Buick35 Posted April 13, 2023 Share Posted April 13, 2023 (edited) My engine states to adjust valves to .015 engine hot.I was wondering if this could be accomplished using a heat gun for the same results rather than the motor cooling down while adjusting. I heard one or two of my rear tappets were a little louder than the rest. Thanks. Edited April 13, 2023 by Buick35 Spelling (see edit history) Link to comment Share on other sites More sharing options...
Robert Engle Posted April 14, 2023 Share Posted April 14, 2023 I adjust valves with engine warmed up and running at a low idle. It takes some practice to use the wrench and screw driver to make a change while running. There was a tool made that incorporated a socket and and screw driver blade with a palm knob on the top to turn the screwdriver blade. I wish I had one today. Bob Engle 2 Link to comment Share on other sites More sharing options...
Oldtech Posted April 14, 2023 Share Posted April 14, 2023 On 4/13/2023 at 12:44 PM, Buick35 said: My engine states to adjust valves to .015 engine hot.I was wondering if this could be accomplished using a heat gun for the same results rather than the motor cooling down while adjusting. I heard one or two of my rear tappets were a little louder than the rest. Thanks. No you can't use a heat gun. The complete block needs to be hot. As Robert says, check while running with a STEEL feeler gage. even if you only locate the ticky ones, you can adjust them with it stopped until they are right. 3 Link to comment Share on other sites More sharing options...
Bloo Posted April 14, 2023 Share Posted April 14, 2023 Also you need to warm the engine up by driving it. Warming it up in the driveway will give different results. 1 Link to comment Share on other sites More sharing options...
drovak Posted April 15, 2023 Share Posted April 15, 2023 The last time I tried to use my old Craftsman feeler gauges while it was running, they turned bowl-shaped thanks to the hammering action. Link to comment Share on other sites More sharing options...
Marty Roth Posted April 17, 2023 Share Posted April 17, 2023 (edited) On 4/14/2023 at 5:56 PM, Oldtech said: No you can't use a heat gun. The complete block needs to be hot. As Robert says, check while running with a STEEL feeler gage. even if you only locate the ticky ones, you can adjust them with it stopped until they are right. Good advice, but also be sure to adjust the rest of the valves - not only the "ticking" ones, the ones not ticking just may be too tight, not allowing the valve to sit on the head long enough (or at all), possibly leading to burned valves Edited April 17, 2023 by Marty Roth typo (see edit history) 2 Link to comment Share on other sites More sharing options...
Marty Roth Posted April 17, 2023 Share Posted April 17, 2023 On 4/14/2023 at 7:52 PM, drovak said: The last time I tried to use my old Craftsman feeler gauges while it was running, they turned bowl-shaped thanks to the hammering action. I had that happen many years ago - 1950s? Learned to drive enough to get engine up to full operating and then drive several more miles- then pull the valve / rocker cover with engine off, and adjust valves. Always worked like a charm, from my 1932, and 1951 Chevys up to my 1958 Triumph TR-3 1 Link to comment Share on other sites More sharing options...
Oldtech Posted April 17, 2023 Share Posted April 17, 2023 Yep. That's why I said a Steel feeler gage, most aren't that good. More practical to just try to be quick. Link to comment Share on other sites More sharing options...
drovak Posted April 17, 2023 Share Posted April 17, 2023 If my Craftsman feeler gauges aren't steel, then I'm not sure what they are! Link to comment Share on other sites More sharing options...
Mark Shaw Posted April 22, 2023 Share Posted April 22, 2023 I have multiple sets of feeler gauges. Only one set is used for checking tappets while running because the thickness of the feelers will be changed slightly after being pounded by running tappets. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now