avgwarhawk Posted July 1, 2020 Share Posted July 1, 2020 There are many posts concerning thermostats or more so overheating issues. The good. The bad. The ugly. Has anyone used a Stant Superstat or high flow thermostat? What was the end result? Link to comment Share on other sites More sharing options...
avgwarhawk Posted July 2, 2020 Author Share Posted July 2, 2020 No response. Well, I installed a Stant Superstat high flow 180. I have not put any miles on it to report if it works better than the standard 180 thermostat. I will let you know! 1 Link to comment Share on other sites More sharing options...
Joseph P. Indusi Posted July 4, 2020 Share Posted July 4, 2020 I installed one on my 53 Special 45 R about 8-10 years ago. Compared to the standard thermostat it does offer a larger area when opened for coolant flow. I noticed that the car did run cooler. I sourced mine from Bob’s. Never had any problem with it since. Joe 1 Link to comment Share on other sites More sharing options...
Dan O Posted July 4, 2020 Share Posted July 4, 2020 I was told by my mechanic this week that 160 or 180 does not make a lot of difference BUT he did say the better thermostats these days have a little hole drilled in them to allow a gradual flow of water rather than a burst on opening. He said he would drill a hole in mine if it did not have one in the Superstat. He's got it on a dyno right now! Link to comment Share on other sites More sharing options...
avgwarhawk Posted July 5, 2020 Author Share Posted July 5, 2020 (edited) The difference in the two temps makes a difference in that winter driving the heater will warm the cabin better. Also, the hotter the motor the more efficient it will be. I have seen stats with bleed holes but these were designed to bleed air from the system. Was not so much a slow release of coolant into the system. The superstat has a heavier duty spring that opens slowly with more control as claimed, but also provides a larger opening. Edited July 5, 2020 by avgwarhawk (see edit history) 1 Link to comment Share on other sites More sharing options...
edinmass Posted July 5, 2020 Share Posted July 5, 2020 The reason for thermostats was simple......to prevent oil sludge accumulation. Back in the day oil would stick to the inside of the engine looking like you blew insulation into it. It would cake up that bad. As oil improved there was much less reason to have a thermostat, and then hot water heaters became more common with the introduction of antifreeze. Since the 50’s better fuel required warmer operating temperatures.......and then add in the clean air act.....and that’s when you see cars starting to operate at 205-210 degrees. 1 Link to comment Share on other sites More sharing options...
Ben Bruce aka First Born Posted July 5, 2020 Share Posted July 5, 2020 18 hours ago, Dan O said: I was told by my mechanic this week that 160 or 180 does not make a lot of difference BUT he did say the better thermostats these days have a little hole drilled in them to allow a gradual flow of water rather than a burst on opening. He said he would drill a hole in mine if it did not have one in the Superstat. He's got it on a dyno right now! Must be a youngish mechanic. Ben 2 Link to comment Share on other sites More sharing options...
Bloo Posted July 5, 2020 Share Posted July 5, 2020 (edited) That hole is to let the coolant fill up to the thermostat so the engine doesn't have to overheat to "burp" when it first runs with new coolant. Sometimes it's a little check valve instead of a hole. Edited July 5, 2020 by Bloo (see edit history) 2 Link to comment Share on other sites More sharing options...
avgwarhawk Posted July 5, 2020 Author Share Posted July 5, 2020 1 minute ago, Bloo said: That hole is to let the coolant fill up to the thermostat so the engine doesn't have to overheat to "burp" when it first runs with new coolant. Sometimes it's a little check valve instead of a hole. That's what I have known these small holes are for. 1 Link to comment Share on other sites More sharing options...
old-tank Posted July 5, 2020 Share Posted July 5, 2020 On 7/2/2020 at 1:00 PM, avgwarhawk said: No response. Well, I installed a Stant Superstat high flow 180. I have not put any miles on it to report if it works better than the standard 180 thermostat. I will let you know! I hope you have a fantastic report. The thermostats that I have been using work as designed, but (and it may be some other problem with the cooling system design) my factory air cars do not like speeds faster than 65mph if the outside temperature is above 95*. Link to comment Share on other sites More sharing options...
