David_Leech Posted July 8, 2022 Share Posted July 8, 2022 1928 Standard Six Still on a six volt system. I think the starter cable is undersized or at least in poor condition and in need of replacing. Same with the chassis ground. It cranks too slow, barely sometimes. What size cables should be used on a six volt system? Link to comment Share on other sites More sharing options...
Bloo Posted July 8, 2022 Share Posted July 8, 2022 #00 would be a good choice. Some cars got by on less (maybe #1) but probably never as small as the #4 typically sold for 12v systems today. <Smaller> - 8 - 4 - 2 - 1 - 0 - 00 - 000 - 0000 - <Larger> Think of it as a big circle from the battery post to the starter post, through the windings, and then from the starter case all the way back to the other post of the battery. For instance, if the ground cable goes to the frame instead of the engine/transmission, then there needs to be a third battery cable (or strap) running from the frame to the engine/transmission. It needs to be as good as the positive and the negative cable. 1 Link to comment Share on other sites More sharing options...
David_Leech Posted July 9, 2022 Author Share Posted July 9, 2022 33 minutes ago, Bloo said: #00 would be a good choice. Some cars got by on less (maybe #1) but probably never as small as the #4 typically sold for 12v systems today. <Smaller> - 8 - 4 - 2 - 1 - 0 - 00 - 000 - 0000 - <Larger> Think of it as a big circle from the battery post to the starter post, through the windings, and then from the starter case all the way back to the other post of the battery. For instance, if the ground cable goes to the frame instead of the engine/transmission, then there needs to be a third battery cable (or strap) running from the frame to the engine/transmission. It needs to be as good as the positive and the negative cable. 00! There's my problem... It's running what looks like #4 and just has a braided chassis ground. I knew I was going to need to make some cables, just surprised how undersized they really are! 1 Link to comment Share on other sites More sharing options...
Bloo Posted July 9, 2022 Share Posted July 9, 2022 (edited) Braids are fine if they are big enough. The chassis ground only needs to be full size if the starter current is flowing through it. If you have #4, then larger cables and clean connections should make a big difference. Good luck! 🙂 Edited July 9, 2022 by Bloo (see edit history) Link to comment Share on other sites More sharing options...
Power Wagon Dude Posted July 10, 2022 Share Posted July 10, 2022 Good Information on Sizing of wire. When I rebuilt my D-B, I took the 'flexible' Armored wire cover to my local Electrical (Wholesale) store and asked them to put the largest copper wire they could 'fit' in that flexible conduit. They suggested that I use a THN or THHN 'Heat Resisting' wire insulation. I also had them install / 'Crimp" on copper lugs and shrink fit tubing (Red for Hot - Black for neutral) onto the lugs, so wire polarity was never in question. I have NEVER had a problem with melting or damaging any of these wires. Good Luck, from someone who Been there - Done that. Link to comment Share on other sites More sharing options...
David_Leech Posted July 11, 2022 Author Share Posted July 11, 2022 5 hours ago, Power Wagon Dude said: Good Information on Sizing of wire. When I rebuilt my D-B, I took the 'flexible' Armored wire cover to my local Electrical (Wholesale) store and asked them to put the largest copper wire they could 'fit' in that flexible conduit. They suggested that I use a THN or THHN 'Heat Resisting' wire insulation. I also had them install / 'Crimp" on copper lugs and shrink fit tubing (Red for Hot - Black for neutral) onto the lugs, so wire polarity was never in question. I have NEVER had a problem with melting or damaging any of these wires. Good Luck, from someone who Been there - Done that. I'm going to take the old cables to work this week and make new ones. I will solder on the new lugs. I think we have #4 to 0000 in stock. Link to comment Share on other sites More sharing options...
cutdown Posted July 13, 2022 Share Posted July 13, 2022 (edited) Battery cables cant be too big, and I suggest you run the cables from the battery to the starter motor as well as the earth straight to the engine. That way you avoid voltage drop between engine and battery because you eliminate 2 extra connections in the earth circuit. Use your old earth cables to go from the engine to the body/chassis. On older vehicles, I also recommend running earths from all lights etc, direct to the battery for the same reasons. As a mechanic, I have seen too many stupid problems created by bad earths. Edited July 13, 2022 by cutdown (see edit history) Link to comment Share on other sites More sharing options...
Pete K. Posted July 14, 2022 Share Posted July 14, 2022 All good info here. I use "00" on the old 6 volt vehicles. Not to go cuckoo here, but if you look into the Theory Of Electricity, electrons tend to travel on the outer strands of a conductor, under the insulator obviously. 00 gauge will work just fine. Soldering ends on works better than a crimp, but there is an art to solder correctly without burning or wicking. Link to comment Share on other sites More sharing options...
keithb7 Posted July 15, 2022 Share Posted July 15, 2022 On my old Mopars that have battery under the front seat I find “00” is a little too big. The cables leave the top battery posts then quickly turn down under the battery box to the chassis. Single “0” is adequate and fits better. 1 Link to comment Share on other sites More sharing options...
David_Leech Posted July 17, 2022 Author Share Posted July 17, 2022 Thanks for the advice. I just located my real hard start issue, the rear housing on the starter fractured. Not sure how. New topic to follow... Link to comment Share on other sites More sharing options...
