stakeside Posted August 27, 2014 Share Posted August 27, 2014 This a Steward vacuum tank. Best I can determine model 93C. It is off my 1929 Dodge Bros 3/4 ton truck. The engine is a DA 6. What is missing here? The tank diameter is 4 3/4". Link to comment Share on other sites More sharing options...
keiser31 Posted August 27, 2014 Share Posted August 27, 2014 There are diagrams and answers here....http://www.allpar.com/fix/fuel/vacuum-tank-fuel-pump.html Link to comment Share on other sites More sharing options...
stakeside Posted August 27, 2014 Author Share Posted August 27, 2014 There are diagrams and answers here....http://www.allpar.com/fix/fuel/vacuum-tank-fuel-pump.htmlHelpful information but the cover assembly is quite different. I do have any provision for the hanging arm in the attached photo from the article. Still looking for some information on my tank.thanks for information. Link to comment Share on other sites More sharing options...
old car fan Posted August 27, 2014 Share Posted August 27, 2014 (edited) I do not think that's the right tank for any Dodge.The one you show in the pic, the 4 screw top is a constant suction model,the diagram is the 8 screw.I restore and rebuild tanks,nowhere in my book does it say Dodge used the constant suction?Also,just looked at a flyer from the Dodge club,no mention of the 4 screw.I can help you out,Before you put the electric fire starter on it.Ok,back on it.Conflicting info.The Dodge booklet shows them going to the Kinston tank in late 28,going to a Ac cam pump in 1930.My stewart warner book shows a vacuum tank in 30? Edited August 27, 2014 by old car fan (see edit history) Link to comment Share on other sites More sharing options...
stakeside Posted August 28, 2014 Author Share Posted August 28, 2014 I do not think that's the right tank for any Dodge.The one you show in the pic, the 4 screw top is a constant suction model,the diagram is the 8 screw.I restore and rebuild tanks,nowhere in my book does it say Dodge used the constant suction?Also,just looked at a flyer from the Dodge club,no mention of the 4 screw.I can help you out,Before you put the electric fire starter on it.Ok,back on it.Conflicting info.The Dodge booklet shows them going to the Kinston tank in late 28,going to a Ac cam pump in 1930.My stewart warner book shows a vacuum tank in 30?I doubt this was a not original equipment but it is possible. The tank was on the Dodge Bros truck went I bought it in 1970.It may be a tank for a Graham Bros truck since the 28 to 29 trucks were transitioning to Dodge Bros name. They were sharing parts. Link to comment Share on other sites More sharing options...
alfourfire Posted August 28, 2014 Share Posted August 28, 2014 That's the same model I have on my '29 Whippet. Looks all there. There should be an inner tank and a diaphragm on the bottom inside the outer tank. There is a guy online who repairs them but no parts for the 4 screw top. Link to comment Share on other sites More sharing options...
old car fan Posted August 28, 2014 Share Posted August 28, 2014 I have the parts,tanks,and rebuild kits for the 8 screw tops,also have parts for the 4 bolt stewert tankPm me if you woud like Link to comment Share on other sites More sharing options...
stakeside Posted August 29, 2014 Author Share Posted August 29, 2014 As you can see the float is no good. Are these available? Have the inner tank with the screen. I do not know what the diaphragm is that was mentioned in previous post. Is there any assemble publications or a listing to show vehicle usage of that model tank? Link to comment Share on other sites More sharing options...
nearchoclatetown Posted August 30, 2014 Share Posted August 30, 2014 I do not think any DB or GB used this type of vacuum tank. The DBC store carries a copy of the instruction manual for the correct SW vacuum tank, think it might be $8. Link to comment Share on other sites More sharing options...
stakeside Posted September 3, 2014 Author Share Posted September 3, 2014 I have the parts,tanks,and rebuild kits for the 8 screw tops,also have parts for the 4 bolt stewert tankPm me if you woud likeDo have the tank as shown in pic? Also is there a listing showing these Stewert tanks applications or vehicle usage ? Previous post stated it was on his Whipet. Link to comment Share on other sites More sharing options...
alfourfire Posted September 3, 2014 Share Posted September 3, 2014 If I recall correctly, there is a small rubber "flapper" at the bottom of the inner tank which acts as a check valve. That 's what I called a diaphragm. It's been a while. Link to comment Share on other sites More sharing options...
stakeside Posted November 24, 2014 Author Share Posted November 24, 2014 Still have questions. Will send more pictures of my vacuum tank. Link to comment Share on other sites More sharing options...
stakeside Posted November 24, 2014 Author Share Posted November 24, 2014 This tank assembly is quite simple. I believe I have all pieces: inner tank, float, and cover. The float is beyond repair. Cover has a vacuum shutoff valve that stops the vacuum went the float raises and tank is full.i will need a new float and Still looking for instructions for the model 93C vacuum tank.. Link to comment Share on other sites More sharing options...
alfourfire Posted November 27, 2014 Share Posted November 27, 2014 I have repaired the tank float twice. Submerged it in warm water to find the leaks, then soldered the leaks. I drilled a small hole in the bottom of the float to shake out all the gas and or water. Let it sit for a while to allow any fumes to evaporate then make the repair keeping the solder as thin as possible, then plug the drain hole you made. Make sure the hook from the float threads through both eyelets with the entire hook above both eyelets.(patience) so it operates smoothly. Link to comment Share on other sites More sharing options...
