trimacar Posted December 22, 2019 Share Posted December 22, 2019 The binding for the edge is a bias binding, in that when fabricated the material to make it is cut an an angle to fabric weave, thus "bias". I do understand your angst, it's a little tricky, but one learns to feed and slightly stretch binding in such a way they there are a lot of little wrinkles, and no big wrinkles, on an outside curve..... Good luck, looks like you're making good progress....I see a lot of relief cuts, be careful with those as half an inch too far and rework ensues.... Link to comment Share on other sites More sharing options...
MikeC5 Posted December 23, 2019 Share Posted December 23, 2019 Thanks David, I did cut the binding material on a 45 bias. On the tight outside corners I ended up carefully cutting 'pie slices' out every 1/4 inch to keep things flat. I bought new 'pull-a-dot' anchors and fasteners for the side flaps since my top frame was missing a few of the anchors. The originals have a wood screw thread so I assume there was solid wood inside the sockets. That is no longer the case, in these locations anyway, so I've got to come up with an alternate plan to get the anchors to hold. The anchors are available with an 8-32 stud instead of the wood screw thread so I can weld up the holes and re-drill/tap but I'd like to avoid that option. I'm going to try Helicoil inserts and cross my fingers... Link to comment Share on other sites More sharing options...
MikeC5 Posted December 23, 2019 Share Posted December 23, 2019 The helicoils worked perfectly. Link to comment Share on other sites More sharing options...
MikeC5 Posted December 28, 2019 Share Posted December 28, 2019 (edited) Well I got the rear curtain on there. Not perfect where it wraps around the sides but I'm hoping I can smooth out those areas with a little heat. Edited December 31, 2019 by MikeC5 (see edit history) 4 Link to comment Share on other sites More sharing options...
jan arnett (2) Posted December 29, 2019 Share Posted December 29, 2019 I noticed that you are putting the top on first. How do you plan on tacking your interior on the rear tack rail Link to comment Share on other sites More sharing options...
MikeC5 Posted December 29, 2019 Share Posted December 29, 2019 (edited) My understanding is that the cushions and seat backs and the inside rear trim pieces are upholstered separately. The seat backs go on first and have fittings that hook under the aft sheet metal wrap around and then bolts secure the lower portion. I don't have any good photos of the rear seat details at the moment but it works similar to these of the front seat back. The side pieces use the same idea. Edited December 29, 2019 by MikeC5 (see edit history) Link to comment Share on other sites More sharing options...
MikeC5 Posted January 1, 2020 Share Posted January 1, 2020 (edited) I hope everyone enjoyed this New Year's day! I have a question for David with regard to laying out the top panel seams. You mentioned earlier in this thread: Quote To mark the two seams on the top panels, I put a piece of welting cord on the top of the pad, held with a single thread stitch to pad at each bow and in between each bow, and mark the cord at random 8-12 inch lengths with a marker. These will be my marks to sew the panels together. Lay the main center panel on top, stretch it front to back and temporarily tack, pull taut sideways then mark from cord. Do the same with the side panels. Join these marks with lines on table, leave 1/4 inch sewing allowance, cut a small vee in fabric at mark, and use these to line up when sewn. TRUST YOUR MARK, don't second guess and think they're wrong when laid on table. You then fold over and top stitch this seam, always with the top stitch toward the center of the car. I understand that you want the pads to hide the seam that joins the top panel and the side panels and I want to make the seam parallel to the inboard edge of the pads(?). I've got my marking cord stretched between the front and rear bow, 1 inch outboard of the pad inboard edge at each of these bows (a straight line between these two anchor points). The cord position at the 2nd and 3rd bows comes closer to the pad edges than 1" so I need to move the cord to achieve the 1" spacing to edge of pad for bows 2 and 3 and then do a stitch to hold it in place at those points. Does this sound correct? Also, when you say fold over and top stitch with top stitch toward center of car, do you mean the fold should point to center of car (see photo)? I did some practice pieces of top stitching and am also curious about the location of the stitch closest to the fold. I seems easiest to position the stitch such that the fold is made immediately adjacent to the stitch since the stitch then controls where the fold occurs. Some sources show leaving some distance between the stitch and fold. How do you normally do it? As always, you advice is greatly appreciated. Edited January 1, 2020 by MikeC5 (see edit history) Link to comment Share on other sites More sharing options...
