cquisuila Posted November 8, 2021 Share Posted November 8, 2021 Hello Is it normal when i press the brake pedal, the parking lights are efficient as the stop lights ?🤨 Link to comment Share on other sites More sharing options...
JFranklin Posted November 8, 2021 Share Posted November 8, 2021 Get your stop lights working. People behind you want to know what you are doing. Link to comment Share on other sites More sharing options...
The 55er Posted November 8, 2021 Share Posted November 8, 2021 The front parking lights should not come on when you depress the brake pedal, only the rear brake lights should be operable. Link to comment Share on other sites More sharing options...
cquisuila Posted November 8, 2021 Author Share Posted November 8, 2021 41 minutes ago, The 55er said: The front parking lights should not come on when you depress the brake pedal, only the rear brake lights should be operable. it is well that i thought ! it is a court circuit ... Link to comment Share on other sites More sharing options...
RivNut Posted November 8, 2021 Share Posted November 8, 2021 It all happens within that large switch that sits on top of the steering column close to the firewall. This thing Link to comment Share on other sites More sharing options...
cquisuila Posted November 8, 2021 Author Share Posted November 8, 2021 OK eD IT is the part i have used when i just installed the warning..... i will see !! it is the purple wire i think.... Link to comment Share on other sites More sharing options...
XframeFX Posted November 8, 2021 Share Posted November 8, 2021 4 hours ago, cquisuila said: Is it normal when i press the brake pedal, the parking lights are efficient as the stop lights ? Totally separate circuits. However, I'm sure you are aware by now that the turn signals and brake indication share the same filaments of the 1157 bulbs in the rear. Link to comment Share on other sites More sharing options...
cquisuila Posted November 9, 2021 Author Share Posted November 9, 2021 (edited) and is it normal that the turn signal left and right light on the tachymeter when i depress brake pedal ? Edited November 9, 2021 by cquisuila (see edit history) Link to comment Share on other sites More sharing options...
XframeFX Posted November 9, 2021 Share Posted November 9, 2021 Only if your 4-Way Hazard switch is ON. Remember, the Turn signal indication on your Instrument Panel is connected directly to your Front Signal Lights. Link to comment Share on other sites More sharing options...
cquisuila Posted November 10, 2021 Author Share Posted November 10, 2021 yes if i push my hazard switch it lights the tachymeter (lights left and right) but if i press the brake pedal it lights the parking lights and the 2 lights signal on tachymeter i must verify the wiring on my hazard....grrrr !!:( Link to comment Share on other sites More sharing options...
RivNut Posted November 10, 2021 Share Posted November 10, 2021 When you retrofit a 4 way flasher into an older car, that is going to happen. WHY would you need brake lights AND 4 way flashers at the same time?. Link to comment Share on other sites More sharing options...
cquisuila Posted November 10, 2021 Author Share Posted November 10, 2021 (edited) yes Ed !! it is my problem in France the stop and signal lights are INDEPENDANT in USA it is common🤥 I don't want brake lights AND 4 way flashers at the same time 🤥 and more the parking lights is efficient when i depress brake pedal Edited November 10, 2021 by cquisuila (see edit history) Link to comment Share on other sites More sharing options...
RivNut Posted November 10, 2021 Share Posted November 10, 2021 I would say that unless you can somehow rig up an extra set of lights, you’re not going to be able to accomplish what you’re trying to do. Does France not have some kind of “ grandfather clause” that allows cars built before a certain date to be exempt from some regulations? Link to comment Share on other sites More sharing options...
EmTee Posted November 11, 2021 Share Posted November 11, 2021 This is why I recommended installing a period-correct aftermarket 4-way flasher unit. They are usually available on Ebay. https://www.ebay.com/itm/203681725040?hash=item2f6c607a70:g:yJAAAOSw3LVhgDhM 1 Link to comment Share on other sites More sharing options...
cquisuila Posted November 11, 2021 Author Share Posted November 11, 2021 unfortunately it will not resolve my problem to separate stop from signal lights. THANKS Link to comment Share on other sites More sharing options...
