ken1007 Posted November 10, 2016 Share Posted November 10, 2016 (edited) weatherstrip glue There is a need to "fuse" together the butt end of rubber weather strip to make a good seal on a rear window; available only in one continuous length. Some time ago, I heard of a 3M glue that is designed to "fuse" the butt end of weather strip with bonding similar to vulcanization. It's reportedly a small, expensive tube that work exceptionally well and is easy to use. Does anyone know of such a product? Ken, Deltaville, Va Thanks to all, just ordered 3 M super glue, hope it works. Ken, Deltaville, Va Edited November 11, 2016 by ken1007 (see edit history) Link to comment Share on other sites More sharing options...
jpage Posted November 10, 2016 Share Posted November 10, 2016 Depending on the type of rubber the weatherstrip is made from, you can use any CA glue made specifically for rubber. If it has a high silicone content, as some material does, you need to use silicone to glue it together as CA (Super glue) will not stick to silicone based material. Link to comment Share on other sites More sharing options...
vintchry Posted November 10, 2016 Share Posted November 10, 2016 Ken, I have used Super Glue with very good results. I am aware of the 3M product you speak of but also am at a loss for the name. Have you looked at the 3m Website? Rob Link to comment Share on other sites More sharing options...
Curti Posted November 10, 2016 Share Posted November 10, 2016 You can use 3M black weatherstrip adhesive available at NAPA. But I would use super glue. Link to comment Share on other sites More sharing options...
R Walling Posted November 10, 2016 Share Posted November 10, 2016 (edited) I always use 3M Super Black Weatherstrip Adhesive 08008 Is very tough stuff. When installing weather strips cut the strip a little long (about1/4 or 3/8") and apply adhesive to the ends and let the natural pressure hold it together. I have used it to hold SS mouldings on when you can't get them to hold tight to the body. I applied the adhesive and held the moulding in place with a 2X4 until it hardened. Make sure that you clean off any adhesive on the paint or it is forever! (use lacquer thinner) It is also good for emblems that the little pins have broken off, or they are stripped, apply from both sides of the panel. Edited November 10, 2016 by Roger Walling (see edit history) Link to comment Share on other sites More sharing options...
mike6024 Posted November 10, 2016 Share Posted November 10, 2016 You can go onto the 3M website and ask them your question, by clicking on the "Chat" button. http://3mauto.com/products/adhesives-sealants#JdOQLa7vEgPdduZT.97 http://3mauto.com/products/adhesives-sealants/3m-super-glue-gel-08122.html#x7Dz03sUD7CLXx9p.97 It might be this super glue gel you are thinking of but I'm not sure. Most of the weatherstrip adhesive bonds rubber to metal, and can also bond rubber to rubber but may not be optimum for that. Super Glue Gel 08122 Link to comment Share on other sites More sharing options...
Vila Posted November 10, 2016 Share Posted November 10, 2016 I have always used the 3M 08581 product, which is called "Black Super Weatherstrip and Gasket Adhesive". Among other applications, I have joined the ends of my Triumph TR4 Trunk gasket with it and it has not come apart over the past 3 years. Like other have said, I cut the gasket approximately 3/8 inch longer than needed and used the pressure between the two pieces along with some blue painters tape to hold it until it dried. 1 Link to comment Share on other sites More sharing options...
Spinneyhill Posted November 12, 2016 Share Posted November 12, 2016 I used cyanoacrylate to make a new O-ring for the pool sand filter. The "rubber" rope was about 3 mm diameter or a little bigger. It was strong enough to seal the top of the filter when I screwed it back on. It was about 200 mm diameter. Link to comment Share on other sites More sharing options...
Curti Posted November 12, 2016 Share Posted November 12, 2016 Cyanoacrylate is superglue or as some call it crazyglue Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now