trimacar Posted January 1, 2020 Share Posted January 1, 2020 (edited) Hi- you may have to adjust the cording location so that there's not a zig-zag when you view from the front. The exact dimension from edge of pad isn't really important, as long as seam is hidden by pad. I must have misspoken somehow. The stitch itself is toward the inside of the car, the fold is outside of the stitch. The fold that you show with the arrows "to the center of car" is backwards, the "open" edge of the folded seam should be to the outside of the car. Think about rainwater, you don't want to trap it in the middle, you want it to roll over and off the seam. In other words, the very last diagram you show, to the right would be the outside of the car. I only use one top stitch, and the "tail" isn't as big as you show. After you sew the two pieces together, fold it over snugly (but not pulling so much the first sewn thread shows) and then run the top stitch about 3/16 inch from the edge of the fold. If you practice with the foot on your sewing machine, you'll find a reference from the edge of the foot to the folded seam, and that helps you keep it straight and true. Use bonded polyester thread that's UV resistant, otherwise your thread will fade. Hope all that makes sense. Edited January 1, 2020 by trimacar (see edit history) Link to comment Share on other sites More sharing options...
MikeC5 Posted January 2, 2020 Share Posted January 2, 2020 Thank you David. Your help is invaluable. I am using the UV resistant polyester thread (138 size). Strong stuff! Link to comment Share on other sites More sharing options...
MikeC5 Posted January 15, 2020 Share Posted January 15, 2020 I'm almost ready to sew the top seams. Good thing I have a helper... Link to comment Share on other sites More sharing options...
trimacar Posted January 15, 2020 Share Posted January 15, 2020 I'm trying to come up with something top related like a bow wow, but it's just not coming. He seams to be a nice puppy! Link to comment Share on other sites More sharing options...
MikeC5 Posted January 15, 2020 Share Posted January 15, 2020 He's 7 years old and 100 lbs and thinks he's a lap dog.... He loves to ride in the Dodge. Link to comment Share on other sites More sharing options...
MikeC5 Posted January 22, 2020 Share Posted January 22, 2020 I got the seams sewed up. I can say that any extra time spent setting up a large table(s) at equal height to feed and receive the sewn top as it goes through the machine is well worth it. I tried to get by with a little less than that and it just makes keeping it going straight that much harder. Overall, they came out pretty straight but not error-free. Link to comment Share on other sites More sharing options...
trimacar Posted January 22, 2020 Share Posted January 22, 2020 I must say I don’t quite understand what I’m looking at in your picture. On a touring top, when fabric is laid on a table as you show, there are no continuous straight lines, and the side panels aren’t rectangles in any way, nor will it lay flat. Just don’t understand what you’re showing nor what you’ve done. It also looks like, though hard to tell, you have rounded edge of seam facing toward inside of car, when it should be to outside. Hope I’m wrong and you’ve done it correctly... Link to comment Share on other sites More sharing options...
MikeC5 Posted January 23, 2020 Share Posted January 23, 2020 Hi David, It is hard to tell from the photo but the seams are sewn with orientation as in the diagram. I cut the side panels as rectangles for simplicity; I know a fair amount will be trimmed off once I get it on the car and mark where the edges should be. I thought you sewed the top and side panels together before trying to mark where to trim the sides so I made sure I left extra trim allowance. Laid on the table, the seam may appear to be a single straight line but it isn't. The seam does change angle slightly at the 2nd and 3rd bow and the seams are further apart at the rear bow than at the front (by roughly 3 inches), forward end is closer to the camera. But they are straight lines from 1st to 2nd bow, 2nd to 3rd, 3rd to 4th. The first photo showing the black side up after sewing may be a little confusing because the edge panel on left is partly hanging off edge of the table. I'm not sure I understand why it wouldn't lay flat at this point. The seams did end up at my string locations. Link to comment Share on other sites More sharing options...
trimacar Posted January 23, 2020 Share Posted January 23, 2020 (edited) Yep, pictures can be deceptive. Hope it works out well. The side panels are not rectangles, by the way. You have to wrap the fabric around the sides, mark to top panel accordingly, if anything they are elongated triangles, otherwise they won’t wrap around to rear bow correctly. As with any upholstery work, easy to show in person, hard to describe in words. Edited January 23, 2020 by trimacar (see edit history) Link to comment Share on other sites More sharing options...
