edselsouth1 Posted September 27, 2010 Share Posted September 27, 2010 I've got down to the radio module on my 1988 Reatta, and can only find two electrical connectors on the top of the module. There are, however, four spaces for connectors. One connector (white) is plugged in, and three spaces are open. I am assuming that there are other connectors to the module. What color connectors, and the order/color of the wiring in the remaining connectors. The PO had removed all of the aftermarket audio that was installed, and there are a number of wires that are taped, etc. I'll attempt to post a pic of the existing mess, and get a couple more and better pics tomorow. Thanks, David Link to comment Share on other sites More sharing options...
padgett Posted September 27, 2010 Share Posted September 27, 2010 There are two more connectors on the bottom. Link to comment Share on other sites More sharing options...
Guest Mc_Reatta Posted September 27, 2010 Share Posted September 27, 2010 I made up a list of these connectors and what wires are in each one a while back. It is posted on Ronnie's site, reattaowner.com. The two 4 pin connectors that are not plugged in are for the speakers. The other unused connector is for aux input, cell phone option etc. You can pick up the connectors at an auto stereo store, Walmart, ebay etc, and wire them back in if they aren't there anymore. Link to comment Share on other sites More sharing options...
edselsouth1 Posted September 27, 2010 Author Share Posted September 27, 2010 Padgett, Mc_Reatta, Thank you both. I did find the two connectors on the bottom, and they were plugged in. I'll look again on Ronnie's site for the connector wire post. I'll need to check for the blue connector, and see that all wires are in it. The speaker wires are probably the ones taped. I'll know tomorrow! David. Link to comment Share on other sites More sharing options...
Guest Mc_Reatta Posted September 27, 2010 Share Posted September 27, 2010 Here's the link to the table. Refer to the upper right - upper connectors.Radio & Cassette Connector Pinouts - ReattaOwner.comThe C2 White connector is not normally not there.Aftermarket units usually have all 4 connectors connected into one large plug. Link to comment Share on other sites More sharing options...
NCReatta Posted September 27, 2010 Share Posted September 27, 2010 The other unused connector is for aux input, cell phone option etc. Mc_Reatta,DO you know where I can get a aux cable for it? I'm guessing this would just enable me to plug an iPod, mp3, etc. into it? Link to comment Share on other sites More sharing options...
DAVES89 Posted September 27, 2010 Share Posted September 27, 2010 McReatta I think you should make them up and sell them. Of course I don't think many will want to pay a CRT for one! Link to comment Share on other sites More sharing options...
padgett Posted September 27, 2010 Share Posted September 27, 2010 Using the cell phone input might be the best way to get an AUX input. Hard part is switching from Radio to AUX. The cell phone circuit is 8A-152. Hopefully the ALDL is just used for dialing. Link to comment Share on other sites More sharing options...
Guest Mc_Reatta Posted September 27, 2010 Share Posted September 27, 2010 Problem is cell phone is a mono input.You need to find a car that had a cd player or cell phone installed to get that aux cable. Most folks just use the tape player input which goes to one of the bottom plugs on the radio module already as their aux input.In either case, you need a tape player that will at least respond to the CRTC that there is a tape in the player ready to be played which will enable the play option on the CRT before either of the aux inputs will work.You can make up an aux cable from the aftermarket combo plug (if you get the one with all 4 connectors not just the 3 for the radio) and an 3.5 mm mp3 connector cable if you are of the mind. That's how I made one for Dave a while back. Link to comment Share on other sites More sharing options...
NCReatta Posted September 27, 2010 Share Posted September 27, 2010 Where do I find said after-market combo plug? Just out of curiosity, what would you charge to make another one Mc_reatta? Link to comment Share on other sites More sharing options...
Rawja Posted September 27, 2010 Share Posted September 27, 2010 You can get the connectors you're looking for HERE. Link to comment Share on other sites More sharing options...
