alsfarms Posted October 12, 2018 Share Posted October 12, 2018 I am looking into casting my own radiator cap to replace a well weathered original Bakelite radiator cap. I know this same process has been completed many times. Could someone share with me the best material to use that is easily castable, UV resistant, can stand temps to about 220 and be machinable in order to fit and glue the threaded brass cap into the finished casting. I see that McMaster-Carr has a Black product that can stand temps to 180 deg. F but do not know how UV resistant that material is. The McMaster-Carr P/N for this material is: 8644K55. Please share your knowledge and experience. Al Link to comment Share on other sites More sharing options...
Spinneyhill Posted October 12, 2018 Share Posted October 12, 2018 (edited) What do the people recasting steering wheels use? Looking..... http://qualityrestorations.com/our-process/ uses a clear urethane tinted to the right colour. Edited October 12, 2018 by Spinneyhill (see edit history) Link to comment Share on other sites More sharing options...
jpage Posted October 12, 2018 Share Posted October 12, 2018 I would contact some of the urethane rubber/epoxy suppliers and ask what they would recommend as there is a wide range of product out there. There are also many Youtube videos and making mold and casting parts which are very informative. Here's a couple to start with Alumilite.com (800-447-9344), Smooth On Rubber (610-252-5800), Polytech (800-858-5995) and BJB Enterprises. Just google casting resin and I'm sure more will come up. Good luck! Link to comment Share on other sites More sharing options...
Gary_Ash Posted October 13, 2018 Share Posted October 13, 2018 How about using Devcon Plastic Steel Liquid? It is pourable, gets hard and strong, will take the heat and hot water, is machinable, and can be polished and painted. It might be better to cast the liquid over the threaded brass part rather than trying to glue it in after casting. The mold can be made from flexible urethane or silicone rubber using your old part (cleaned and polished/painted) as a master. Don’t forget to use mold release before pouring the Plastic Steel. Link to comment Share on other sites More sharing options...
Friartuck Posted October 14, 2018 Share Posted October 14, 2018 (edited) I have used both Smooth-On Urethanes for molds and their clear (which is tintable) for the actual part. I have also used Alumilite with moderate success. The Alumilite I used went past its shelf life, so the mediocre results may have resulted due to age, not sure which to blame it on, but Smooth-On solved my problem anyway so I never pursued a fresher batch of Alumilite. These two articles may help: http://www.secondchancegarage.com/public2/small-parts.cfm http://www.secondchancegarage.com/public4/casting-taillights-1.cfm I also have used DEVCON products (Rubber) with good success, so Gary's suggestion should be a good one. The material from Mcmaster-Carr is not DEVCON. Edited October 14, 2018 by Friartuck (see edit history) Link to comment Share on other sites More sharing options...
mrpushbutton Posted October 15, 2018 Share Posted October 15, 2018 If you can at all machine it from a solid piece (sheet goods) if the details aren't that fussy use Garolite from McMaster-Carr. We make Duesenberg parts out of it that were originally Bakelite. https://www.mcmaster.com/garolite 1 Link to comment Share on other sites More sharing options...
Spinneyhill Posted October 16, 2018 Share Posted October 16, 2018 4 hours ago, mrpushbutton said: If you can at all machine it from a solid piece (sheet goods) if the details aren't that fussy use Garolite Garolite is not suitable for use outdoors so wouldn't be brilliant for a radiator cap unless carefully painted to exclude UV light. It is fibre-glass sheet reinforced epoxy. Link to comment Share on other sites More sharing options...
MochetVelo Posted February 11, 2019 Share Posted February 11, 2019 How about Bondo (polyester body filler)? Check this thread out (from MTFCA Forum). Go to the post by Rich Eagle. Here is a photo Rich posted where he made Bakelite handles for a Model T Tudor using wood and scuplty clay for the molds. Phil 1 Link to comment Share on other sites More sharing options...
alsfarms Posted February 12, 2019 Author Share Posted February 12, 2019 Hello Phil, Thanks for the heads up on work done by Rich Eagle. He is a craftsman. I could sure ask him a few questions about his process not only on the handles but also on the Model T Brass radiator side he built. Al Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now