomara Posted November 9, 2022 Share Posted November 9, 2022 Cast iron has to be heated prior to repair. I'm not proficient so contact PennDutch Restoration Services and ask. They are currently rebuilding a 1928 Chrysler engine for me that had a small hole in the water jacket. They sent it out to a local place which specializes in repairing cast iron. Link to comment Share on other sites More sharing options...
DFeeney Posted November 9, 2022 Share Posted November 9, 2022 When finished be sure it has been surfaced ground. Have you posted on the Oldsmobile forum page looking for a good manifold? 1 Link to comment Share on other sites More sharing options...
Bloo Posted November 9, 2022 Share Posted November 9, 2022 (edited) Don't use brass that close to the engine. It melts. Maybe it could be welded with nickel rod after being heated in a furnace, but your best option is replacement if there is any way. Exhaust manifolds are a special case, as the metallurgy changes a little from the heat, and they take a lot of abuse from expansion, contraction, and twisting from the exhaust system. In my experience repairs usually do not last. I would show it to one of the cold cast iron repair guys first and see if that is a possibility. Next is welding. I believe @Dave39MD had an exhaust manifold welded by a forum member. Last I heard, it was still holding fine. Maybe he knows where to get that done. But just get a good one if there is any way to do so. Edited November 9, 2022 by Bloo (see edit history) Link to comment Share on other sites More sharing options...
32PONTIAC Posted November 9, 2022 Share Posted November 9, 2022 Call Steve Babinsky in Lebanon NJ 908-236-6400 he did a great job on a 32 Pontiac manifold for me really knows what to do and how to do it. 2 Link to comment Share on other sites More sharing options...
Dave39MD Posted November 10, 2022 Share Posted November 10, 2022 (edited) PaulS on this site welded mine and it is still holding through many heat cycles. Here is the post; Exhaust manifold repair October 1, 2020 in Technical Edited November 10, 2022 by Dave39MD (see edit history) 3 Link to comment Share on other sites More sharing options...
ILIKECARS53 Posted November 10, 2022 Share Posted November 10, 2022 12 hours ago, 32PONTIAC said: Call Steve Babinsky in Lebanon NJ 908-236-6400 he did a great job on a 32 Pontiac manifold for me really knows what to do and how to do it. I agree. It does not get any better for that type of work. Link to comment Share on other sites More sharing options...
TimFX Posted July 20, 2023 Author Share Posted July 20, 2023 Update! it has been welded and installed. So good so far 3 Link to comment Share on other sites More sharing options...
TTR Posted July 20, 2023 Share Posted July 20, 2023 13 hours ago, TimFX said: Update! it has been welded and installed. So good so far How many heat cycles and/or miles since the repair ? Link to comment Share on other sites More sharing options...
TimFX Posted July 20, 2023 Author Share Posted July 20, 2023 6 hours ago, TTR said: How many heat cycles and/or miles since the repair ? Driven about 100 miles in 20-ish intervals. More planed on the weekends 2 Link to comment Share on other sites More sharing options...
TTR Posted July 22, 2023 Share Posted July 22, 2023 On 7/20/2023 at 1:14 PM, TimFX said: Driven about 100 miles in 20-ish intervals. More planed on the weekends Good to hear. Please, report back after, let's say 500 or 1000+ miles and tell us how the repair is holding up. Care to share how it was done, how it looked right after it was repaired (pictures ?) and perhaps who did it ? 1 Link to comment Share on other sites More sharing options...
RUF Posted August 15, 2023 Share Posted August 15, 2023 Calling all collectors - Looking for an exhaust manifold for a Buick - 1931 - Model 60. Can be contacted at rufuscanti27@gmail.com. 1 Link to comment Share on other sites More sharing options...
Tonz Posted November 13, 2023 Share Posted November 13, 2023 I do a bit of welding for my self and am definately not a professional. But I've somehow had great success with cast iron. Many years ago I read and interesting 1940s article on welding broken cast spoke wheels on prewar agricultural machinery. These guys had to fix their own stuff. The gist was heating the part are the right spots to expand the iron before the welding and a long slow cooling. Years later when it was playing with my home made steam engine we broke the flywheel when pushing in the centre boss. So I decided to use my stick welder with normal rods to fix it. so I took the plates off my gas BBQ and heated it on max to about 300°C for 30 minutes, then did the welds. While still hot I gently peened the welds with a light hammer to stop crystallisation, covered and wrapped, or bury in deep sand overnight. As the photos show it's still good today. this could also work on an iron manifold. I would find a junk item to experiment on. 4 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now