Guest Mc_Reatta Posted September 27, 2010 Share Posted September 27, 2010 Here us what you need, best place I found to get is off ebay.Gm Oem Reverse Radio Install Wiring Harness Male Plug - eBay (item 220675453486 end time Oct-27-10 14:00:38 PDT)Believe the section on the bottom plug on the right is the aux connector. The other 3 parts are for the standard radio connections. They don't supply wires and pins for the aux section, I cannibalized them from another connector. Link to comment Share on other sites More sharing options...
edselsouth1 Posted September 27, 2010 Author Share Posted September 27, 2010 Looked again at the wiring harness and connectors on the '88 today. It appears that all wires are hooked up properly except for the speaker wiring, both front and rear. The PO had just bundled them all together, and then got power from his radio unit. The connectors that the wires were to go in have been discarded. I believe I have to find the proper 4-pin connectors, wire the speakers in, and may be ready to go. Got to go to the salvage yard tomorrow. I'll update when I get the wiring repaired. Thanks to all for your information. David. Link to comment Share on other sites More sharing options...
D-a-n-i-e-l Posted September 28, 2010 Share Posted September 28, 2010 cell phone/cd/tape all work once the tape play button is pushed. All you need is a tape with no "tape" in it to activate the input. Link to comment Share on other sites More sharing options...
NCReatta Posted September 28, 2010 Share Posted September 28, 2010 Here us what you need, best place I found to get is off ebay.Gm Oem Reverse Radio Install Wiring Harness Male Plug - eBay (item 220675453486 end time Oct-27-10 14:00:38 PDT)Believe the section on the bottom plug on the right is the aux connector. The other 3 parts are for the standard radio connections. They don't supply wires and pins for the aux section, I cannibalized them from another connector.First of all David, I apologise for highjacking this thread... Mc, the eBay ad says it fits 90/91 reattas. I need it for an '89 I tried to follow the thread "MP3 Hook-up in an '89" but kept getting lost... perhaps someone could compose a cliffnotes version, for Ronnie's site? Link to comment Share on other sites More sharing options...
Guest Mc_Reatta Posted September 28, 2010 Share Posted September 28, 2010 (edited) NCReatta,It will fit pretty much all delco radios from 86 to 96. The same one fits all Reattas.What is it your trying to do?This one will work too, but doesn't include the aux connector portion. This is what is stock in cars without the phone or cd player option.http://cgi.ebay.com/GM-88-02-MALE-OEM-FACTORY-WIRE-HARNESS-GWH343-GWH-343_W0QQitemZ110427363736QQcategoryZ32809QQcmdZViewItemQQ_trksidZp4340.e17001.m7QQ_trkparmsZalgo%3DLVI%26itu%3DUCI%26otn%3D6%26ps%3D63%26clkid%3D5375134369187355004 Edited September 28, 2010 by Mc_Reatta (see edit history) Link to comment Share on other sites More sharing options...
NCReatta Posted September 28, 2010 Share Posted September 28, 2010 Oh, alright. I'm just trying to get an MP3 hookup in my '89. So, if I buy the connector, and solder in a 1/8" connector, it'll all work right? Are there four wires coming from the bottom right plug? Will I need to re-wire my radio with the new plug? or can I just butcher the one from eBay? Sorry I'm so ignorant, I'm just rather clueless (obviously). Link to comment Share on other sites More sharing options...
Guest Mc_Reatta Posted September 28, 2010 Share Posted September 28, 2010 Does your tape player work sufficently to allow you to get to hit play? Otherwise neither aux input will work. (has to respond to the CRT and sense that a tape is installed ready to play)Do you want to go through the tape player input (easier to get to) or leave the tape player alone and go through the aux input on the radio? (more work)The proper connector to mate with mp3 players is a 3.5 mm not the 1/8 inch one they sell at the rat shack. Link to comment Share on other sites More sharing options...
NCReatta Posted September 28, 2010 Share Posted September 28, 2010 Yes, it does, I can put a tape in, and press play, and it'll start to play it, but it'll cycle in and out... I would rather not have to take the seats out and finagle my hands in that tiny space to do it though the radio if possible. Is there a difference in sound quality between the two? I have a spare tape deck that I pulled from a '89 Riviera if that would help. I don't think it works, but my original plan was to make one good one out of two bad ones... but this would be a better use I think.Thanks for all the help. Link to comment Share on other sites More sharing options...