Joseph P. Indusi Posted July 5, 2020 Share Posted July 5, 2020 Old-tank: Your 55 Buick’s probably have a generator so you are doing very well with AC on these beauties. Sixty- five mph is a good speed given you have drum brakes on your 4000 pound cars. Can’t think of why 65 mph creates a problem for your cars. Happy 4th of July to all! Joe Link to comment Share on other sites More sharing options...
avgwarhawk Posted July 5, 2020 Author Share Posted July 5, 2020 2 hours ago, old-tank said: I hope you have a fantastic report. The thermostats that I have been using work as designed, but (and it may be some other problem with the cooling system design) my factory air cars do not like speeds faster than 65mph if the outside temperature is above 95*. I'll keep you posted. Link to comment Share on other sites More sharing options...
Dan O Posted July 5, 2020 Share Posted July 5, 2020 10 hours ago, Ben Bruce aka First Born said: Must be a youngish mechanic. Ben Ben - not young, perhaps even older than you! But I probably mis-quoted him on the purpose of the hole in the thermostat. Link to comment Share on other sites More sharing options...
Ben Bruce aka First Born Posted July 6, 2020 Share Posted July 6, 2020 4 hours ago, Dan O said: Ben - not young, perhaps even older than you! But I probably mis-quoted him on the purpose of the hole in the thermostat. If he is older than me he is ancient. I am 83. I would never run an engine cooler than 180. I run a 195 as is in my straight eight. Ben Ben 2 1 Link to comment Share on other sites More sharing options...
avgwarhawk Posted July 9, 2020 Author Share Posted July 9, 2020 (edited) On 7/5/2020 at 11:35 AM, old-tank said: I hope you have a fantastic report. The thermostats that I have been using work as designed, but (and it may be some other problem with the cooling system design) my factory air cars do not like speeds faster than 65mph if the outside temperature is above 95*. Willie, I can not detect much of a difference if any. The temp gauge to me is more of a "suggested" temp at the current driving conditions. The needle did still climb at highway speeds but did not continue to climb as I have experienced with the standard stat. I was rolling at 70 mph. 85 degrees. At a stop with engine at idle the needle climbed to the top of the white normal line. She did the same with my standard 180 stat. No change there. When I returned to the garage I let her run until the needle went to the top of the normal range. Using a infa-red temp tester at idle with the needle at the high range of normal the temp at the stat housing 202 degrees. Head at the port for the temp gauge probe 180 degrees. Overall, not much of a difference. However, I'm glad to note when at a light or stop/go traffic, the needle at the high side of normal she is at 202 degrees or there about. The temp never climbed any higher. Picture at idle and just pulled into the garage. Driving at city street speed the needle is over the N. At highway speeds this is the position she will climb. Did not go any further. Guesstimating she is running at 190 degrees at 70 mph. 85 degrees today. Edited July 9, 2020 by avgwarhawk (see edit history) 1 1 Link to comment Share on other sites More sharing options...
avgwarhawk Posted July 10, 2020 Author Share Posted July 10, 2020 On 7/5/2020 at 11:35 AM, old-tank said: I hope you have a fantastic report. The thermostats that I have been using work as designed, but (and it may be some other problem with the cooling system design) my factory air cars do not like speeds faster than 65mph if the outside temperature is above 95*. Willie, Second look. I drained the radiator and block. It was time. No flush. Added new green coolant recommend for our older cars. 50/50 mix. She ran steady temp at 40-50 mph. Climbed a bit at 65 but climbed no more. Needle returned to position at off highway speeds. At idle the needle did not climb to the top of normal. Although the superstat and new coolant did not show significant changes it did offer more steady predictable cooling as indicated by the temp needle. The infrared temp meter shows 202 at the t-stat housing, at idle, and temp needle at the high end if normal as indicated on the gauge. I'm still of the opinion that our gauge set up is a "suggested" temp. Although the needle is heading to the H and in the normal range it's still running well under boiling point. Your AC unit is no doubt working hard and making some significant heat at 65 mph. Question is, what is the true temp of the cooling system at those speeds? Our basic temp gauges we will never know. Maybe next time your are in that situation attempt to get a reading with a infrared temp gun. As a side note, I'm not so sure the temp probe in the head is the best spot. Today's cars the port to the coolant is usually somewhere near the t-stat housing. 1 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now