jan arnett (2) Posted January 14, 2020 Share Posted January 14, 2020 I used a Mitt once and it worked well. Link to comment Share on other sites More sharing options...
8E45E Posted January 14, 2020 Share Posted January 14, 2020 56 minutes ago, jan arnett (2) said: I used a Mitt once and it worked well. The city workers used mitts to paint all the light poles every few years. Very fast and worked well with 100% coverage. Craig Link to comment Share on other sites More sharing options...
V16 Posted January 15, 2020 Share Posted January 15, 2020 This car was brush painted when new. The car is a one off custom Packard 336 Sport Touring by Rollston. It is all original. When you look at the surface in the right light you can see the marks left by the camel hair brush. In 1927 the custom shops had not yet switched over to the new fangled spray gun. Old world craftsmen who had developed their skills on horse drawn carriages weren't about to change a winning formula! 4 1 Link to comment Share on other sites More sharing options...
auburnseeker Posted January 15, 2020 Share Posted January 15, 2020 I used Epifanes on this 26 foot Dodge Watercar I put a new transom on in my driveway. I painted the entire bottom over on the trailer with a creeper. With a little thinning it flowed amazingly well, but I had to give it a couple of coats to get the best coverage. I was amazed how smooth it came out. There were few if any brush strokes and I wasn't even using a really expensive brush. It laid much better than the varnish which I wet sanded and buffed when done. I never touched the bottom. The transom came off in one piece so I could use it for a hanger in my garage, but it was and is today individually planked. When I made the sign for my business I used the same Epifanes paint and transom for a pattern. It lasted very well with just some fading that could have easily been buffed back after 5 years of full time southern facing sun exposure. I saved it and will hang it in the new shop when I get it more finished. 3 Link to comment Share on other sites More sharing options...
1937hd45 Posted January 15, 2020 Share Posted January 15, 2020 Not being a boat guy I have to ask why that extra back piece is there? Bob Link to comment Share on other sites More sharing options...
auburnseeker Posted January 15, 2020 Share Posted January 15, 2020 That was the transom I took off, that's why all the bungs are pulled as I was going to pull it plank by plank, but it came out easier due to some rot in the framing as a unit so I was able to leave it intact. If you look close you can see the bottom corner was rotten and came apart when I was taking it out. Fortunately the planks on the bottom weren't. Link to comment Share on other sites More sharing options...
adalah Posted January 15, 2020 Share Posted January 15, 2020 (edited) never experienced it. but this is a very interesting discussion to follow Edited January 15, 2020 by adalah (see edit history) Link to comment Share on other sites More sharing options...
Michael-Resurrector Posted January 17, 2020 Share Posted January 17, 2020 In my rented commercial property I can only use rattle can paint, I doubt anyone can tell the difference. I have gotten very good at it. 1 Link to comment Share on other sites More sharing options...
Terry Wiegand Posted January 17, 2020 Share Posted January 17, 2020 Here is a photo of our 1920 Model K-46 Buick Coupe. The body on this car was painted with a brush when it was built. I have been told that the finish was colored varnish. I am not sure how many coats were applied, but sanding occurred between the applied coatings. Buick did not go to lacquer type finishes until the 1925 models. Someone will correct me if I have the year incorrect. Everything on this car that could go through a drying oven was baked enamel. After 101 years the body finish is definitely needing attention. Terry Wiegand South Hutchinson, Kansas 2 Link to comment Share on other sites More sharing options...
auburnseeker Posted January 17, 2020 Share Posted January 17, 2020 11 hours ago, Michael-Restomod said: In my rented commercial property I can only use rattle can paint, I doubt anyone can tell the difference. I have gotten very good at it. Trickiest thing I have found with spray cans is keeping the wet line. I painted the glass doors on my shop but by the time you made it all the way around it had tacked just enough to not get a good overlap. I figured out by the 3rd door, that if I started and stopped at the handle area, you couldn't really see it as your site line was obstructed by the handle so you didn't pick it up. Nice thing is when you are done you can wet sand it all and buff it. I've done that many times with smaller parts and you can achieve a mirror finish pretty easily. Link to comment Share on other sites More sharing options...
Michael-Resurrector Posted January 17, 2020 Share Posted January 17, 2020 Also another trick I use to get rid of the lines is just let it get dusty, then use the dust with a rag to buff the surface and just that takes my lines out, then a gentle buff. Rattle can is not as thick, so don't over buff it, just a light buff. Link to comment Share on other sites More sharing options...
lump Posted January 17, 2020 Share Posted January 17, 2020 7 hours ago, auburnseeker said: Trickiest thing I have found with spray cans is keeping the wet line. I painted the glass doors on my shop but by the time you made it all the way around it had tacked just enough to not get a good overlap. I figured out by the 3rd door, that if I started and stopped at the handle area, you couldn't really see it as your site line was obstructed by the handle so you didn't pick it up. Nice thing is when you are done you can wet sand it all and buff it. I've done that many times with smaller parts and you can achieve a mirror finish pretty easily. Interesting. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now