Ralph55 Posted August 18, 2019 Share Posted August 18, 2019 (edited) Does anyone know the temperature range of the gauge in 1955 or 1956 Buicks? My 1955 Super shut down the engine while driving when the temperature reached N (the center position of the gauge). After 20 minutes of cool down the engine started again. When checking the actual temperature of the radiator (with a BBQ thermometer 😋 ) when the needle pointed to N I found out that's just 150 deg Fahrenheit! With my 66 GTO the regular temperature is 170 deg. I tried to find the water temperature range in the shop manual - but no luck there: Edited August 18, 2019 by Ralph55 (see edit history) Link to comment Share on other sites More sharing options...
old-tank Posted August 18, 2019 Share Posted August 18, 2019 Water temperature. Upper limit of the gauge is about 200*F. Your Super did not shut down the engine...it shut down probably due to vapor lock. All 55's need an electric fuel pump mounted near the tank due to the highly volatile available fuel. Check the temp with an IR temperature gun at the thermostat housing. Temperature will depend first on the thermostat installed and later on environmental temperature. 1 1 Link to comment Share on other sites More sharing options...
Ralph55 Posted August 18, 2019 Author Share Posted August 18, 2019 Thanks for the hint, Tank 🙂 Never heard of a vapor lock before - but I'm here to learn... I added an electric fuel pump in the engine compartment. What would be the reason to mount it near the tank? The current thermostat is brand new and was replaced during the engine revision in winter. So when the pump is electrical - can a vapor lock still occur? I think the pump keeps pushing fuel to the carb - even if the fuel between pump and carb is vaporized. Link to comment Share on other sites More sharing options...
SpecialEducation Posted August 18, 2019 Share Posted August 18, 2019 ‘56 was the first yeat for permanent (ethylene glycol) anti-freeze. There was a service bulletin in late ‘56 that explained that with the change, customers were complaining about running hot, because the water temp needle was buried in the red. Buick engineering’s solution: Remove the red from the gauge. If it’s not boiling over, it’s not overheating. Link to comment Share on other sites More sharing options...
old-tank Posted August 18, 2019 Share Posted August 18, 2019 14 minutes ago, Ralph55 said: Thanks for the hint, Tank 🙂 Never heard of a vapor lock before - but I'm here to learn... I added an electric fuel pump in the engine compartment. What would be the reason to mount it near the tank? The current thermostat is brand new and was replaced during the engine revision in winter. So when the pump is electrical - can a vapor lock still occur? I think the pump keeps pushing fuel to the carb - even if the fuel between pump and carb is vaporized. Vapor lock occurs on the suction side of any pump. Any pump can push fuel, but cannot always pull fuel well. An engine compartment mounted pump is useful to prime the carb on a cold engine, but is no better than the stock mechanical pump to prevent or treat vapor lock. 1 1 Link to comment Share on other sites More sharing options...
Ralph55 Posted August 18, 2019 Author Share Posted August 18, 2019 Hm... I see - moving it away from the engine compartment keeps the pump cool. Do you think it would help if I wrap the fuel line and pump with https://www.thermotec.com/products/sleeving/express-sleeves ? Link to comment Share on other sites More sharing options...
NTX5467 Posted August 18, 2019 Share Posted August 18, 2019 I believe that the OEM engine thermostat was a 160 degree F unit, unlike the more common 180 degree F units which others used. Hence, the middle of the "N" range should probably be near that 160 degree temperature. Which also means that the "H" line will be lower than what came later, too. When a liquid is placed in a low-pressure situation, it vaporizes easier. Putting the pump at the REAR is closer to the supply tank and can lessen the "low pressure vaporization" issues. If put near the engine (as many hot rodders used to do), that puts the whole fuel line in the "low pressure" area. Even hot rodders from the '60s or so put the pump on the frame rail near the tank. Compared to other makes in the middle '50s, Buicks seemed to have more issues with vapor lock on hot days. Not particularly from engine heat, but from heat radiated from the pavement/road surface the car was driving/parked on. As Old-Tank has found out, it doesn't take a 8psi electric pump to do the job. You can get an IR heat gun thermometer at Harbor Freight or Northern Tools or similar. Even the 1000 degree F models are not more than $30.00 now. MANY uses in the automotive and residential areas of things! NTX5467 1 Link to comment Share on other sites More sharing options...
