Petevelasco Posted January 11 Share Posted January 11 Good morning fórum I’m looking at replacing motor on 1936 Buick century any suggestions Link to comment Share on other sites More sharing options...
bryankazmer Posted January 11 Share Posted January 11 Century is best performing model with large engine in smaller body. Stick with factory fitment if you want to rod a 36 Buick, do a Special 1 Link to comment Share on other sites More sharing options...
Petevelasco Posted January 11 Author Share Posted January 11 Thank you, I was told that babbading the crankshaft was going to very $$$$$ Link to comment Share on other sites More sharing options...
bryankazmer Posted January 11 Share Posted January 11 There are still places that can rebabbet and line bore but make sure their machine is long enough to do a straight 8 Link to comment Share on other sites More sharing options...
Bloo Posted January 12 Share Posted January 12 (edited) I believe that the babbitted 320s were not built with precision shells on the main bearings, but were precision line bored, so that later 320 main shells (1940s) fit, and fit with no shims. I read that in a manual somewhere, and I am fairly sure it applies back to 1937. It is likely it goes back to 1936 too, because the 320 was a brand new engine design in 1936. I cant say for sure though. Some of the people in the "Buick Pre-War" section of the forum will know. It might pay to repost this in that section or move it. On the rods, those are babbitt for sure, and yes it is expensive. Later (late 40s?) 320 rods have shells instead, and you can probably substitute them. Someone I know has done it to a 37 320, and it is likely this trick would also work on a 36 but I don't know for sure. If you need pistons, 38 slightly domed pistons (which are more readily available) will fit a 37, but if I remember correctly maybe not 1936. I seem to recall there was something odd about the 36 combustion chamber. You would have to check piston clearance to the head very closely if you try it. Some grinding might be necessary if it will work at all. Replace the whole engine? I wouldn't unless I had to, but the 320 was made all the way through the end of the 52 model year. I imagine the newer you go with the engine, the more the problems pile up with engine mounts, accessory mounts, bolt holes, sender holes, carburetor angle, and so on. That is usually the case with GM engines. I also think that a 320 taken from a car with a Dynaflow might(?) need to be rebuilt with a different crankshaft. Better answers than mine will be available over in the "Buick Pre-War" section. Good luck, and welcome to the forum! Edited January 12 by Bloo (see edit history) 2 Link to comment Share on other sites More sharing options...
Petevelasco Posted January 12 Author Share Posted January 12 Thanks Bloo that was educational I also read somewhere that a52 Buick motor is straight fit if I were looking to swap motors 1 Link to comment Share on other sites More sharing options...
Gearheadengineer Posted January 13 Share Posted January 13 I just saw this: https://www.facebook.com/marketplace/item/1066717767679175 Link to comment Share on other sites More sharing options...
Petevelasco Posted January 14 Author Share Posted January 14 Thanks Gearhead engineer I need to looking into this Link to comment Share on other sites More sharing options...
pont35cpe Posted January 14 Share Posted January 14 5 hours ago, Gearheadengineer said: I just saw this: https://www.facebook.com/marketplace/item/1066717767679175 That looks like a 233 cu in for a 40series 1 Link to comment Share on other sites More sharing options...
Bloo Posted January 15 Share Posted January 15 And on the off chance anyone reading this is not already aware, a 40 series engine might look about the same in pictures but in person it is not. Expect a 40 series engine to be several *inches* shorter than a 320. Not interchangeable. Link to comment Share on other sites More sharing options...
MCHinson Posted January 15 Share Posted January 15 If you want to replace a 1936 320 engine, the best source for a used engine that will work would probably be Dave Tacheny. He sells 1936-1941 Buick parts. You can best reach him by calling 763-427-3460 between 4 and 7 pm Central. He may very well have exactly what you need. Link to comment Share on other sites More sharing options...
Dave Mellor NJ Posted January 15 Share Posted January 15 I know where there's a 36 Buick Chassis complete with running gear and a body shell in the Woods in Williamstown, NJ. If you're around here I could show it to you Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now