Chuck Griffin Posted May 17, 2021 Share Posted May 17, 2021 Anyone know what size fuel line was used on a 40 Buick super? I need to replace the entire line from the tank to the fuel pump. I was thinking of using the steel braided ptfe line. Your thoughts? Link to comment Share on other sites More sharing options...
Bloo Posted May 17, 2021 Share Posted May 17, 2021 It was almost certainly 5/16" steel "Bundyflex" brake tubing, using double flare fittings. Cunifer might be a good substitute if you are concerned about rust. I wouldn't really recommend flexible line for the whole run, just a short piece of high quality flexible line to absorb engine vibration at the fuel pump end. I would probably use 30R9 rubber fuel injection hose there. If there is a hose at the tank end, I would do the same. While the tank is down, I would add a ground wire from one of the sending unit mounting screws over to the frame to prevent fuel gauge trouble. 3 Link to comment Share on other sites More sharing options...
Buick35 Posted May 17, 2021 Share Posted May 17, 2021 I've always just used copper tubing,it seems to work well and easy to bend. 1 Link to comment Share on other sites More sharing options...
buick looks fine for 39 Posted May 21, 2021 Share Posted May 21, 2021 An excellent product I've used in the past is a 5/16 fuel line stock produced by Thermoid. It comes in 25 foot rolls and has a rust resistant copper/nickel plating. It bends easily and once the line is bent into the desired shape the fuel line work hardens during the bending process. The only problem I had was a forming a tight bend near the gas line where it was double flared. It seemed that double flaring the end of the gas line work hardened the metal and I kinked the gas line when I tried to make a tight bend close to the double flare. Be careful attempting to make the gas line too pretty by eliminating seemly unnecessary sloppy bends in the line. The extra bends and length especially in the engine compartment allow the line to safely move when the engine is torqued under acceleration. Also an electric fuel pump is not a bad idea and it works best when it's placed close as possible to the gas tank. Be careful with copper tubing; over time it will work harden and form stress cracks which can be catastrophic. Thanks Leif 1 Link to comment Share on other sites More sharing options...
Buick35 Posted May 21, 2021 Share Posted May 21, 2021 Good to know,I've had the copper tubing on my Buick for about fourty years now and it's still good but I'll keep an eye on it.Thanks. 1 Link to comment Share on other sites More sharing options...
Bloo Posted May 21, 2021 Share Posted May 21, 2021 I have an teens car with it too. It was common in those early days. Not so much by 1940. It's fine until one day it isn't. Then it leaks or falls off. I can't imagine why anyone would use copper today when cunifer is available. Cunifer looks like copper, bends like copper, and does not work harden. Buick would have used Steel Bundyflex for the run to the front, but may have still used copper for the fuel pickup in the tank. Work hardening and cracking from vibration is a known property of copper. You can't fool mother nature. 2 Link to comment Share on other sites More sharing options...
Matt Harwood Posted May 21, 2021 Share Posted May 21, 2021 +1 for Cunifer. Incredibly easy to work with, done once and you never have to touch it again. Do not use flex hose for the entire fuel system. That's just hack work. 3 Link to comment Share on other sites More sharing options...
Ben Bruce aka First Born Posted May 21, 2021 Share Posted May 21, 2021 3 hours ago, Matt Harwood said: Do not use flex hose for the entire fuel system. That's just hack work. Some hacks are effective! 😁 Ben Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now