-
Posts
1,268 -
Joined
-
Last visited
-
Days Won
1
Content Type
Forums
Gallery
Events
Everything posted by RockinRiviDad
-
Be careful. Those micro switches will crack from over tightening. Mine was cracked for a long time from what looks like over tightening by the previous owner. The years of heat under the hood dried them out & makes them brittle. What I recently discovered, when I fixed my cracked switch & tried to finally adjust it right, was that the wires to the micro switch are also dried out & firm/stiff. The wires run down along side the throttle linkage coming out of my firewall. There is a clip (looks stock/original) that holds the wire to the linkage. The wire is so firm/stiff that I noticed I was able to push up on the wire & it actually held my micro switch in the adjusted position with the screw loose. So I added a couple of zip ties (I like zip ties š), then tighten down my micro switch
-
Thank u. But I donāt need any of those suggestions to hear my solenoid click. I can hear that while laying on my fender & pushing on the micro switch. I can hear the solenoid click over the micro switch click. Itās apparent that my solenoid clicks. But that doesnāt tell me if my vanes are switching pitch
-
Are u saying that from a complete stop & with my zip tie depressing my micro switch (high stall) when I try driving away at a ānormalā rate of speed I should feel the kick like when the kickdown kicks in at high speed? NOT on my car. Is that a troubleshooting clue telling me the vanes in my convertor arenāt switching??
-
U may NOT like the idea of being in high stall during acceleration. I didnāt. I tried it & HATED it. Zip tie the micro switch in the depressed position & go for a drive. Itās an old switch. Donāt kill it by cranking down on the zip tie. U can see it doesnāt need much pressure to hold it. So be gentle with the zip tie. It felt like I was starting off from a stop in 3rd gear. It felt super sluggish. Excuse my description, I donāt have the proper terms. But all torque converters are effective at āXā RPM/MPH (I donāt know the numbers). High stall from a dead stop our converters are useless. But with the hot rod switch in place u can flip the switch to give u high stall while driving & itās like another kickdown/passing gear whenever u want. I hope I explained that correctly
-
My understanding is that it doesnāt affect takeoff. Once u depress the accelerator pedal with any amount of pressure the micro switch goes back to what it was like when u had it out of adjustment. I drive with mine out of adjustment. It feels better to me. To each his own. But now I am considering added the hot rod switch (for lack of a better term) under the dash. Wiring diagram courtesy of Russ Martinās website
-
1965 Grille removal...yep, all studs are out...
RockinRiviDad replied to moran75's topic in Buick Riviera
-
@Schmiddy
-
I installed new springs in the front also. good call on checking my installation. Hopefully that is the issue fingers crossed š¤š¼
-
new springs may not solve an uneven ride issue. There are also spacers that sit under your springs. Maybe called āspring perchesā?? my car had 1/2ā spacers/perches under the driver side rear spring when I took the old springs out. These spacers/perches do not look DIY. They are round, made of metal & have a large grove carved In them where the end of the coil rests in. I replaced my old springs with brand new (1ā lower than standard H2 specs, 2ā lower total), 400 pound spring rate H2 springs from CSS & my car still sat uneven. It was lower on the driver side. So I shoved that 1/2ā spacer/perch back in & itās still uneven. My thought was to find a slightly larger spacer/perch to solve my problem. But thatās as far as Iāve gotten
-
Very exciting. Good luck. I see that u installed what looks like the Holley Hyperspark too. U will probably have RFI/EMI issues. I did. Tech support had me wrap my dizzy in tin foil & it worked. That was just to isolate/troubleshoot where is was coming from. They said my air cleaner was acting as an antenna between the Sniper ECU, Hyperspark & Holley coil (old style coil, mounted in stock location). So they had me add a ground wire to the base of my air. Problem solved. Weird. Iām learning a lot.
