Stickybit Posted April 24 Share Posted April 24 (edited) Hi all Got a "new" Riviera with a 425 engine - and I'm a bit concerned that the oil pressure sensor or gauge may be faulty. First of all - the sensor more or less looks like the one on the attached image - and it seems to measuring roughly 55 ohms at idle, and lowering the resistance to roughly 20 ohms when speeding up the engine. This tells me that oil pressure is present and probably just fine - and that the sensor is doing some kind of work. The question is - would this sensor be the correct model for this engine? - because the oil pressure gauge kinda just either do nothing, or it just bangs the needle to the max. Is there a trick to do a quick test oil of pressure? - while not having a oil pressure tester at hand? Best regards, Søren Edited April 24 by Stickybit (see edit history) Link to comment Share on other sites More sharing options...
NTX5467 Posted April 25 Share Posted April 25 (edited) I suspect the sender might be a "will fit, looks like it will fit" rather than what it really needs. You might go into www.rockauto.com and input your vehicle information for a new sensor (what GM calls it) and see if any of the markings on the unit match the part numbers of the brands RA has in their product listings. Not an exact situation, but about the only thing I can think of except using a manual gauge to verify your readings. No banging should be the ultimate result. In some cases, the part number is stamped on the hex where the threads are, or at least the max psi for the gauge calibration. Might need a mirror or use your phone to get a picture, carefully. Just some thoughts, NTX5467 Edited April 25 by NTX5467 (see edit history) Link to comment Share on other sites More sharing options...
60FlatTop Posted April 25 Share Posted April 25 When in doubt put a test gauge on it. Link to comment Share on other sites More sharing options...
telriv Posted April 25 Share Posted April 25 I don't trust ANY of the electrical gauges. too many variables'. Mechanical ONLY in my opinion. Tom T. Link to comment Share on other sites More sharing options...
Stickybit Posted April 25 Author Share Posted April 25 Regarding the currently fitted pressure sensor - is the measurements 60 - 20 ohm (roughly) what would be expected for ´66 425 engine sensor? - or is something else to be expected (since the gauge seems to have a life of it's own). Best regards, Søren Link to comment Share on other sites More sharing options...
1965rivgs Posted April 25 Share Posted April 25 41 minutes ago, gungeey said: See below for correct application. They are readily available. It calls for a special socket as shown. Do as 60FlatTop shows and while the unit is out check your pressure at hot idle. If you're engine runs quiet you have enough oil pressure. If you didn't have enough oil pressure it would let you know 👍 Look long and deep enough you can always find a problem. Steve, you pictured the switch for the idiot light; the `66 uses a sender for a gauge. Link to comment Share on other sites More sharing options...
gungeey Posted April 25 Share Posted April 25 I stand corrected and fixed it Link to comment Share on other sites More sharing options...
1965rivgs Posted April 25 Share Posted April 25 Here are pics of an original '66 sender. I believe the "60" on the sender signifies it is a 0 to 60 ohm sender and the stamped part number, 6460470, is the correct part number in the Buick parts book. For what it's worth, the few times I've worked on the factory sender/gauge I've found them relatively worthless. If you want to closely watch the numerical values you'll need to go to an aftermarket gauge Tom Mooney 1 Link to comment Share on other sites More sharing options...
telriv Posted April 25 Share Posted April 25 An after market mechanical gauge. Tom T. 1 Link to comment Share on other sites More sharing options...
Turbinator Posted April 26 Share Posted April 26 I use mechanical Bosch water temp gauge and mechanical oil pressure gauges. Fitted where the ash tray was once located. When Idiot lights turn on I view the signal as “ too late.” Actually, I regard mechanical gauges more accurate and easier to install. In summation : to each his own. Later Gator Link to comment Share on other sites More sharing options...
NTX5467 Posted April 26 Share Posted April 26 My observation has been that the number stamped on the sensor is to match the gauge upper limit rather than the ohms max. Seemed to correlate to me as being "pressure". FEW people understand "ohms", but they know about "pressure". BTAIM I've found factory gauges (of any brand) to be two things. Accurate enough and "for reference". BUT you have to check them to see what they are doing! Happy Spring! NTX5467 Link to comment Share on other sites More sharing options...
1965rivgs Posted April 26 Share Posted April 26 (edited) 9 hours ago, NTX5467 said: My observation has been that the number stamped on the sensor is to match the gauge upper limit rather than the ohms max. Yes, POUNDS, not ohms. Communicating to the OP that the original sender as per part number is for a 60lb. gauge. There are several choices on the Napa website with good specification info. WARNING- I did not check specs to determine which sender, if any, correlates with a 60 lb. gauge https://www.napaonline.com/en/search?text=oil pressure sender&referer=v2 Tom Mooney Edited April 26 by 1965rivgs (see edit history) 1 Link to comment Share on other sites More sharing options...
RivNut Posted April 26 Share Posted April 26 I have what appears to be an OE '66 oil pressure sender. If you're interested, send me a PM Ed Link to comment Share on other sites More sharing options...
Stickybit Posted May 13 Author Share Posted May 13 Sorry the for late reply. 😮 I did a quick and dirty, and just ran the engine at idle speed with one valve cover removed from the engine - and saw the oil flow just fine. Yesterday I revisited the non-problem, and tested the pressure with a test gauge, and it produced 40 psi of pressure. All in all .. no problem with the oil flow as expected. 🙂 Best regards, Søren 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now