DAVES89 Posted September 28, 2010 Share Posted September 28, 2010 (edited) Here is what I did. I took the inner plug out of the Riv. tape deck. [What is wrong with your tape deck is probably what is wrong with the Riv tape deck]. On that plug there are 3 wires in a shield and one is outside the shield. Of the wires in the shield one is your right side speakers and one is the left. The third is the ground wire which gets wired into the loose wire on that same plug lead. All this then gets you about 8" of lead to go into the 3.5mm plug that you buy from Radio Shack along with a 3' or so lead with 3.5mm male and female ends on them. This allows you to run the lead under the console out the cigarette tray and give you lead to work with in your lap. The last part to this is that you take the tape deck bezel off, remove the tape deck. Leave the leads connected to the tape deck. Make the CRT play the tape deck, then turn off the tape deck, disconnect the lead that is the same as the one you just made. You then connect your new lead, put a cassette in [with the tape removed]. Engage the play button and you have music thru your MP3 player. You can then put the cassette deck back in it's spot and put the bezel back on and you are finished. I am sure that McReatta can help you with the wire colors or you can do it by trial and error. It is not hard to do and by doing it wrong you will not hurt anything, it just takes more time. Wiring thru the phone plug is overrated. I only did it because I spent the money to have the tape player fixed. I only use the radio or the MP3 lead. The cassette deck is way too slow. Or I will do it for $50.00 That will include both ends and shipping. PM me if interested. Edit notes. Please remember that I have to go to the yard to get a cassette deck, then Radio Shack for the MP3 lead. Solder everything up test it and send it. I really don't want to do it,but for $50.00 I will... BTW Ronnie was there one in that stuff I sent you? I thought I had a ready made one laying around but now I can't seem to find it... Edited September 29, 2010 by DAVES89 (see edit history) Link to comment Share on other sites More sharing options...
edselsouth1 Posted September 28, 2010 Author Share Posted September 28, 2010 Got the connectors from the salvage yard today for the '88. Wired them in, and got sound, but only through the left rear speaker (good quality and volume). The other speakers do power up, but can barely hear them. All of the radio functions seem to work properly (through the controller) other than the 3 speakers. Moving the connections in the module sometimes helps, and sometimes not. Getting a great amount of static when moving the connections at the module. The pins in the module may have corroded to the point of no return. Looks like I may need a module to replace this one? David. Link to comment Share on other sites More sharing options...
NCReatta Posted November 12, 2010 Share Posted November 12, 2010 Bumping back to the MP3 hook-up question (Sorry edselsouth1 for hijacking the thread. )I have a 3.5mm cord that I removed from a nice set of headphones that got stepped on at my church (teach you no to just push things off the desk! ). It has 4 wires. 1 left, 1 right, and 2 grounds. Getting ready to attempt to put this thing together tomorrow. Mc_reatta, do you know what color wires go to which channels? Is it nessicary to solder it together (don't have a soldering tool handy)? or can I just twist them together, and use electical tape?Thanks again, Link to comment Share on other sites More sharing options...
Guest Mc_Reatta Posted November 12, 2010 Share Posted November 12, 2010 Do you have a DVM to cross check the plug sectors to the individual wires? Typically the right channel hot wire is red, the left white or yellow, the grounds are black and brown. But they could have used any color they wanted to.In your case you will tie the two grounds together as there is only a common ground in the radio module inputs.They are very thin wires, really should solder. Doubt there is a crimp connector small enough for them. I have seen small wire nuts that might work. You can twist together, but without some type of mechanical means of holding them tight, it will eventually give you problems. Link to comment Share on other sites More sharing options...
DAVES89 Posted November 12, 2010 Share Posted November 12, 2010 What I do with thin wires without soldering is I peel back extra insulation, and fold the newly bare wire over and twist it. Then I put it in a solderless connection and crimp it. Do the same for the other end. Has worked for me. Link to comment Share on other sites More sharing options...
Guest Mc_Reatta Posted November 12, 2010 Share Posted November 12, 2010 Pin out for the 3.5mm plug is:Use your DVM to check which color wire goes to each section of the plug.Normally right channel is red and left channel is white. Other colored wire or shield wire will then be ground. Link to comment Share on other sites More sharing options...
