knobless

Here is a picture of mine that was on my 33 Plymouth 2 dr. PD....small arm connected to clutch pedal arm, and vacuum would depress clutch on its own, ( speed of the engine generated vacuum ).......it did work on my 33...

I may have one , make me an offer.. thanks

1936 Dodge Hood hinges ( clips) these are the small hinges that allow the hood to open. sold in sets only front and rear. Nickel Plated, $68, plus shipping. Contact Steve Raymond,NH 03077

too late for that, they are very brittle, looks to be a small score line at the ear bends, maybe a one time bend, oh well just another search ....for replacements...lol

Both Ian and I listed photos of windows 34 dodge DR model, its under "slow progress but getting there" good luck.

The spring can be installed on either side but will only work on the correct side. Back tabs on the assembly have to be loosened. The curved end of the spring should rest in the first slot(as showing) when in normal position and in the second slot when in the locked position.

Also saw this on line for sale $26, Also most the twin to mine,

Ian thanks for that photo, neat little car, I have included some pictures of spring replacing, door handles , the small ears that need to be bent up to install springs are very temperamental, broken one, but the guy I purchased springs from has new keeper, so I will just purchase them , and replace, step one /pry up ears to remove Keeper step two after removing, put spring in place as shown, step 3 align keeper in place , bend keepers back to original position. Step 4 they work,,,,,,,just need to do all of them......

sounds about the same as the guy I bought them from ( instructions for installation ) I may have time to try it tomorrow , any photos of the car for which you speak?? like to see it. thanks

Hi Ian I will check and get back with some photos, if I remember they both had the springs attached....Thanks Steve

Hi Ian Wondering if you put new springs in your door handles and if so how these springs are installed ? I see a vague reminisce of the old ones ( outline) but can not figure how they snap into place any idea would help, thanks Steve

http://www.ramreproductions.com/index.html

Dave Do you have those spring set ups separate? looking to do the springs over in my tail lights most are missing, thanks

As for the drain tube mine is missing ,but I would imagine it runs out the firewall and down as to drain below the car, not sure of location.

Hi Ian First off I did hear those few choice words over here....haha, The stainless has small "T" shape fasteners on the inside of the hood all you do is straighten them out ( twist with pliers ) to fit out through the slots in the hood, the slot and the "T' are the same shape, to install , line up the "T" with the openings on the hood and twist back to original position to hold them in place. I have my hood on a set of saw horses so it made for an easy task to remove all the hood hardware. good luck, and try to keep the fowl language to a minimum.....haha..

Hi Dave how much are the repro. hub caps. and do you have them for 34 also

Which ones are for sale???

second picture shows how the door lock comes apart in 2 pcs so you can take it out without removing the window channel.

looking for 1 of these window roller, have one also any info on what was used to go on the roller, rubber sleeve?

seems like the only piece I'm missing is the small part with the ears on it attached to the cross bar,,,, thanks for that pic.....

Here are a few more to check into:Soff-Seal: 800-426-0902 Metro Molded Parts: 800-878-2237 I will try and find some time this week to call or if you have a chance.......

Thanks again I will try them,

Pulled the window channel out before I found out that on this year the door lever is made in 2 pcs so once the handle pcs is detached the whole lock along with the small throw bar can be rove through the smaller bottom hole,,, who knew,, Also looking for the small roller set up as in photo , have 1 need the other side I thing they are universal fit , if any one knows of one and also need new roller material as in photo looks to be some type of hard plastic, ( baker lite )? small amount left on pass, side but drivers side is completely gone. Thanks

license plate bracket....

upon closer inspection of my seal on the passenger side frame it is all there and good enough to mold from I think"" but then again what do I know...HAHAHA...........