Hubert_25-25 Posted February 16, 2020 Share Posted February 16, 2020 (edited) Hi Mike, I am following your post with great interest and you are doing a great service posting these details as you go. There are a couple of detail items that I think need to be clarified. I am about to start on the top for my 1925 Buick, and my son's father in law has a 1922 Dodge Touring so I know your car fairly well. This goes back to Jan's question. 1) On the Buick - and likely the Dodge, both seat backs are upholstered to the car. You can remove the seat bottom, but not the seat back. The back of the seat is tacked to the top side of the seat wood. There is also a wood strip screwed to the wood frame under the seats. The leather at the base of the seat back is tacked to the frond side of this wood. The seat side panels are also tacked to the inside side of the lower wood. 2) The bowdrill on the back of the car - I think it should be on the back side of the rear bow, and on the back side of the wood that is attached to the top of the rear toneau sheet metal. The bowdrill cloth covering on the rear bow should be visible all the way around the bow and not just on the ends. This would allow you to install the leather seat covering to the top of the back wood and cover it with hidem(or the early style hidem with black tacks). It also leaves the 2 rear top straps exposed. Sorry for the late response but I am just now reading this thread as I am about to embark on the same mission you are on. Hugh Edited February 16, 2020 by Hubert_25-25 (see edit history) Link to comment Share on other sites More sharing options...
MikeC5 Posted February 17, 2020 Share Posted February 17, 2020 (edited) Hi Hubert, Thank you for the interest. It may be different on a '22 Dodge than what I found with the '25 as far as the upper rear seat back. Although I am not 100% certain, it appears to me that the seat back was designed to be upholstered and then installed (I think my seats still had the original leather/horsehair too). Like the upper front seat back I had attached photos of earlier, there is a tack strip on back side of the spring assembly so the leather can go up and over and tacked on the back side (you can kind of see this in last attached pic). As it also shows for the front seat back, the rear seat back has hooks that engage the tub inner edge to hold it in place (and bolts hold the lower portion to captured nuts in the tub, see attached). The rear side pieces work the same way. Unfortunately, curved wood segment that bolts to the top of the rear tub was missing and so this piece of evidence was not there and I saw no evidence of wood down on the floor pan as in your photo. I would welcome hearing from anyone who can confirm how their '25 was put together. The rear side pieces work the same way as described for seat back. It would seem that being able to upholster the seats separately from the body assembly would be advantageous from a production viewpoint but that's just a guess. You are correct about the rear inner curtain. I did initially try to attach it to the rear side of rear bow but it was impossible to get it stretched out wrinkle free because it can't be moved independent of the outer curtain (you have to drive tacks through both). I finally gave up and did it as shown. It would be nice to learn how a pro would do it... As for the bottom of the inner curtain, I copied what I observed on a '25 I saw at Hershey one year (attached earlier in this thread). Actually, if this was correct, it would jive with the seat back being upholstered separately. I need to get some good photos of the rear seat back.... Edited February 17, 2020 by MikeC5 (see edit history) Link to comment Share on other sites More sharing options...
nearchoclatetown Posted February 17, 2020 Share Posted February 17, 2020 While I forget how it was done I believe the answer would be in the video the DBC sells. It is a video that shows much of how the early cars were built from factory footage. It even says how much leather and horsehair was used every day. Link to comment Share on other sites More sharing options...
MikeC5 Posted February 17, 2020 Share Posted February 17, 2020 I'll have to search that out. Thanks! Link to comment Share on other sites More sharing options...