stakeside Posted November 28, 2014 Author Share Posted November 28, 2014 Alfourfire Thanks for information. My float will have to be replaced because it has cracks around the entire circumference. Does your tank have a model number.You were able to fix your tank. Are there replacements available Link to comment Share on other sites More sharing options...
stakeside Posted August 8, 2018 Author Share Posted August 8, 2018 On 11/23/2014 at 5:05 PM, stakeside said: This tank assembly is quite simple. I believe I have all pieces: inner tank, float, and cover. The float is beyond repair. Cover has a vacuum shutoff valve that stops the vacuum went the float raises and tank is full. i will need a new float and Still looking for instructions for the model 93C vacuum tank. . I am back checking on my vacuum tank rebuild parts. I need a new float and a rubber flap for bottom.. I may be able to fabricate a float if I had the right materials but prefer to purchase one. In previous posts there was many comments on if this is a correct application for this model of tank. Well it is what it is and I would like to use the tank in my truck. Link to comment Share on other sites More sharing options...
Friartuck Posted August 9, 2018 Share Posted August 9, 2018 http://www.classicpreservation.com/vactankfloats.html Link to comment Share on other sites More sharing options...
old car fan Posted August 15, 2018 Share Posted August 15, 2018 Do you still need parts. Link to comment Share on other sites More sharing options...
Hans1 Posted August 17, 2018 Share Posted August 17, 2018 please show a better photo for inner tank, bottom outlet. Mine has a pot metal elbow with a bakelite flapper , the flapper is at about 20 degree angle. The flapper needs to seal the bottom of the inner tank from the outer tank, to keep vacuum internal until inner float actuates upper valves. I had to use airplane dope ( it is gas proof ) to seal the pot metal elbow and to protect the sealing surface for the bakelite flapper. Your float is repairable, use rosin solder for electrical work. do not use acid core solder as it is corrosive. Be patient, could make hole in bottom to insert small tool ( nail ) to push dented sides back int shape. Then solder hole. Link to comment Share on other sites More sharing options...
stakeside Posted August 17, 2018 Author Share Posted August 17, 2018 Are there any information photos or manuals available for my 4 screw tank. I have the instructions for the 8 screw tank. Link to comment Share on other sites More sharing options...
stakeside Posted August 22, 2018 Author Share Posted August 22, 2018 On 11/23/2014 at 5:05 PM, stakeside said: This tank assembly is quite simple. I believe I have all pieces: inner tank, float, and cover. The float is beyond repair. Cover has a vacuum shutoff valve that stops the vacuum went the float raises and tank is full. i will need a new float and Still looking for instructions for the model 93C vacuum tank. These are the only parts and there functions for the Steward 93 C vacuum tank. Very simple system. The vacuum inlet has two eyelets for the float. I am not sure why there are 2 eyelets. Seams that would stop vacuum when tank is full. The flapper appears to be working and it would regulate the fuel flow. It appears that the only parts I need are: float, fuel inlet screen, and gasket. Are there any other parts I need? Link to comment Share on other sites More sharing options...
Hans1 Posted August 23, 2018 Share Posted August 23, 2018 (edited) My tank is quite similar. There is a small spring on the float arm. It is installed on float arm first, then arm is threaded into the two valve arms on cover. I think the spring is meant to provide a little pressure on the lower arm as float rises. The spring is very soft and measures about 1/4 inch in free length. ( un compressed ) /////////////////// In addition, I see no reason why a float of modern material could not be made and work. Your float will supply all needed dimensions. good luck Edited August 23, 2018 by Hans1 fat finger mistake (see edit history) Link to comment Share on other sites More sharing options...
stakeside Posted August 24, 2018 Author Share Posted August 24, 2018 Hans1 just checking if yours has a 4 screw top. Mine dose not have a float arm. Link to comment Share on other sites More sharing options...
Hans1 Posted August 24, 2018 Share Posted August 24, 2018 Yes mine are 4 screw tops. They also have an added feature of a double venturi ( vacuum booster to help with the windshield wiper ) This is just a separate piece which screws on to the vacuum inlet port. Hudson and Essex cars had this as part of original equipment. ///////////////// I have stayed away from the big float tanks for many years. Learned the lesson of difficulty looking for the springs, which always seem to be so fragile and break. Link to comment Share on other sites More sharing options...
stakeside Posted August 25, 2018 Author Share Posted August 25, 2018 Mine is a model 93 C or 930 Steward tank. I do not have the spring that attaches to the valve, not sure you mean by arms. Are they the eyelets at the valve? Are aware of any literature available for the 4 screw tank? Link to comment Share on other sites More sharing options...
Hans1 Posted August 25, 2018 Share Posted August 25, 2018 I did not mean to confuse with my use of the word arm. The float has a piece sticking up from it that threads into the holes ( loop ends ) of the valves mounted in the cover. I am in Michigan, You can call 517 2 six 3 three 6 six six if it is convenient. Leave message if I'm not immediately available. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now