Fred Rawling

I thought that that was the original pattern but they looked so good that I figured you had replaced them. Thanks for the reply.

Doors @25.00, rear window $35.00, bare fenders and hood @ 25.00, pointed cone and curved bar from the front bumper $45.00 each, nice not rusted dash-front piece and top opiece @ $5.00. The original black paint is still good.; rear coil springs $5.00; drag link $20.00, exhaust cross over $25.00, wheels @10.00, steering column and gear box $65.00; 6 portholes - rims look nice, some pits on the inside- I will send a picture- @$10.00. most of the stainless steel trim for the body and doors, plus a pile of other parts. fredrawling@verizon.net

1965 Electra Parts: Left and right front fenders $50.00 each; front bumper $25.00; rear bumper $45.00; Front doors from a 2 door @/$25.00 or will sell parts off the doors; gage cluster $35.00. I have a few other knobs and switches off the dash, and a glove box lock without the key for $1.00 each.

Nice bumper with a couple of small dings. Pictures on request. fredrawling@verizon.net $100.00 plus shipping.

I have 2 14 inch wheels from a 1964 full size. They look like they are in good condition. One has a G 78 14 tire on it that looks real good. With or without the tires: $10.00 each plus shipping. fredrawling@verizon.net

Where did you find the material for the seats?

I have a hood from a 55 Special 4 door in California. Shipping will be expensive. It is straight. I would like $50.00 plus shipping. Let me know if you are interested.

I would say that your ring and pinion is out of adjustment and wearing out the gears. You better pull the cover and check the adjustment and see how bad the damage is or you will end up getting towed home. One possible cause is that the seal at the front of the torque tube could be leaking trans oil into the rear end. Do you have to add trans oil and do not see a leak? If you have to replace the rear end gears, which I did, you could use a standard trans gear set. I used a standard trans rear end gear set on my 1950 Roadmaster with dynaflow and it runs fine. I just lost a little mileage because the standard ratio was lower than the dynaflow ratio. This is an everyday driver and I had to get it going again so after a week of looking for the correct gear set, I took what was available.

I can come up with about 6 bolts @$7.50 each. They have good threads. I also have the wedges at $1.50 each if you need them. fredrawling@verizon.net

For my Station Wagon, I need 61 or 62 tail light lenses and a grill for a 61 Special. It is different from the Skylark grill. fredrawling@verizon.net

bobsautoamobilia.com for the water manifold and the local hardware store for cork to cut your own pan gasket. If you put any kind of adheasive on the cork when you install it, make sure that you only put it on one side of the gasket. Use something like permatex on the other side so you can get the pan off if you ever have to do that again.

Pat is closer to you than I am but if his heater motor does not work, contact me. fredrawling@verizon.net

can anyone tell me if the hood and trunk letters for 61 Special are the same as 62 Special? Also, does anyone have a line on a 61 Special Grill?

send me a picture or scan the lens and e-mail me the scan to fredrawling@verizon.net I have a box full of lenses. Fred

I am sorry that I posted the wrong date. It was Oct 10.

If anyone can be satisfied with used fenders for a 1940 series 80-90, I have a left and right fender. They are supposed to be series 80 and 90 but it would be wise to check measurements. I can e-mail photos. fredrawling@verizon.net I have a hood also and a gas cap door.

I have some off a 1955 special in California by Long Beach

THE LOCATION IS THE 55 FREEWAY AND 17TH STREET IN TUSTIN AT ENDERLY CENTER, A SHOPING CENTER. GO EAST FROM THE 55 FREEWAY 1 BLOCK. YOU WILL SEE DIRECTION SIGNS. THERE WILL BE VENDORS IN THE SWAP AREA. E-MAIL ME FOR MORE INFORMATION OR A MAY. fredrawling@verizon.net or call (562) 925-9545 days, (562) 867-7803 evenings

I just wanted to post this again.

Anyone who wants a map or information about the Ornage County Chapter show this weekend, e-mail me. fredrawling@verizon.net There will be a swap meet and there is vendor space open for $12.00 per spot. You can also call me at (562)925-9545 during the day or (562) 867-7803 in the evening. If you miss me and leave a message, do not race through your phone number.

Bill, I have too many e-mail addresses and web sight pass words. My e-mail is fredrawling@verizon.net. I will dig the core out tomorrow and pack it up. Fred

3 Liberty lenses for sale: 1. LIBERTY LENS in 3/16 high letters. Balance of lettering says: MACBETH - EVANS GLASS COMPANY. Around lower edge: PAT. DEC. 8. 14. TYPE - D NO 4764 -S- 8 1/2. This is a new lens but there is a chip in the top edge about 1 inch long and in from the edge 3/16 inch and another chip next to it about 3/8 inch long and 3/16 deep from the edge. $10.00 plus shipping. 2. Same lettering as above, no chips, 2 light scratches about 1 inch long on the outside, one just left of center at 9:00 O'clock and the other by the edge at 9:00 O'clock. $20.00 plus postage. 3. LIBERTY LENS in 1/4 inch letters, balance of lettering: MACBETH - EVANS GLASS COMPANY. Around the bottom edge: PAT. DEC. 8. 14. TYPE - D. NO. 4764 - S - 2.8 2 (The last 2 is smaller than the other numbers). This one is 8 1/2 inches even though the size is not on the lens. The lettering around the bottom edge is larger than that on lens # 1 & # 2 above. This one has a fine scratch on the inside about 1 1/2 inches long and at 10:00 O'CLOCK. $20.00 plus postage. I took these from the moldy paper myself. They are new but slightly mis- handled. I can e-mail photos if you like. frawling@verizon.net

Thanks for the replys. I

Truck parts stores may have better quality bolts. I would call a couple of them to see what they have.

I have one from a 1961 Invicta. Is it the same. It holds water and looks like it is clean inside. If it works, how about $8.00 plus shipping? frawling@verizon.net