Hubert_25-25 Posted February 23, 2020 Share Posted February 23, 2020 (edited) Mike, You are lucky that it appears your seat backs are upholstered like a modern car and can be removed. Mine are old school. Dodge had a lot of advancements. The wood window frame that came out of my Buick had six 3 1/2" wide jute straps. Three for the frame to top bow support and three for the frame to bottom wood support. The back window, glass, bowdrill, and jute straps are attached to the back canvas first on the work table. In the parts book this is called the “Back Curtain Assembly”. The jute straps and the inner bowdrill were installed first on the back side of both the upper top bow and lower wood. .Then you would tack on the back canvas. The jute straps basically support the rear window, as this is not really the job of the rear canvas. This would leave the two top bow support straps exposed in the car. Hugh Edited March 16, 2020 by Hubert_25-25 (see edit history) 1 Link to comment Share on other sites More sharing options...
MikeC5 Posted March 1, 2020 Share Posted March 1, 2020 Hi Hugh, That's a good diagram of the set up and is essentially what I've got with the exception of the inner curtain going to the forward side of rear bow and the canvas wraps around to cover the wood window frame with the frame I have. I first attached the support straps to the wood frame, rough cut the canvas rear curtain and then marked the window location (making sure I had extra material to allow centering it when attaching the rear curtain assembly to car). I then cut the window opening, attached canvas rear curtain to window frame (a little contact cement and then staples on the inner rabbet where window is inserted). Next the glass went in and then the inner (bowdrill) curtain attached and inner window trim. It was quite tricky to get this whole rear curtain assembly onto the car. I found getting the inner curtain correctly adjusted to minimize wrinkles while at the same time, getting the support straps correctly positioned and the canvas in position to be nigh well impossible, thus my decision to attach the inner curtain on the forward side of the rear bow (since it could then wait until the canvas and support straps were in position and stapled). Link to comment Share on other sites More sharing options...
Hubert_25-25 Posted March 6, 2020 Share Posted March 6, 2020 (edited) Hi Mike, This is another detail that I have been working on this week. This is how they did the front windsheild seal on the Buicks. My car was missing the sheetmetal piece so I have been getting a lot of help from others. One front piece shows nails (should be screws) but it shows the batting in the front. Hugh Edited March 6, 2020 by Hubert_25-25 (see edit history) 1 Link to comment Share on other sites More sharing options...
Hubert_25-25 Posted March 6, 2020 Share Posted March 6, 2020 (edited) This is a cut away view of how this front top seal functions. Edited March 6, 2020 by Hubert_25-25 (see edit history) 1 Link to comment Share on other sites More sharing options...
MikeC5 Posted March 7, 2020 Share Posted March 7, 2020 Hi Hugh, Very interesting how this was done on the Buick. I think it's a bit more elegant than the flap that hangs down over the top of the windshield frame. As long as the bends are 2 dimensional, it shouldn't be too difficult. Are you going to find a shop with a roller and brake to make or make up something in wood to form it? Link to comment Share on other sites More sharing options...
Hubert_25-25 Posted March 11, 2020 Share Posted March 11, 2020 Hi Mike, A lot of street rod shops have brakes. Some attic duct work companies too. I am going to go to a person that is local that has a brake on Friday. I thought about a wood buck as well, which would be my second option. Top materials were not very long lasting. This metal piece was usually rusted after a while, and then thrown out when the replacement top came. I think a lot of the aftermarket tops had a front flap sewn on to keep the water out. Not sure if any of them worked very well. This style also works better with not interfering with the wind shield wiper. This is a photo of my sheet metal prior to bending. I made a template so that I can check my bending as I go. By the way, I did a little more inspection of the rear window installation and I modified the drawing at the top of this page. Hugh 1 Link to comment Share on other sites More sharing options...
STUDE48 Posted March 21, 2020 Share Posted March 21, 2020 If you go to YouTube, look up engles coach shop. He di a 5 part video series on a collapsible buggy top and how to build one without patterns. All the principles are the same. Link to comment Share on other sites More sharing options...