Ralph55 Posted August 18, 2019 Author Share Posted August 18, 2019 (edited) Reflecting on Tank's input and having a look at the new arrangement of the fuel line after motor revision (Image 1) it seems the metal line right over the engine block creates a "grill enviroment" 😁 So if the engine heats up it "grills" the fuel inside the pipe over the whole length. Probably the pipe literally soaks up the heat because being made of metal 😱 Pump to filter Tank to pump (it's a low pressure one) Edited August 18, 2019 by Ralph55 (see edit history) Link to comment Share on other sites More sharing options...
old-tank Posted August 18, 2019 Share Posted August 18, 2019 42 minutes ago, Ralph55 said: Reflecting on Tank's input and having a look at the new arrangement of the fuel line after motor revision (Image 1) it seems the metal line right over the engine block creates a "grill enviroment" 😁 So if the engine heats up it "grills" the fuel inside the pipe over the whole length. Probably the pipe literally soaks up the heat because being made of metal 😱 You are correct. Fuel in that line will probably boil, but a pump mounted back at the tank will push fuel and any vapor into the carb. That Airtex pump you have is junk. It will soon fail (how do you spell tow truck?). This Carter Pump is what I use. Link to comment Share on other sites More sharing options...
Ralph55 Posted August 18, 2019 Author Share Posted August 18, 2019 cool! 😍 Next week I'll replace the Airtex and relocate the pump. Then I'll use a thermo-insulated hose for the last mile! Link to comment Share on other sites More sharing options...
old-tank Posted August 18, 2019 Share Posted August 18, 2019 1 minute ago, Ralph55 said: Then I'll use a thermo-insulated hose for the last mile! It will have no effect unless you use it on the short line between the tank and the electric fuel pump. Link to comment Share on other sites More sharing options...
Ralph55 Posted August 19, 2019 Author Share Posted August 19, 2019 (edited) @old-tank the recommended Carter fuel pump P60504 is discontinued. 😪 The successor is P90091 which only makes half of the gallons per hour. Do you think 15 GPH are still enough? The P60504 had 30 GPH... Though the Carter info tells me P90091 is the replacement part for P60504, my guess would be https://outlawspeed.com.au/shop/fmp60430 Edited August 19, 2019 by Ralph55 (see edit history) Link to comment Share on other sites More sharing options...
old-tank Posted August 19, 2019 Share Posted August 19, 2019 10 minutes ago, Ralph55 said: @old-tank the recommended Carter fuel pump P60504 is discontinued. 😪 The successor is P90091 which only makes half of the gallons per hour. Do you think 15 GPH are still enough? The P60504 had 30 GPH... Bummer. 15 GPH should be enough unless racing or pulling a trailer. "last one on ebay" Link to comment Share on other sites More sharing options...
Marty Roth Posted August 21, 2019 Share Posted August 21, 2019 Electric fuel pumps are a fine "pusher"' but a very weak "sucker". For this reason, your supplemental electric pump should be mounted in-line as low, and as close to the fuel source (tank) as reasonable. Some also recommend adding a relay from your oil pressure switch so that if the car is stalled, you'll not flood the carb - or if the car is in a wreck and the engine quits, you'll not be adding fuel to a possible fire- Overkill? - maybe, but as a son of a career firefighter I believe in precautions. Link to comment Share on other sites More sharing options...
Ralph55 Posted August 21, 2019 Author Share Posted August 21, 2019 @Marty Roth I did already add that kind of "emergency shutdown" relay to the pump 👨🚒 1 Link to comment Share on other sites More sharing options...
Ralph55 Posted August 22, 2019 Author Share Posted August 22, 2019 Oh... after a quick check: I didn't install the safety relay a year ago - because I couldn't find the oil pressure switch back then 😬 After doing some research I think there is only an oil pressure sensor for the gauge - but no switch because there's no separate warning light. I found one article on how to "retrofit" the 322 with an electric oil pressure switch using the 'little tapped hole just above the oil filter mount'. Do I have to get an oil pressure switch or would it work if I just attach the wire of the relay reading "to oil pressure switch" to the pressure sensor? Link to comment Share on other sites More sharing options...
old-tank Posted August 22, 2019 Share Posted August 22, 2019 THIS would be easier than installing a "T" fitting and then trying to fit lines in that very inaccessible location. On 8/20/2019 at 7:44 PM, Marty Roth said: Some also recommend adding a relay from your oil pressure switch so that if the car is stalled, you'll not flood the carb - Even when installed it seem that you will have not power to the fuel pump until the engine is running...seems there would have to be a "momentary switch" to bypass?? Link to comment Share on other sites More sharing options...
avgwarhawk Posted August 22, 2019 Share Posted August 22, 2019 (edited) Wire in an fuel pump inertia cut off switch. $17.00 Amazon. Hotwin First Inertia Switch Vehicle Crash Sensor Standard Ignition Electric Fuel Pump Edited August 22, 2019 by avgwarhawk (see edit history) 1 1 Link to comment Share on other sites More sharing options...
