Bloo Posted March 26, 2020 Share Posted March 26, 2020 Which? The jet? It unscrews. Don't try with anything less than a perfectly fitting flat blade screwdriver. Carter probably had a special socket tool. Link to comment Share on other sites More sharing options...
jw1955buick Posted March 26, 2020 Author Share Posted March 26, 2020 No the bugered up check ball retainer thing also does this look like the right acc pump for the ‘55 wcfb? 1 Link to comment Share on other sites More sharing options...
old-tank Posted March 26, 2020 Share Posted March 26, 2020 The pump looks like it will work...leather will last longer. Check ball retainer thing: "dude, you're screwed"...maybe, maybe not. I have buggered them myself. I used a drill bit with tip ground flat in a good variable speed drill until I got enough out to pry with a homemade tool; some came out when the drill grabbed. Just don't let the drill touch the sides! 1 Link to comment Share on other sites More sharing options...
avgwarhawk Posted March 26, 2020 Share Posted March 26, 2020 There are pointed sets for prying. Run to Harbor Tools and get a pick and hook set. https://www.harborfreight.com/Mini-Pick-and-Hook-Set-63697.html?ccdenc=eyJjb2RlIjoiMzk0ODAzMTciLCJza3UiOiI2MzY5NyIsImlzIjoiMC45OSIsInByb2R1Y3RfaWQi OiIxMjg2NyJ9 &cid=paid_google|||63697&utm_source=google&utm_medium=cpc&utm_campaign=&utm_content=&gclid=Cj0KCQjwpfHzBRCiARIsAHHzyZoH2aCQaRDuHsb-xAwUuWzCEg4el46Q93mI-S7degGpLPknEzyKQwkaAkfXEALw_wcB Link to comment Share on other sites More sharing options...
jw1955buick Posted March 26, 2020 Author Share Posted March 26, 2020 I’ve got those, it’s in there so tight it bent the cheapo hook, that’s the first thing I tried sounds like I’m down to the drill bit, I was afraid of that Link to comment Share on other sites More sharing options...
jw1955buick Posted April 27, 2020 Author Share Posted April 27, 2020 took carb apart bench tested the acc pump with some gas, squirted fine pushing it up and down, good steady stream out of the two top nozzles, when I installed on the car, it doesn't work like that, it stumbles hard right off the bat, if you increase throttle super super slow it comes up as it should but if you try to apply in any normal fashion, it instantly stumbles. I pulled the little pump cover off and noticed when I tried to give it gas, the needle bar setup was popping right up at the same time it bogged, loosing vacuum with piston perhaps, when I increased throttle real slow, the needle bar came up slowly Fuel line checks out clean and fuel pump is putting out a real good pulse of fuel so am I loosing vacuum somewhere? Still hard to start but idles okay once you get it. Help please Link to comment Share on other sites More sharing options...
carbking Posted April 28, 2020 Share Posted April 28, 2020 (edited) The "top hat" check valve in the WCFB generally requires a special tool. http://www.thecarburetorshop.com/Carter_tools.htm Scroll down to T109-279. No, I am not trying to sell you one. I wanted to show the picture to then be able to paint a word picture, as the tool CAN be fabricated if your machinist skills are sufficient. The end of the tool looks like a pipe die. It is tapered from large diameter at the bottom to small diameter somewhat higher up inside the tool. The inside of the tool is threaded like the die. The tool is used by sliding something with a hole (the handle end of a large adjustable end wrench will work) over the tool, and the threading the tool on the OUTSIDE of the "top hat" after the center post has been broken. Once securely screwed onto the top hat, use the handle end of the adjustable end wrench like a slide hammer against the cross bar at the top of the tool to remove the top hat. It works, EVERY TIME! I doubt very seriously you will get much service from that imitation accelerator pump. EDIT: For those who might wonder about the price of this tool compared to other tools on the list. Carter did NOT include this tool in ANY of the Carter tool kits. It had to be ordered separately, and it was VERY expensive at the time. Because of the cost to Carter, Carter superseded T109-279 with T109-290 (no, I don't have one of these pictured, it was also available only ala carte). Unfortunately, the T109-290 DID NOT WORK maybe 40 percent of the time, and T109-279 was still required. Jon. Edited April 28, 2020 by carbking (see edit history) 1 Link to comment Share on other sites More sharing options...
