Aussi John 1
Members-
Posts
239 -
Joined
-
Last visited
Content Type
Forums
Gallery
Events
Everything posted by Aussi John 1
-
Shade blind bracket removal
Aussi John 1 replied to Aussi John 1's topic in Studebaker, Erskine & Rockne
Tinindian Mine just pushes on one end, but not the spring end. I need to remove them to have them plated. John -
1929 President FH steering box rebuild
Aussi John 1 replied to Gary_Ash's topic in Studebaker, Erskine & Rockne
Gary I think you will find that the 28 Ge uses a different box than the FH. I don't have a 28 parts book to check. I have 29 FD and two 29 FH's and the FH is defiantly different than the FD. The 29 parts book also list the Fcs and Fds different to each other. The GE is possibly the same as the FC. You need to get a box with the same casting number. Providing the holes line up the GE box may be useable, but the ratio and the angle may be different. It could even be better. -
Shade blind bracket removal
Aussi John 1 replied to Aussi John 1's topic in Studebaker, Erskine & Rockne
Yes the FH is the same, but what I want to know how to remove the bracket from the roll. -
1929 President FH steering box rebuild
Aussi John 1 replied to Gary_Ash's topic in Studebaker, Erskine & Rockne
Over 20 years ago I reconditioned the steering box on my Brooklands President. From memory, the pin was not removeable. I had the pin built up. The car has travelled in excess of 30,000 miles since. I recently checked it and it was still as good as new. It's a good idea to replace the bicycle head style ball bearings on the worm with Timken bearings. -
Can anyone tell me how to remove the end brackets from the spring side of the roll, on the blinds on the rear window and two side windows. on an FH President. I need to remove these to have them nickels plated. John
-
1929 President/ Commander Eight parts
Aussi John 1 replied to Aussi John 1's topic in Studebaker, Erskine & Rockne
No, unfortunately, I don't. -
29 FH President clutch bolts.
Aussi John 1 replied to Aussi John 1's topic in Studebaker, Erskine & Rockne
Thanks Rex. John. -
29 FH President clutch bolts.
Aussi John 1 replied to Aussi John 1's topic in Studebaker, Erskine & Rockne
Thanks Richard, but surely with all the Presidents in the ASC,, somebody must know the bolt specifications. -
dictator serial number plates
Aussi John 1 replied to automaschinewerks's topic in Studebaker, Erskine & Rockne
I had my 29 FH President down to the bare frame and there is definitely not a number stamped on the frame anywhere. Fortunately the aluminium plate was still intact on the frame, but very tatty as they usually are, so I bought a new plate. The plate on the right side of the frame which says President was not available , so I recently had one made. -
I need help with my 29 President Long clutch, can anyone give me the description of the three bolts that hold the two driven plates (Cutch plates) together, ( E2 11 on the illustration). I need to know the length, the diameter, the thread diameter, the thread length and whether it is a straight bolt, or a stepped bolt. Also do the three leaf springs ( E6) on the plate separator, face the fly wheel.
-
President rear engine mountings
Aussi John 1 replied to Aussi John 1's topic in Studebaker, Erskine & Rockne
Hi Rex Can you please check if you have any. Regards John Grant. -
Does anyone know if any one is making reproduction engine mountings. for 29-30, FH- FE Presidents.
-
President Windshield Frame Corners
Aussi John 1 replied to Aussi John 1's topic in Studebaker, Erskine & Rockne
Thanks. I should be able to make them. John -
Can anyone tell me where I can purchased the windshield frame corners that fit in the lower left and right side, of the windshield frame on 29-30 President sedans. I have emailed Steve Munts, 'Emailsrmunts@mindspring.com', but the email came back. Does anyone know his current email address.
-
Perhaps your handbrake cable is stretched.
-
Can anyone tell me the sizes of the rubber trunk seal an FH Victoria, I have included a photo of what's left of mine. also the cowl air vent seal.
-
Thanks for the confirmation, much appreciated. John
-
Thanks John Yes I have come to the conclusion, that it is not part of my President. John
-
Yes it is definitely an engine plate, but it's not for FH or FE Presidents. I think it's probably off a six cylinder Studebaker from the time Studebaker painted their engines green.
-
It is too thick for those applications, about 1/8" thick. It may not suppose to be painted.
-
This plate came with my 29 FH President. Does anyone know what it is and where it goes. I thought it fitted in behind the timing gears, but the bolt holes don't appear to line up. John
-
Frame/chassis identification.
Aussi John 1 replied to 54Coupe's topic in Studebaker, Erskine & Rockne
The 1925-6 Studebakers with the hydraulic brake option, had disc wheels, the frame has had wire wheels. I believe the hydraulic brake option was mechanical brakes with rods, boosted hydraulically. -
1929-31 President parts for sale 417-634-0660
Aussi John 1 replied to D P Dinsmore's topic in Studebaker, Erskine & Rockne
Can you please tell me the size of 20161 and how much you would want for a complete pair. -
1929-31 President parts for sale 417-634-0660
Aussi John 1 replied to D P Dinsmore's topic in Studebaker, Erskine & Rockne
Are these complete. Also how much do you want for them? -
1929-31 President parts for sale 417-634-0660
Aussi John 1 replied to D P Dinsmore's topic in Studebaker, Erskine & Rockne
I need a pair. unfortunately they are not a pair, either would have been OK if they were a matching pair.