Marty Roth Posted August 22, 2019 Share Posted August 22, 2019 2 hours ago, old-tank said: THIS would be easier than installing a "T" fitting and then trying to fit lines in that very inaccessible location. Even when installed it seem that you will have not power to the fuel pump until the engine is running...seems there would have to be a "momentary switch" to bypass?? Needs to be installed like a 1990s era FoMoCo setup so in the event of a crash the fuel will not be pumping to support a blaze Link to comment Share on other sites More sharing options...
Marty Roth Posted August 22, 2019 Share Posted August 22, 2019 2 hours ago, avgwarhawk said: Wire in an fuel pump inertia cut off switch. $17.00 Amazon. Hotwin First Inertia Switch Vehicle Crash Sensor Standard Ignition Electric Fuel Pump Yes, that is what I was referring to - thanks Link to comment Share on other sites More sharing options...
Ralph55 Posted August 22, 2019 Author Share Posted August 22, 2019 (edited) After a 20 miles highway drive I sampled the temperatures along the fuel path - it turned out the fuel is probably boling inside the metal fuel filter close to the carb which draws heat from the engine block obviously! As there are two filters (one is right after the pump) I'll remove the one right before the carburetor. To avoid the fuel boils inside the carb bowl I'll add an additional insulating base gasket for the Carter WCFB. Edited August 22, 2019 by Ralph55 typo (see edit history) 1 Link to comment Share on other sites More sharing options...
old-tank Posted August 22, 2019 Share Posted August 22, 2019 2 hours ago, Ralph55 said: After a 20 miles highway drive I sampled the temperatures along the fuel path - it turned out the fuel is probably boling inside the metal fuel filter close to the carb which draws heat from the engine block obviously! As there are two filters (one is right after the pump) I'll remove the one right before the carburetor. To avoid the fuel boils inside the carb bowl I'll add an additional insulating base gasket for the Carter WCFB. It won't make any difference. A pump back at the tank will push fuel and any vapor along into the carb. Now an attempt at insulating the base of the WCFB might be of some benefit to address percolation (fuel boiling in the carb and flooding the manifold) after a hot run. But if using the stock air cleaner assembly, there is not enough room between the hood and air cleaner for anything too thick. Hey, I tried all of those remedies, including clothes pins on the fuel line: vapor lock occurs on the suction side only! Link to comment Share on other sites More sharing options...
Ralph55 Posted August 22, 2019 Author Share Posted August 22, 2019 (edited) Sorry, I did forget to mention that my Carter pump arrived from the US yesterday and I'll replace the Airtex in the engine compartment with the Carter back at the tank. Great thing aside: Because amazon International couldn't meet the delivery date they didn't charge shipping - so the pump was really a bargain... 😁 But are you really sure with the suction side? At 1:54 it''s boiling between pump and carb --> Edited August 22, 2019 by Ralph55 typos (see edit history) Link to comment Share on other sites More sharing options...
Rosiesdad Posted August 22, 2019 Share Posted August 22, 2019 I run a 12psi pump near the tank. Then to a tee at the filter by the carb. From tee one side goes to carb. the other side of tee returns by 1/8" copper tube to tank filler tube neck. No more vapor lock at any temperature. Good luck! Link to comment Share on other sites More sharing options...
Ralph55 Posted August 22, 2019 Author Share Posted August 22, 2019 You mean a vapor separator with a return tube? Like this one from Mopar... Link to comment Share on other sites More sharing options...
old-tank Posted August 22, 2019 Share Posted August 22, 2019 32 minutes ago, Ralph55 said: But are you really sure with the suction side? At 1:54 it''s boiling between pump and carb Yep, really sure! The pump at the back will push all that into the carb and it will continue to run fine. And get rid of all that rubber and plastic chit and replace as much as possible with metal. It makes me plumb sick when someone becomes a crispy critter. Link to comment Share on other sites More sharing options...
Rosiesdad Posted August 24, 2019 Share Posted August 24, 2019 I'm not running a separator. Bypassed the mech pump. The brass tee has pipe thread fittings so there is a nipple to pipe thread on the inlet. Outlet to carb is a union pipe to pipe thread. On top the return line to tank is a pipe to Swagelok 1/8" tubing. The constant gas flow keeps it cool. Have had zero vapor lock since this upgrade. I now have stainless 1/8" return line for durability. I drilled a 1/8" hole high in the filler neck for return. Good luck! Phil 1 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now