MikeC5 Posted March 23, 2020 Share Posted March 23, 2020 That was a good set of videos. He really slows things down so you can understand each step. I wish I had seen that before I got the final top piece sewn together... Link to comment Share on other sites More sharing options...
MikeC5 Posted January 30, 2022 Share Posted January 30, 2022 I finally find myself with some free time to get back on this project. One thing I haven't been able to find any detail on is trimming the edges of the top along each side. I've looked at many photos of different tops and it appears a separate piece of material is sewn along the edge to reinforce it, This is my guess at how this is constructed but I'm hoping to learn the preferred method. Link to comment Share on other sites More sharing options...
STUDE48 Posted January 30, 2022 Share Posted January 30, 2022 this may hav been done to sew in a web strap and pretty it up Link to comment Share on other sites More sharing options...
STUDE48 Posted January 30, 2022 Share Posted January 30, 2022 also may have been a flap to seal up the side curtains better Link to comment Share on other sites More sharing options...
Hubert_25-25 Posted January 30, 2022 Share Posted January 30, 2022 (edited) Mike, The edge of the convertible top is treated like the edge of a side curtain. The edge is always reinforced with a second layer of top material. This is a banding 2 1/2" wide. On this top, the outermost edge is folded over to the underside. It is then sewn near the outer edge. Then the excess top material is trimmed to make a nice edge that you see inside the car. A second stitch is used near the other edge of the reinforcing strip. This is then trimmed after sewing. I have also seen where the top edge is not folded over and a U shaped piece of bias binding is used to create the outer edge. Sometimes this is done in a contrasting color. The reinforcing strip is made in the same manner. Hugh Edited January 30, 2022 by Hubert_25-25 (see edit history) Link to comment Share on other sites More sharing options...
MikeC5 Posted January 31, 2022 Share Posted January 31, 2022 Thanks guys. Hugh, is this your finished edge that is visible from inside the car or is there another piece that covers it? It appears the top material folds over one edge of the reinforcement piece (which is made from top material with black side down)? I'll have to review your top curtain notes and see how you did it there. Link to comment Share on other sites More sharing options...
Hubert_25-25 Posted January 31, 2022 Share Posted January 31, 2022 (edited) Mike, Yes, this is the finished edge on the inside. The lowest point in that photo (just below your arrow) is the single snap at the very rear of the upper fabric of the top. That is why I provided a photo of each side of the rear of the top. That rear flap is at the very back of the top and that curved area (with the arrow) is hidden from view by the back section of the top. Depending on the radius of the curvature will dictate if the fold over fabric on the inside would require those relief cuts. Notice that in the lowest part, there are also relief cuts, but they are on an inside curve rather than an outside curve so the cut pieces overlap and there is no gap between the cuts. On the sides of the top it is all straight or fairly straight, so no cuts required. I think even with that light radius, I did not really need to add that cut, but it did not show. Attached are more photos of an original 1925 Buick top. This is the back section or back curtain. Hugh Edited January 31, 2022 by Hubert_25-25 (see edit history) Link to comment Share on other sites More sharing options...
trimacar Posted January 31, 2022 Share Posted January 31, 2022 If one uses a two-fold binding (folded on each edge) then relief cuts aren’t needed and it looks “finished” on both sides. A little more difficult to sew than the single fold binding shown in pictures above, as no room for error. I find single edge razor blades are the easiest way to neatly trim reinforcing piece, pulling on tail and carefully moving blade as one goes. Change blades often. Also, I’d use a matching thread if inside is tan or black. Not criticism, Hugh, just observations. I admire anyone doing early upholstery, takes great patience…. 2 Link to comment Share on other sites More sharing options...