buick5563 Posted April 28, 2020 Share Posted April 28, 2020 I use mini long needle nose pliers to grab and twist those hat / ball retainers. I then reinstall with a deep 1/4” drive socket that fits the outer edge. Link to comment Share on other sites More sharing options...
carbking Posted April 28, 2020 Share Posted April 28, 2020 Mike - the needle-nose pliers will work maybe 50 percent of the time. The other 50 percent you twist out the center bar. The T109-290 mentioned above is similar. Will try to find one in my inventory tomorrow and picture it. Jon. 1 Link to comment Share on other sites More sharing options...
jw1955buick Posted April 28, 2020 Author Share Posted April 28, 2020 (edited) I was able to stake that cover down, what was interesting was the hole the check ball is in, it looked a little tight, I guess it just goes up and down slightly, anyway, that wasn't a big deal. I bought a very old carb kit on ebay and used the leather pump in it hoping to make the difference, no change whatsoever. So is the idea so far improper acc pump seal? where does the vacuum come from to hold the vacumeter piston down against the spring? Edited April 28, 2020 by jw1955buick (see edit history) Link to comment Share on other sites More sharing options...
buick5563 Posted April 28, 2020 Share Posted April 28, 2020 6 hours ago, carbking said: Mike - the needle-nose pliers will work maybe 50 percent of the time. The other 50 percent you twist out the center bar. The T109-290 mentioned above is similar. Will try to find one in my inventory tomorrow and picture it. Jon. Believe, I’ve done that. Then had to dental pick the remainder. I was just throwing my two cents in. Especially since my T 109-290 is currently not owned by me. 😁 Link to comment Share on other sites More sharing options...
carbking Posted April 28, 2020 Share Posted April 28, 2020 (edited) The website has been updated with a picture of the other tool, but due to the technology challenged photographer, difficult to see. Here is a better picture: http://www.thecarburetorshop.com/T109-292U-1.jpg Actually, the part number for the complete tool is T109-292U, which consists of T109-290 and T109-291. Jon. Edited April 28, 2020 by carbking (see edit history) Link to comment Share on other sites More sharing options...
carbking Posted April 28, 2020 Share Posted April 28, 2020 (edited) The website has been updated with a picture of the other tool, but due to the technology challenged photographer, difficult to see. Here is a better picture: http://www.thecarburetorshop.com/T109-292U-1.jpg Memory gets worse daily! Here is an article on this subject I did several years ago, and completely forgot: http://www.thecarburetorshop.com/Carter-WCFB-check-ball-tools.htm Jon. Edited April 28, 2020 by carbking (see edit history) Link to comment Share on other sites More sharing options...
carbking Posted April 28, 2020 Share Posted April 28, 2020 14 hours ago, jw1955buick said: I was able to stake that cover down, what was interesting was the hole the check ball is in, it looked a little tight, I guess it just goes up and down slightly, anyway, that wasn't a big deal. I bought a very old carb kit on ebay and used the leather pump in it hoping to make the difference, no change whatsoever. So is the idea so far improper acc pump seal? where does the vacuum come from to hold the vacumeter piston down against the spring? No offense meant, but is the pump DISCHARGE check valve in place? The ball is the intake check valve; the discharge check valve should be under the center screw in the primary venturi. Jon. Link to comment Share on other sites More sharing options...
jw1955buick Posted April 28, 2020 Author Share Posted April 28, 2020 No offense at all, I was waiting for your reply, I’ll double check that Link to comment Share on other sites More sharing options...
jw1955buick Posted April 28, 2020 Author Share Posted April 28, 2020 (edited) Okay I can’t figure out what you’re talking about, can’t find a reference to that in the manual, I do know that I have the needle under the pump jet and the check ball under the hat underneath the acc pump, is it in the pictures I provided earlier in the post? are you talking about the “plug and gasket “ in the above photo at right? That’s in there Edited April 28, 2020 by jw1955buick (see edit history) Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now