Racer-X- Posted November 11, 2021 Share Posted November 11, 2021 I'm not sure what year Riviera you have. Most GM cars from the late 1950's through the 1970's had a long single row connection for the turn signal switch on the column. The traditional (usual) wire colors are white, green, yellow, purple, brown, dark blue, light blue. The brake signal to the turn signal switch is the white wire from the brake light switch. You'll want to cut that wire and feed that as the power to the brake light filaments. If you're installing separate amber signal lights on the back for turn signals, you'll route the wiring from the 1157 bulbs in the red stop/tail/turn lamps for the turn signal to your amber signal lights. Use a wire from the white wire from the turn signal switch to power the brake light filaments in the 1157 bulbs directly from the the white wire from the brake light switch. It sounds like you're trying to just join the amber signal lamps to the brighter filaments for the 1157 bulbs. That won't quite work the way you want. This document is from a universal kit that uses the GM column switch and mostly follows the GM wire colors. It also shows how it's wired for stop/turn signal on the same bulb, and how to change it for separate amber turn signal lamps. https://smhttp-ssl-87263.nexcesscdn.net/media/productattachments/files/92972292_510489_IN_0.0_1.pdf I hope that helps. Link to comment Share on other sites More sharing options...
RivNut Posted November 11, 2021 Share Posted November 11, 2021 If you need to comply with certain regulations for separate brake and turn signal lamps, you are going to have to incorporate separate bulbs for each system and create a new entire harness to accept two separate systems. It has been such a long time since I owned my 66s and 67 that I cannot remember if each taillight housing has one or two bulbs. If the housing has two bulbs, you are half way there for your task of creating a new harness. I would bet there are others in France who own vintage American cars. Your best bet would be to ask them what they did. Link to comment Share on other sites More sharing options...
cquisuila Posted November 11, 2021 Author Share Posted November 11, 2021 (edited) it is exactly the white wire i understand i think ,in the rear, i have 4 parts - 3 lights !!!!!! for tail, lights and signal !!!!! - 1 light (on the extremity to center) for back light i think that i separate the light here with : - 1 light for the signal only - i will keep 2 lights for tail and stop together - 1 light which not changes with back light thank you Ed and Racer X Edited November 11, 2021 by cquisuila (see edit history) Link to comment Share on other sites More sharing options...
RivNut Posted November 11, 2021 Share Posted November 11, 2021 (edited) As Professor Higgins said "I think you've got it!" Or if France is like other European countries, you could have three circuits (you'd have to give up your back up lights though) One circuit - outer red - for your brake lights, one circuit - inner red - for your flashers, and in the third circuit you would put an amber bulb in your back up light housing (clear lens) for your turn signals. Edited November 11, 2021 by RivNut (see edit history) Link to comment Share on other sites More sharing options...
EmTee Posted November 12, 2021 Share Posted November 12, 2021 The '67 has three tail light bulbs on each side, however, only the two outermost bulbs support brake and turn signals. The innermost bulb is wired for parking/tail light only. The backup lights are further inboard of the three bulbs I just described. I could envision splitting-off the outermost bulb to act as tail and turn signal (remove from the brake circuit) and then have the remaining two act as brake/tail lights. Then the brake would be separated from the turn signal bulbs and the front and rear turn signals would operate the same way. Link to comment Share on other sites More sharing options...
cquisuila Posted November 12, 2021 Author Share Posted November 12, 2021 What are the difference of parking lights and tail lights please ? IN europe we have position lights. Link to comment Share on other sites More sharing options...
EmTee Posted November 12, 2021 Share Posted November 12, 2021 (edited) Tail lights and parking lights are the same thing. The tail lights are specifically the rear parking lights, or as you say, the position lights. All I was saying is all three 1157 bulbs in the rear light housing come on as tail/position lights, but only the outer two have the brake/turn signal filament connected in the wiring harness. You could modify the harness to run dedicated brake light and turn signal feeds to the rear of the car. Then, you could rewire the outermost 1157 bulb sockets to have the bright filament of the bulb connected to the turn signal feed and the dim filament remain as a position light (or disconnect, if regulations require a dedicated turn signal). The middle 1157 socket can remain as original. Connecting a jumper from the brake light wire on the center bulb to the unwired pin on the innermost 1157 bulb socket will add brake light function to that bulb. Edited November 12, 2021 by EmTee (see edit history) Link to comment Share on other sites More sharing options...
Racer-X- Posted November 12, 2021 Share Posted November 12, 2021 (edited) 2 hours ago, cquisuila said: What are the difference of parking lights and tail lights please ? IN europe we have position lights. Your question is like asking the difference between a "hood" and a "bonnet" on a car. To an American, they are tail lights, and they operate from the "running lights" circuit/fuse. To an English person (from England), they are position lights. Also, English have "indicators" where Americans have "turn signals." Adding to the confusion, to a German, "parking lights" are the position lights on the traffic side of the car (and it must only be that side) that must be left illuminated when the car is parked on a public street or road. 18 hours ago, RivNut said: Or if France is like other European countries, you could have three circuits (you'd have to give up your back up lights though) One circuit - outer red - for your brake lights, one circuit - inner red - for your flashers, and in the third circuit you would put an amber bulb in your back up light housing (clear lens) for your turn signals. Unfortunately, in European countries where amber turn signals are required, and the inspectors check that, reverse lights are also required, and the inspectors check those as well. However, I do like your solution even if it requires adding one or two clear/white "reverse lights." I think add-on afterthought "reverse lights" would be less ugly than added amber turn signal lamp assemblies. An amber bulb may be enough, or the clear (stock) reverse light lens might have to be covered/wrapped with the appropriate amber color. No offense to the OP, but the French (especially the inspectors) are very persnickety about the lights on their cars. Almost as bad as the German inspectors at the TUV. But the French do make the absolute best headlights available, so there's a positive side to that. Edited November 12, 2021 by Racer-X- (see edit history) Link to comment Share on other sites More sharing options...
RivNut Posted November 12, 2021 Share Posted November 12, 2021 5 hours ago, cquisuila said: What are the difference of parking lights and tail lights please ? IN europe we have position lights. In the United States we use tail lights when we're driving and parking lights when the car is parked and not running. BUT, they are the same bulb in the same socket. The use all depends on whether the car is being driven (at night) or being parked (at night). Very seldom to people use their "parking" lights. Link to comment Share on other sites More sharing options...
JFranklin Posted November 12, 2021 Share Posted November 12, 2021 (edited) 7 hours ago, RivNut said: Very seldom to people use their "parking" lights. The use of parking lights happned usually when the car was parked where it could cause trouble. Now their primary use is in parades to doll up the car. Many states do not allow travel with parking lamps only. The flasher has taken over the original use of parking lights. Edited November 12, 2021 by JFranklin (see edit history) 1 Link to comment Share on other sites More sharing options...
Racer-X- Posted November 13, 2021 Share Posted November 13, 2021 10 hours ago, RivNut said: The use all depends on whether the car is being driven (at night) or being parked (at night). Very seldom to people use their "parking" lights. I use parking lights a whole lot. They aren't for when the car is parked. That would be "parked lights," which is what the Germans do with the one side only lighting. I use parking lights while I'm parking, IE, driving around a parking lot or driveway at night, when I don't want to be shining headlights in the direction of pedestrians or into peoples windows. When I pull off the street or road into the parking lot, I'll tun off the headlights and put it in the parking lights position. When I'm pulling out, I'll drive to the street or road with the parking lights on, then when I'm about to pull out onto the street or road (or rural highway), I'll hit the headlights. Link to comment Share on other sites More sharing options...
cquisuila Posted November 13, 2021 Author Share Posted November 13, 2021 i must have a problem when i turn the key to on or accessory ,the tail light, licence light are on . The front lights parking are not. Link to comment Share on other sites More sharing options...
RivNut Posted November 13, 2021 Share Posted November 13, 2021 19 hours ago, Racer-X- said: I use parking lights a whole lot. They aren't for when the car is parked. That would be "parked lights," which is what the Germans do with the one side only lighting. I use parking lights while I'm parking, IE, driving around a parking lot or driveway at night, when I don't want to be shining headlights in the direction of pedestrians or into peoples windows. When I pull off the street or road into the parking lot, I'll tun off the headlights and put it in the parking lights position. When I'm pulling out, I'll drive to the street or road with the parking lights on, then when I'm about to pull out onto the street or road (or rural highway), I'll hit the headlights. That’s a nice gesture but I could not do that in any of my daily drivers, even the 90 Riviera or the 2020 EncoreGX. I would have to dismantle the Twilight sentinels on them; they all have automatic headlights that come on in the dark. Link to comment Share on other sites More sharing options...
EmTee Posted November 14, 2021 Share Posted November 14, 2021 19 hours ago, cquisuila said: when i turn the key to on or accessory ,the tail light, licence light are o Yes, that sounds like a problem. Those lights must be getting power from something that's on when ignition is on. My first guess would be the brake light feed. Link to comment Share on other sites More sharing options...
cquisuila Posted November 14, 2021 Author Share Posted November 14, 2021 ok and the switch lights ? perhaps. i put it out WITHOUT installing on board, just in TEST connecting Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now