Hubert_25-25 Posted January 31, 2022 Share Posted January 31, 2022 I can't stress the importance of a good pair of scissors for anyone wanting to tackle upholstery. I can recommend Gingher brand 10" bent Knife edge trimmers. They are a little over $50, but they cut like butter. With certain fabrics, just push them thru the fabric and they cut beautifully. Even at just the tip. I tried using fresh razor blades to cut as David suggested but I just couldn't make it happen and I had better luck with my scissors. Photos of "2 fold binding" below. This is an option. This is another original 1925 Buick "Burbank" top. The point I want to make is that there are 2 methods of trimming the top edge. 2 fold binding was used on the more expensive tops in the Buick line up. For the bread and butter cars, the top were trimmed as I did my car as shown above. You can always make it prettier, but prettier is not always how they left the factory. 1 Link to comment Share on other sites More sharing options...
MikeC5 Posted January 31, 2022 Share Posted January 31, 2022 Thanks for the tips Gentlemen. A quality pair of new scissors is a good idea as well. Link to comment Share on other sites More sharing options...
trimacar Posted February 1, 2022 Share Posted February 1, 2022 Enjoy the sharing of information and tools needed….high quality scissors are a must as noted… Link to comment Share on other sites More sharing options...
MikeC5 Posted August 15, 2022 Share Posted August 15, 2022 I'm finally trying to get back to this. As David noted, I clearly didn't do the step with the cording properly and I'm pretty sure this is why I'm having this problem. You can see the puckering at two locations since there is excess material there. I'm not sure I should try and stretch the whole thing more (I don't want the straps to slacken). Not sure what else I can do but to cut the thread and try to sew it up again. 1 Link to comment Share on other sites More sharing options...
Hubert_25-25 Posted August 16, 2022 Share Posted August 16, 2022 Mike, I believe this is where the error was made. What was done here was just making a wider piece of fabric with a wide center section. These 3 pieces need to be made from a pattern first that is laid on the car and marked. Then the top material replaces the pattern and you make similar markings. That would be a lot of work to remove all the stitching. IMO I would consider using the center section to make 2 new side pieces, and buy enough material to make a new center section. But let me show the process. SEAM MARKING First we locate the main seams – on the top and on the back curtain. Typically the back curtain seams and the top seams overlap on the rear bow. Usually, the rear bow has cut outs and recesses to accommodate the seams as both seams stacked is 6 layers of fabric. On the Buick, these lay in the rear strap notches cut into the rear bow. You can also lay them next to each other so the stack of the seam material is not so tall. To mark the two seam locations for the top panels, put a piece of 3/16” welting cord stretched on the top of the pad. My top is narrow and the top seams are 42” wide at the front and 46 ½” wide at the rear. Hold the cord with a single thread stitch to the pad at each bow and in between each bow. Mark the cord at random 8-12 inch lengths with a marker. These will be the marks to sew the panels together. If you are not sure where these seams should be, ask a fellow owner that has your car, how wide their top seams are front and rear. 3/16” cord hand sewn every couple of inches to each top pad (below). Notice the black marks added at 8-12 inches. Doing the top in Poly: These next photos will show how I use 4 mil poly first because you can see thru it. Sailrite also sells "Dura Skrim" which I think has additional benefits for checking squareness during pattern lay out. https://www.sailrite.com/Dura-Skrim-2-Patterning-Material-74 Lay plastic as the main center panel on the bows, stretch it front to back and temporarily tack it. It should be the same width as the stayfast roll. Pull the plastic taut sideways then transfer the seam lines and the spacing marks from the 3/16” cords. There should not be a big dip in the center of the main panel. Remove the center panel. Do the same with the side panels, with the following exception. - Review convertible top photos to determine how you want the sides of the top to look – especially at the rear as different year vehicles have varied side trim and side curtain details. - Leave a couple of inches of extra fabric as we will not “trim” the sides until after the seams are stitched. - Stretch and move the side panel to find the location where the least amount of wrinkles and excess occur. It is critical that the outer side edge of the top panel hang straight down and does not have puckers in the fabric above the doors. I had to pull the side panels at the front towards the middle of the car to remove the waviness in the fabric that is hanging down over the doors. - Drive tacks (I use thumbtacks with large heads as they leave a smaller hole for this step) to ½ depth as necessary to achieve the best look and least amount of excess fabric. Doing the top in Stayfast : Lay the plastic patterns on the stayfast. This should give you a good basic size for each panel. Lay Stayfast on the main center panel on the bows, stretch it front to back and temporarily tack it. Pull the Stayfast taut sideways then transfer seam lines and the marks from the 3/16” cords. There should not be a big dip in the center of the main panel. Remove the center panel. Do the same with the side panels, with the following exception. - Review convertible top photos to determine how you want the sides of the top to look – especially at the rear as different year vehicles have varied side trim and side curtain details. - Leave a couple of inches of extra fabric as we will not “trim” the sides until after the seams are stitched. - Stretch and move the side panel to find the location where the least amount of wrinkles and excess occur. It is critical that the outer side edge of the top panel hang straight down and does not have puckers in the fabric above the doors. I had to pull the side panels at the front towards the middle of the car to remove the waviness in the fabric that is hanging down over the doors. (photo below) - Drive tacks (I use thumbtacks with large heads as they leave a smaller hole for this step) to ½ depth as necessary to achieve the best look and least amount of excess fabric. The focus now is on cutting out and seaming the panels. We cannot accurately do the edge reinforcing or the edge binding on the side panels yet, because we do not know precisely how wide the panel will actually be until after sewing the seams, so read all of the top making instructions below and then just be sure to have enough additional fabric when making the panels to be able to finish the edges. These panels will also be a couple of inches longer than the front and rear bows to facilitate stretching the fabric. This first photo (below left) shows the 3/16” welting and marks added using a tailors pencil. This seam and the outer door drip edge MUST be marked on the car. They are not a straight line when laid on the table due to the bows requiring more fabric. SEAM MARKING AND CUTTING To mark the seam, with the stayfast taut, press on both sides of the stayfast with the welting string underneath (above left). It will create a slight high point. Use the edge of a tailors pencil to make a rubbing of the line. Next, use a compass opened to 1 1/8” and scribe the cut line outside this seam line. Cut on the scribed line. Raise the stayfast edge up and transfer the locations of the hand stitch marks that hold the welting to the pads. These marks get the V cut outs for match marks (above middle). Chalk mark where the stitching should stop on each panel end. Tracing paper may be helpful. Remove the panel. ADD THE SEAM ALLOWANCE. We need 1/4” seam allowance. (could be 3/8” or more if doing a double top stitch or heavier fabrics). Use fabric (not carbon) tracing paper (shown above right). Place a scrap piece of stayfast under the tracing paper. Place the tracing paper chalk side up. Lay the panel seam area on the tracing paper. Use a wooden stick and pull it in a smooth parallel line 1/8” from the seam line on the outside side. This tracing line is your 1st stitch line guide. BACK CURTAIN SEAM A similar method is used for the back curtain seams. My rear curtain seams are at 46 ½” top and 43” wide at the bottom. Since there are no pads on the back curtain, stretch two temporary welting cords where you want the seam edges to be. I did also make a 4 mil poly template first so I knew roughly the size of stayfast needed. Mark the back panels as the top was done. Leave excess fabric to be trimmed later. (see photos below) SEAM JOINING Notice that both seam lines to be joined are not straight * (Upper left above). The curve of the side quarter panel is greater than the curve of the top panel. To hold these together easier while feeding the fabric into the sewing machine, it is best to put the fabric with the least amount of curve on the top side. This lets the fabric lay flat on the sewing machine base. Join these small V marks and seam lines on the work table. Work from the middle out. TRUST YOUR MARK, don't second guess and think they're wrong when laid on the table because the lines are not straight. Your line should be straight between bows only, it will usually slightly change direction at the bows. Not necessary but you can use ¼” basting tape just outside your seam line to temporarily hold the fabric together if you like. After the joining stitch this can be removed. Then fold over and top stitch this seam, always with the top stitch located toward the center of the car. *You cannot cut the top side panel edges with straight lines. Where they attach to main top panel, it will be straight lines mostly BETWEEN BOWS, but not all the way front to back. The sides will be a slight arc, NOT a straight line due to the bows making some fabric distances longer. Either fit the fabric to the car (that's what I do) or make a good pattern. Hugh 3 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now