NCReatta Posted November 12, 2010 Share Posted November 12, 2010 Ok, came really close to getting everything to work... BUT (I hate buts) Now my stereo has so much static, I can't hardly hear anything. it has static when the tape is playing and when the radio is on. I change the balance, and nothing changes with the static. volume doesn't either. It's good for the first 8 seconds when I first turn it on, but then it gets really bad. Did I completely kill something? I hate it when things don't go like they're supposed to.... Link to comment Share on other sites More sharing options...
padgett Posted November 12, 2010 Share Posted November 12, 2010 Have the capacitors been replaced ? Link to comment Share on other sites More sharing options...
NCReatta Posted November 12, 2010 Share Posted November 12, 2010 Nope.. Is that what I need to do? is that hard to do? Where can I get the capacitors?Thanks for all the help you guys. Link to comment Share on other sites More sharing options...
handmedownreatta Posted November 12, 2010 Share Posted November 12, 2010 grab a new module from an early nineties regal.i did. Link to comment Share on other sites More sharing options...
NCReatta Posted November 12, 2010 Share Posted November 12, 2010 grab a new module from an early nineties regal.i did.Like how early? Are there any other models that have the same part? Link to comment Share on other sites More sharing options...
handmedownreatta Posted November 13, 2010 Share Posted November 13, 2010 i think mine came from a 94 regal.you might search for daniels posts.hes posted a lot of radio info. Link to comment Share on other sites More sharing options...
NCReatta Posted November 14, 2010 Share Posted November 14, 2010 Mike @ BuickReattaParts.com suggested that I get a brand new module from M&R Electronics. it's $150. brand new. it should last me another 21 years. at least. that's probably the route I'll go. thanks for all yall's help. I appricate it. Link to comment Share on other sites More sharing options...
DAVES89 Posted November 14, 2010 Share Posted November 14, 2010 That is certainly a good opinion. I would also like to offer mine. I go to a pick and pull. I pay maybe $10.00 for one and 10 minutes to pull it. Reinstall is another 10 minutes. The radio I get should last 5 to 10 years. I don't think I will have either car that long. [both are very nice daily drivers but one has 180k the other 220k]. That $140.00 difference can be used buying other needed parts or building an inventory of back up parts to keep your car running. Link to comment Share on other sites More sharing options...
NCReatta Posted November 14, 2010 Share Posted November 14, 2010 This is what Mike said....first, about the radio. it gets really difficult to get that radio from cars other than Reattas, as you don't know which model radio the junk car has. the cooling fins have to be long like your radio module has, NOT the spikey ones that the non-equalizer radio has. also be sure the car does not have a Bose radio, as the Bose radio has no amplifier. Bose puts an amplifier at each speaker, not in the radio.. On top of that, I've been having trouble getting into u-pull-it yards since I'm so young. Most won't let me in until i'm 16, and then I have to have an adult accompany me. It makes it difficult. Link to comment Share on other sites More sharing options...
NCReatta Posted November 14, 2010 Share Posted November 14, 2010 Also, even if I were to go I'd be VERY lucky if I found a Riviera. much less a Reatta. Unlike where you live, there is a severe shortage of Reattas in U-pull-its in NC. Link to comment Share on other sites More sharing options...
handmedownreatta Posted November 14, 2010 Share Posted November 14, 2010 if you can afford the repaired one you can retain the graffic equizer.btw i buy a lot of parts off craigslist.theres people on there parting out all sorts of cars. Link to comment Share on other sites More sharing options...
padgett Posted November 14, 2010 Share Posted November 14, 2010 That is a good point: all Reatta radios have equalizers. Most Riviera radios do not. Only way to tell is the part number. I have an MNR radio in the blue car and it works fine. Were on "sale" for years, wonder if supply is getting low. Link to comment Share on other sites More sharing options...
Ronnie Posted November 14, 2010 Share Posted November 14, 2010 Nope.. Is that what I need to do? is that hard to do? Where can I get the capacitors?Thanks for all the help you guys.The link below will answer your questions about how difficult it is to replace capacitors. It is not too bad if you take your time and understand what you need to do before you start. IF you are going to junk your old radio unit it wouldn't hurt to try your hand at doing the repair. I got the capacitors at a local TV shop. They were not expensive at all but I can't remember the exact price.Radio Capacitor Replacement Instructions*-*ReattaOwner.com Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now