Bill kelly Posted July 20, 2022 Share Posted July 20, 2022 00 cable I used a forklift battery for positive ground and 975 cranking amp’s. On your starter center plate and bushings are good Link to comment Share on other sites More sharing options...
Bill kelly Posted July 20, 2022 Share Posted July 20, 2022 8 minutes ago, Bill kelly said: 00 cable I used a forklift battery for positive ground and 975 cranking amp’s. On your starter center plate and bushings are good I would love to see what inside of fuel vacuum should look like Link to comment Share on other sites More sharing options...
Farmallregular Posted July 21, 2022 Share Posted July 21, 2022 On 7/14/2022 at 9:35 AM, Pete K. said: All good info here. I use "00" on the old 6 volt vehicles. Not to go cuckoo here, but if you look into the Theory Of Electricity, electrons tend to travel on the outer strands of a conductor, under the insulator obviously. NOT TRUE...the skin effect only applies to alternating current, not to DC. At DC, current distributes more or less uniformly through the conductor. Any place that works on over the road trucks will have, or can make/get, 2/0 cables. Keith Link to comment Share on other sites More sharing options...
Pete K. Posted July 22, 2022 Share Posted July 22, 2022 By Jove Farmallregular, you are correct. DC current DOES flow mostly uniformly through a conductor. Good eye farmall! Link to comment Share on other sites More sharing options...
David_Leech Posted July 22, 2022 Author Share Posted July 22, 2022 22 hours ago, Farmallregular said: NOT TRUE...the skin effect only applies to alternating current, not to DC. At DC, current distributes more or less uniformly through the conductor. Any place that works on over the road trucks will have, or can make/get, 2/0 cables. Keith I'm at a Mack Truck dealer, made my cables here with 2/0 and soldered on copper lugs. Ran dual starter relays bridged with a copper bus. Not taking any chances with this installation! Link to comment Share on other sites More sharing options...
Mattml430 Posted July 22, 2022 Share Posted July 22, 2022 2 hours ago, David_Leech said: I'm at a Mack Truck dealer, made my cables here with 2/0 and soldered on copper lugs. Ran dual starter relays bridged with a copper bus. Not taking any chances with this installation! I spent 12 months next to a marine electrician completely re wiring a 72 foot cruiser and on all the cables, especially high current cable he always told me to crimp them before soldering them. He told me if ever there was a loose terminal the solder can melt and then it would come loose. It made good sense after he explained that, so did your man crimp your terminals before soldering them, he most probably did. Link to comment Share on other sites More sharing options...
Farmallregular Posted July 22, 2022 Share Posted July 22, 2022 19 hours ago, Pete K. said: By Jove Farmallregular, you are correct. DC current DOES flow mostly uniformly through a conductor. Good eye farmall! Thanks. Spent 45 years as a practicing engineer on an assortment of spacecraft, aircraft and communications systems, skin effect is something you worry about at RF. Keith Link to comment Share on other sites More sharing options...
trimacar Posted July 22, 2022 Share Posted July 22, 2022 If you really want best ground, run a ground cable directly from battery to starter mounting bolt, cleaning surface of paint and primer. Makes a huge difference. I have one car with ground going both to starter and to frame, no issues and engine turns over quite well. They started well when new, with nice clean frame connections. 100 years of rust and corrosion, not so much… Link to comment Share on other sites More sharing options...
David_Leech Posted July 23, 2022 Author Share Posted July 23, 2022 7 hours ago, Mattml430 said: I spent 12 months next to a marine electrician completely re wiring a 72 foot cruiser and on all the cables, especially high current cable he always told me to crimp them before soldering them. He told me if ever there was a loose terminal the solder can melt and then it would come loose. It made good sense after he explained that, so did your man crimp your terminals before soldering them, he most probably did. When I solder them I fill the lug with solder and once it's melted, plunge the cable in. Couldn't crimp it if I wanted to. Link to comment Share on other sites More sharing options...
David_Leech Posted July 23, 2022 Author Share Posted July 23, 2022 4 hours ago, trimacar said: If you really want best ground, run a ground cable directly from battery to starter mounting bolt, cleaning surface of paint and primer. Makes a huge difference. I have one car with ground going both to starter and to frame, no issues and engine turns over quite well. They started well when new, with nice clean frame connections. 100 years of rust and corrosion, not so much… I'm going to run a ground to the new starter end plate. That's where mine is getting it's ground. For now, running it from the end plate to the frame or another good location. If I'm not happy, then I'll run one to the battery Link to comment Share on other sites More sharing options...
Bill kelly Posted August 4, 2022 Share Posted August 4, 2022 I need a 1927 dodge coupe door striker plate my number is 937-469-4429 Link to comment Share on other sites More sharing options...
David_Leech Posted August 11, 2022 Author Share Posted August 11, 2022 The starter is rebuilt and cranks over fantastic now. No ground to the starter, just the frane Link to comment Share on other sites More sharing options...
Mark Gregush Posted August 11, 2022 Share Posted August 11, 2022 On 8/4/2022 at 12:32 PM, Bill kelly said: I need a 1927 dodge coupe door striker plate my number is 937-469-4429 Best to start your own wanted ad, not at the end of someones post about battery cables. Don't post your number in a public forum, anyone can read it logged in or not. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now