AlfaTazio Posted June 28, 2022 Share Posted June 28, 2022 Would someone know of a available puller, or, someone who might fabricate such a puller. I did have one made before for a different car, but can not locate him at this moment. Its going to be 2 3/8 inches by 16 tpi....internal threads on the puller itself. I know about the VCCA, but thought I would ask here first. Thanks, Link to comment Share on other sites More sharing options...
a sell Posted July 19, 2022 Share Posted July 19, 2022 I assume you have wood wheels. If you had disc wheels any 3 jaw puller can be bolted onto the lug nuts. With wood wheels many people just loosen the nuts and drive it around the block. Do not remove the nuts all the way for the obvious reasons. Another method is to jack up one side, and loosen the nut on the other side. Moving the car back and forth sideways is supposed to knock the other side loose. A fellow on the VCCA site used 2x4s behind the wheel with some all thread rods to put tension on the hub to remove it. Rather primitive but it worked. All of my early Chevys have disc wheels. 1-'25, 1-'28, 3-'29s, sorry I can't be more help. Gary Wallace at 20schevyparts.com may have a hub puller. Art 2 Link to comment Share on other sites More sharing options...
JRA Posted July 19, 2022 Share Posted July 19, 2022 Once I bought old cars, I had to buy old tools…they simplify life ! 3 Link to comment Share on other sites More sharing options...
Mark Shaw Posted July 19, 2022 Share Posted July 19, 2022 Try a search on this forum to find a source for hub pullers. Link to comment Share on other sites More sharing options...
lump Posted July 19, 2022 Share Posted July 19, 2022 I have had 10 or 15 pullers in a box for decades, gathering dust. I'll try to see if I have any with that hub diameter and thread size for you. Link to comment Share on other sites More sharing options...
lump Posted July 21, 2022 Share Posted July 21, 2022 (edited) So I went through my pullers, and checked them all with a Harbor Freight digital caliper set. None of the inside threaded pullers measured at 2 -3/8", but all of them actually tested a little smaller than any standard size. I'm no machinist, and not the best with calipers, micrometers, etc. So I tested some brand new common 3/4" threaded nuts, and they actually measure slightly smaller than a 3/4" ID. So now I'm not sure exactly what size a 2-3/8" inside-threaded hub puller ought to measure with a set of calipers. I'm getting 2.30" on the one I have in front of me. Can anyone tell me exactly what that thread size would be? Edited July 21, 2022 by lump (see edit history) Link to comment Share on other sites More sharing options...
Dandy Dave Posted July 22, 2022 Share Posted July 22, 2022 (edited) On 7/20/2022 at 10:33 PM, lump said: So I went through my pullers, and checked them all with a Harbor Freight digital caliper set. None of the inside threaded pullers measured at 2 -3/8", but all of them actually tested a little smaller than any standard size. I'm no machinist, and not the best with calipers, micrometers, etc. So I tested some brand new common 3/4" threaded nuts, and they actually measure slightly smaller than a 3/4" ID. So now I'm not sure exactly what size a 2-3/8" inside-threaded hub puller ought to measure with a set of calipers. I'm getting 2.30" on the one I have in front of me. Can anyone tell me exactly what that thread size would be? Threads are measured at the outside diameter so measuring from the inside will be smaller as you need to add the depth of the thread X 2. To know the depth, you need to know the threads per inch and look it up in a Machinerys Handbook. Or today, just google it. The info is out there somewhere on the web. Edited July 22, 2022 by Dandy Dave (see edit history) 1 Link to comment Share on other sites More sharing options...
lump Posted July 24, 2022 Share Posted July 24, 2022 On 7/22/2022 at 7:05 AM, Dandy Dave said: Threads are measured at the outside diameter so measuring from the inside will be smaller as you need to add the depth of the thread X 2. To know the depth, you need to know the threads per inch and look it up in a Machinerys Handbook. Or today, just google it. The info is out there somewhere on the web. Thanks, Dave. I am continually amazed by the increasing number of things I THOUGHT I understood, but in fact did not. The older I get, the dumber I feel. Link to comment Share on other sites More sharing options...
JohnnyNC Posted July 25, 2022 Share Posted July 25, 2022 I currently own and show an original 55 Plymouth and just pulled all the drums to inspect while doing a minor brake adjust. Without that OEM rear drum puller ($100) then I wouldn't been able to accomplish. Also the oem-kno k-off "concentric drum measuring tool" (also about $100) made dual front brake cylinder brake adjustments more precise. Love those old tools for old cars! Time savers! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now