-
I do happen to have a friend in high places. Nice bracket. So have u had a chance drive it & test your creation? Cruise control? Hmmmā¦now thereās an idea. I never thought of that. I will look into that
-
Congrats, I agree. Looks like very clean work. Looks like a high dollar build done right (unlike my shoddy a$$ DIY work š). It also looks brand new, as in ānot drivenā yet. Have u had a chance to drive it? I am interested to hear how your setup performed. It doesn't look like the throttle geometry was addressed. Your throttle linkage looks parallel to valve covers. We had to raise ours up some so that it would pull Sniper linkage from slightly higher. U might find u have the same issues as we did. Keep us posted
-
Your funny...Iām glad this helped. Congrats on your Sniper install I decided to make my throttle mounting point on the bracket a little closer to the sniper due to my aftermarket air cleaner. It used to hit my hood when hood was closed. I found a low profile air cleaner base which allowed my air cleaner to sit lower. A lower air cleaner base meant I didnāt have much room to change the geometry of my throttle linkage by simply raising it up, I also had to go inward. That & a little persuasion with my ball peen hammer on the air cleaner base & wah-lah...it worked Somewhere in this thread I added another idea for someone to try. That was to simply cut off the the mounting hole tab, rotate it 180 degrees & weld it. I think that would have eliminated the need for u to shorten your linkage with extra bends. Iām glad u posted your details. The guys who follow our lead will make less & less mistakes. DONāT forget to keep checking your TPS (throttle position sensor). Keep us posted on the bracket u fab up. Maybe u will create something better than mine
-
SP micro switch fix causing popping in speakers
RockinRiviDad replied to RockinRiviDad's topic in Buick Riviera
So ur thinking the relay I ordered will not work? -
SP micro switch fix causing popping in speakers
RockinRiviDad replied to RockinRiviDad's topic in Buick Riviera
What do u mean by āClass-Aā? I ordered a relay my buddy suggested I try. Still waiting for it to show up. Is that what u mean by a āregulated PSā? -
Where was it living for the last 54 years? š¤·š»āāļøš¤·š»āāļø
-
SP micro switch fix causing popping in speakers
RockinRiviDad replied to RockinRiviDad's topic in Buick Riviera
I checked the amp ground. But Iāll check to see if my EQ has one too. Thx -
SP micro switch fix causing popping in speakers
RockinRiviDad replied to RockinRiviDad's topic in Buick Riviera
It wonāt allow me to add video š¤·š»āāļø -
SP micro switch fix causing popping in speakers
RockinRiviDad replied to RockinRiviDad's topic in Buick Riviera
Yes, the micro switch is working right now. I will post a little video. Iām excited about it working. But now that I cruised the car around with the SP working, Iām not sure I like it. It sits at a light/stop sign unless I depress the throttle. I might add the Hot Rod switch under the dash š¤·š»āāļø Lately, I have been attacking all the stupid little things that need attention on my car. Both SP micro switch AND KD switch always had bare wires which had me thinking would arc & not allow them to work right. But I never heard āpoppingā from my speakers. Now that I have repaired the wires I get the āpoppingā. I can only assume that the both SP & KD did not work before. Now they work & itās causing the āpopā. If I am understanding this correctly, a test wire from battery to SP connection would simply activate the solenoid to test if it works, right? In the this little video u can clearly hear the micro switch click but u canāt hear the solenoid activate. But I can clearly hear it in person. The relay my buddy suggested was not for the SP micro switch. It was for the audio system power source. By unplugging all audio (except power supply) & still getting a āpopā tells us it might be related to where the installer got power for my audio. A quick hunt for said power source revealed that he tapped into a power wire from my ignition. Correct me if Iām wrong, but I think adding a relay for my audio power will still be a safer option for audio even if the āpopā doesnāt go away. -
SP micro switch fix causing popping in speakers
RockinRiviDad replied to RockinRiviDad's topic in Buick Riviera
My radio is not hooked up. I play music thru my phone which connects to my speakers with one of those Bluetooth thingys. I tried disconnecting all of my audio equipment & the popping is still there. My buddy suggested I add a relay to the power wire feeding my audio. He thinks I might have a ādirty power sourceā as he describes. He explained that a relay may provide a clean source & hope that solves the popping -
Finally, I fixed my micro switch. It had a hairline crack in the micro switch body that would not allow me to adjust it. A little epoxy, a small clamp to hold it together while epoxy dried & all seems wellā¦NOT!! Now I am getting a loud āpopā or ācrackā like sound from my speakers each time I touch the throttle as micro switch clicks. This happens in park at idle or at a stop sign/light & I touch the pedal. I can also recreate the sound in my garage with the key in Aux position & I touch the throttle pedal with my hand Any suggestions on what to check would be kindly appreciated.
-
what was used to mount it?
-
Without looking at the manual, I donāt know where itās āsupposeā be mounted at the factory. But my buddy mounted his in the glove box on his 65
-
For lack of a better term, we will call the sheet metal attached to the bottom of the grill a ābumper fillerā. There are bolt/screws to the left & right of the bumper filler to the hold it to the fenders. Take those out & the bumper filler will come off with the grill. Then u can take the whole thing to your work bench, take off all the nuts on the stubs u are fighting, pull off the bumper filler & kick those studs asses š¬
-
Two years ago I upgraded to a quick ratio steering box after my stock box started to leak. I didnāt need one of the fancy boxes. I simply went to a shop that rebuilds steering gear boxes & told him what I was after. His idea was to comb thru his stock pile of used Saginaw boxes with the same bolt pattern & rebuilt it. We found one with a quicker ratio & wha-lah...no leaks plus quicker ratio...I cant remember what the new box came from tho Fast forward to the present time: I had clearance issues with my headers hitting the passenger side upper control arm. Now I noticed clearance issues with the steering gear box. It dented my headers...UGH!! So I dropped the box, used a cutoff wheel & cut the protruding nub off. Doing this kind of work while laying on the garage floor is nooooo fun
- 444 replies
-
- 65 rivi
- build thread
-
(and 2 more)
Tagged with: