Guest Ansis42 Posted December 8, 2014 Share Posted December 8, 2014 Hello all, I have a 1980 Buick LeSabre with a 4.9L 301 V8. I am working out the kinks after replacing both head gaskets. I am experiencing a very strange issue lately. I attempted to start it up one day. The engine cranked VERY slowly. But then out of nowhere, through some miracle, it started right up. I let it run for a while, and drove it around my neighborhood. I turned off the engine, then immediately tried starting it up again. Again, the engine cranked VERY slowly. This time, however, it never actually started. I figured the battery was dead or dying. I thought this was odd because this was a brand-new battery. So, I bought myself a multi-meter, and tested out the battery. It had almost a full charge at about 12.5. So, I thought that was weird. I figured I'd test for a short. The multi-meter indicated there was no draw at all at -0.00. So then, after proving that the battery was fine, I figured I'd try to start it up again. It cranked nearly perfectly (only a tiny-bit slow), and started right up. Let it run for a while, then turned off the engine. Again, I immediately tried starting it up again. Again, it cranked VERY slowly, and never actually started. So......starter?Any help would be greatly appreciated. Thank you. Link to comment Share on other sites More sharing options...
28 Chrysler Posted December 8, 2014 Share Posted December 8, 2014 Check the starter, solenoid, and all the connections.Check the battery's voltage drop while you are cranking the engine to see if the starter is drawing to much current. Link to comment Share on other sites More sharing options...
cahartley Posted December 8, 2014 Share Posted December 8, 2014 On a car that age I expect the starter bushings have had it........brushes too probably. Link to comment Share on other sites More sharing options...
bhambulldog Posted December 9, 2014 Share Posted December 9, 2014 On a car that age I expect the starter bushings have had it........brushes too probably.I agree.That could also cause the starter to overheat. Further causing the starter motor to run slower. A slow starter will also damage the brushes,The heat will also raise resistance in the wires, reducing the voltage reaching the starter. A vicious cycle Link to comment Share on other sites More sharing options...
vintagerodshop Posted December 9, 2014 Share Posted December 9, 2014 Remember always start with the basics. if the battery is a known good part look at battery connections and cables first. Corrosion and loose connections have caused a lot of spinning the Parts Wheel of Fortune. Link to comment Share on other sites More sharing options...
misterc9 Posted December 9, 2014 Share Posted December 9, 2014 Was the distributor removed or disturbed during this job? Timing could be advanced . This could cause slow cranking. You need to test voltage while cranking starter. Try jumpers from a running car. Was the battery ground strap disturbed where it bolts to the engine ? Might be a bad connection somewhere. Link to comment Share on other sites More sharing options...
Guest AlCapone Posted December 9, 2014 Share Posted December 9, 2014 (edited) My suggestion is to check the ground connection. Clean it or sand it shiny, I then on all my cars add. 00 welders ground cable. It worked for me and I had your problem several times. Wayne Edited December 11, 2014 by AlCapone (see edit history) Link to comment Share on other sites More sharing options...
plt341 Posted December 9, 2014 Share Posted December 9, 2014 my 1987 f-250 460cid cranked slow and would not start when hot.It had a broken connection on one of the field coils.Rebuilt starter replaced bad field coil problem solved.Never had a starting problem again. Link to comment Share on other sites More sharing options...
Hudsy Wudsy Posted December 11, 2014 Share Posted December 11, 2014 My suggestion is to check the ground connection. Clean it or sand it shiny, I then on all my cars add. 00 welders ground cable. It works for MPEG and I had your problem several times. WayneBy all means, start with Wayne's diagnosis first. I, too, have found that ground cables can "look" like they have clean connections, but simply don't! Also, because the starter is turning you might think that the connections are sufficient, but substantial current can be lost there, nevertheless. I also have run into this more than once. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now