Otahuhu

Original vintage period Oldsmobile script Motometer Has never used by myself been on shelf for years $US350.00 PLUS SHIPPING Contact beaconview8@xtra.co.nz

Left over Motometer parts Include thermometers Most parts not used and nos $US 120.00 plus shipping contact beaconview8@xtra.co.nz

Parts to repair Boyce Motometer I

Have a Delco Remy v16 distributor cap that gives the firing order as RH 3 7 4 1 6 2 5 8 LH 1 6 2 5 8 3 7 4 ALSO TERMINALS ARE MARKED AS TO WHICH SPARK PLUG IT FEEDS (IDIOT PROOF EVEN IN THOSE DAYS) MEASURE o dia of 5 1/8 inches Is it for a Cadillac or Marmon ? What are the worth good used condition or NOS Regards

Have a Delco Remy v16 distributor cap that gives the firing order as RH 3 7 4 1 6 2 5 8 LH 1 6 2 5 8 3 7 4 ALSO TERMINALS ARE MARKED AS TO WHICH SPARK PLUG IT FEEDS (IDIOT PROOF EVEN IN THOSE DAYS) MEASURE o dia of 5 1/8 inches Is it for a Cadillac or Marmon ? What are the worth good used condition or NOS Regards

From the shoulder to the end of the bulb is 7.5 inches (7 1/2) the thread is 11 1/2 AN 1.85 inches diameter The way this gauge is constructed it can be modified for any depth of tank by using collars on each rod to suit.

NOS 1929 Oldsmobile water pump kit $US 210.00 plus shipping Regards Len

For Sale shutter knobs and choke knob with bessels , one shutter knob needs one letter to fix $US 200.00 Both plus shipping Regards Len

NOS in tank fuel gauge for sale $US300 plus shipping Regards Len

A lot of commercial/ technical mumbo jumbo regarding Gemmer series 215 and for Franklins Gemmer 20500 The following company has made these for Franklins in the past and was a complete kit The company is Ricardo Cavallero S.R. L Bahia Blanca 1070 C1407ABT Buenos Aires Argentia Tel/fax 0054-11-46361547/46361507 E-MAIL chs@fibertel.com.ar Yes they are well aware that bearings are no longer available and have just completed to original spec steering box for a ferrari Have spoken to them and don't see a problem making 215 series Regards Len

Hi Thank you for info Gary was hoping to get away from making a jig What I need is for my NOS Stromberg UUR2 carburetor I intend to use, it needs a longer than standard throttle shaft Regards Len

What alloy material is a carburetor throttle shaft made from is it BRASS ,BRONZE OR ALUMINUM BRONZE or another form of alloy ? Where can one purchase a finished to size material to make a throttle rod from?

Looking for a suitable length Stromberg UUR 2 throttle shaft that will accommodate the hand throttle control lever at the opposite side of the accelerator mechanism. The UUR 2 throttle shafts offered for sale are to short for what I need Thanks Len

Another Reo Royale comes to the surface in New Zealand This time a 1931 Murray body right hand drive sedan. Is for sale For details contact Keripark@xtra.co.nz Advertised in Beaded wheels New Zealand vintage car magazine

Hello Stutz16 Can you post some photo,s of your assembly of the four speed conversion to your Stutz Thanks Len

Hi As a suggestion you can use a ball nose end mill to radius (5/16 dia?or to suit) the weld fillets Most can be done by mounting the item to a rotary table The fillet around the pipe section can be milled by using a dividing head Make sure you have the milling head on an angle to the work to see the end mill in contact with the fillet( not vertical to the work). Most ball end mill cutters are two fluted With Al the more flutes the better If you can only get two flutes take light cuts Regards Len

What is the dwell angle and rev setting speed for a twin ignition 1929 Stutz What is the correct tdc mark on the fly wheel Brian

have a look on e-bay as there are Auburn made thrust bearings for sale 3 inch OD by 2 inch bore Regards

What you have is a Borg and Berg 11Q These were used on a number of vehicles eg 1928 Stutz The bearing is a carbon one maybe a later had a roller Thrust Bearing eg 1929 Stutz There are clutch holders that with a bit of modification can be used The hinge pins if worn can be repaired(turned down) then pressing on the inner race of a needle bearing RegardsLen

Have a look on web site prewar cars under Oldsmobile parts Some early motors for sale suggest you contact person as he may have other motors Good Luck Len

Good you found an oil you like. Suggest you drop the diff out and have a look at the condition of the Worm Wheel you maybe in for a surprised as to what you find. Hope it does not have deep scuffed out marks across the matting face of the of the worm. GOOD LUCK Len

As a Stutz owner do not use any oil that contains Sulphur as it will eat the bronze wheel Oil used originally was camphor I use Penrite Transoil 140 that is designed for use in non ferrous bronze worm wheels In the past have stripped a number of Timken worm diffs to find wrong oil used with bronze wheel eaten away

HI I note the good machining you have carried out well done. I trust you have used an Aluminum Bronze in all of your yellow metal work, using brass or bronze will not end up with the end result you were looking when placed in use Regards

Sometime ago a Mr HWELLENS posted details on leaf spring settings If available could he post settings for 1920 to 1925 for Stutz cars of that period Thanks

If available could someone post leaf spring technical settings for both front and back leaf spring for 1920 to 1925 for the models of Stutz over that period Thanks Len