Dean3326

Members
  • Content Count

    24
  • Joined

  • Last visited

Community Reputation

0 Neutral

About Dean3326

  • Rank
    Member
  • Birthday 08/20/1952

Profile Information

  • Gender:
    Male
  • Location:
    Coplay Pa

Recent Profile Visitors

647 profile views
  1. What is the proper answer do you or do you not lubricate the pilot bushing before installing the transmission ??
  2. Dean3326

    1927 Gardner throw out bearing

    I need a throw out bearing for a 1927 Gardner model 8B imperial sedan with a Borg & Beck clutch. 1926 and1927 specs show they are the same size 3.0 OD 1.75 Id .62 thickness as described in the instruction manual it was made of a special Graphite composition. I understand the Auburn is very similar to the Gardner. Any help is appreciated. Thank you Dean
  3. Looking for a clutch release bearing It is item #10 on attached photos.Clutch model#64 type 10 OL Borg & Beck
  4. Dean3326

    1927 Gardner

    Need a left rear axle for 1927 Gardner 8BS42915 lycoming engine 4HM12298 Shaft is 32.25 long 6 splines length 2.31 OD 1.44 end thread 1.0 V200 cast into housing Columbia stamped on axle shaft Also need the left inner bearing Bock # 03520 and seals I understand Auburn Cord similar parts Call with any information 484-553-2042 Dean
  5. Dean3326

    1927 Gardner Imperial Sedan

    Need a left rear axle for 1927 Gardner 8BS42915 lycoming engine 4HM12298 Shaft is 32.25 long 6 splines length 2.31 OD 1.44 end thread 1.0 V200 cast into housing Columbia stamped on axle shaft Also need the left inner bearing Bock # 03520 and seals I understand Auburn Cord similar parts Call with any information 484-553-2042 Dean
  6. Dean3326

    Gardner

    1927 Gardner Imperial sedan I need a left rear axle . 6 spline
  7. Dean3326

    1925 11A gear shift

    I need to get the gear shift apart I do not have a key Can anyone give me some advice ? Could the roll pin in the side be drilled out to separate the pieces ?
  8. Dean3326

    Watson Stabilizer

    Looking for a source for the webbing in the stabilizers. Anyone have a source ?
  9. Dean3326

    1925 Franklin series 11A

    Looking for an engine for a 1925 series 11A
  10. Dean3326

    1925 11A Parts wanted

    Looking for the floor brace between toe boards and floor boards. R811 drawing # 33507 Toe board Bar Need the door glass regulator lift channel for a front door Windshield rubber seal mounted into the frame on the vehicle
  11. Dean3326

    1925 series 11A

    I'm looking for a source for the Door side and upper channels. What is an acceptable replacement for these channels. Also looking for the Window regulator rubber compression lip for all 6 door channels. need 1 window channel with the lip to attach the compression lip. This vehicle has frame sag,I have the Franklin prints to attach the steel cable and turn buckle to remove the sag,has anyone had any luck with this setup? Thank you
  12. Dean3326

    Upper Body Dimensions

    Hello. Restoring a 1969 Camaro Convertible I need the upper body dimensions. Does anyone have access to this information or know where I can get this information. I have tried the major collision dimension companies no luck. Hoping someone either has this info already or knows where I can turn to. Thank you
  13. Dean3326

    1926 Franklin spark plugs

    Spark plugs ? 1926 franklin model 11A engine E103545 can anyone tell me the type of spark plug that should be in this vehicle. It now has autolite 3095 with a reducer going from the 1/2 pipe thread of the spark plug to 3/4 pipe screwed into the head. Problem being the od of that reducer barely screws into the head maybe on 3 threads. so something is obviously wrong. What is the original spark plug and what is its thread dimensions. Also a source for technical information what should compression be? Thank you
  14. Dean3326

    Franklin

    !926 Franklin looking for sources of any technical information I can get. also what should compression be on the vehicle?
  15. Dean3326

    1926 Franklin

    Spark plugs ? 1926 franklin model 11A engine E103545 can anyone tell me the type of spark plug that should be in this vehicle. It now has autolite 3095 with a reducer going from the 1/2 pipe thread of the spark plug to 3/4 pipe screwed into the head. Problem being the od of that reducer barely screws into the head maybe on 3 threads. so something is obviously wrong. What is the original spark plug and what is its thread dimensions. Thank you