Guest Im4darush Posted September 6, 2014 Share Posted September 6, 2014 Guys, will I be ok running the ACR45s plugs in a 65 401 that has HEI? I wasn't sure if I should go down to the 43, and got the 45. I know I should increase the gap to .35-.40 with HEI.Standard Sunday drive usage, no racing. Link to comment Share on other sites More sharing options...
Guest Im4darush Posted September 6, 2014 Share Posted September 6, 2014 Car has champion RJ12YC plugs in it now. Link to comment Share on other sites More sharing options...
Seafoam65 Posted September 6, 2014 Share Posted September 6, 2014 Guys, will I be ok running the ACR45s plugs in a 65 401 that has HEI? I wasn't sure if I should go down to the 43, and got the 45. I know I should increase the gap to .35-.40 with HEI.Standard Sunday drive usage, no racing. 45 on the heat range is fine.....Keep in mind that the wider you gap the plugs, the more likely you are to burn a hole through theignition rotor or have spark leaking out of the plug wires. I'd leave the gap no more than .35. The big issue with HEI is the spark is so hotthe ignition components can't hold it in. Also make sure the tang on the ignition rotor is bent upwards enough to firmly ride on the carbontip in the middle of the top of the cap so there is no arcing taking place. My Dad bought a new 79 Camaro back in 1979 and right after it leftthe Chevy dealer with ten miles on it, spark was jumping out of the side of one of the wires to the block(It had the plugs gapped very wide at the factory) Link to comment Share on other sites More sharing options...
RivNut Posted September 6, 2014 Share Posted September 6, 2014 Tom Telesco doesn't contribute to this forum but he's very active on the Team Buick forum and the V8Buick forum. For quite some time now he's been advocating the use of Bosch platinum plugs. Take a look at the " 'Da Nailhead" forum on www.v8buick.com to see other recommendations. Ed Link to comment Share on other sites More sharing options...
Guest Im4darush Posted September 7, 2014 Share Posted September 7, 2014 Thanks guys. Do you think I am better off with the AC R45's, or the champions? I think the champions are the correct heat range but not 100%. They are listed as the plug to use for the application pretty much everywhere. When I took them out, they were gapped at .045 by the previous owner. I will say that the car had good quality MSD 8mm wires. Did not really look to see if there was any arcing going on prior to tearing it all down, but it ran pretty well and did not seem to have a miss.Im sure bosch is a great plug, but since this motor is all factory...im going to use a standard cheap plug. Just trying to decide if I should stick with the champions or go with the 45s considering I am running HEI. Link to comment Share on other sites More sharing options...
RivNut Posted September 7, 2014 Share Posted September 7, 2014 If factory is what you're after, then I'd go with the AC's. Then you'll need to go to http://www.lectriclimited.com/mainpage.htm and get the correctly dated plug wires - Lectric Limited part # 3330-641, the original wires had a hood on them that fit into the spark plug hole to keep dirt and moisture out. Battery cables, and T3 headlight bulbs. Then you'll need to get the tower clamps for the radiator hoses, and some Corbin clamps for the heater hoses. Probably not the last thing, but you would need a correct Declo group 27 top post battery. It's endless.The reason that Tom T. recommends Bosch plugs is that there's no need to worry about what kind of ignition system you have or worrying about gap if you run the pre-gapped platinum plugs.EdPS - if you use the correct spark plug wires, no one can see the spark plugs. Link to comment Share on other sites More sharing options...
Paul K. Posted September 7, 2014 Share Posted September 7, 2014 FWIW, I run NGK V-Power plugs in all my old cars. They stay cleaner longer. A real concern with carbureted engines and their richer air/fuel mixtures. Link to comment Share on other sites More sharing options...
RivNut Posted September 8, 2014 Share Posted September 8, 2014 Take a look at the plug wires on the engine in post #9 of this thread. You can see the proper date and the hood over the spark plug hole to which I made an earlier reference.http://forums.aaca.org/f177/silver-engine-color-1963-riviera-379068.html#post1338882Ed Link to comment Share on other sites More sharing options...
1965rivgs Posted September 8, 2014 Share Posted September 8, 2014 Thanks guys. Do you think I am better off with the AC R45's, or the champions? I think the champions are the correct heat range but not 100%. They are listed as the plug to use for the application pretty much everywhere. When I took them out, they were gapped at .045 by the previous owner. I will say that the car had good quality MSD 8mm wires. Did not really look to see if there was any arcing going on prior to tearing it all down, but it ran pretty well and did not seem to have a miss.Im sure bosch is a great plug, but since this motor is all factory...im going to use a standard cheap plug. Just trying to decide if I should stick with the champions or go with the 45s considering I am running HEI.I personally dont like Champion spark plugs. Once they fuel foul they are never the same. If you cant get the right heat range in AC Delco (BTW I think you will be OK with the 45`s for cruising) check Motocraft. They make a good plug and should be inexpensive. Of course, the NGK platinums is apples to oranges...but personally I think it pays dividends to use the highest quality spark plugs that are available...just my 2 cents, Tom Mooney Link to comment Share on other sites More sharing options...
Guest Im4darush Posted September 8, 2014 Share Posted September 8, 2014 Take a look at the plug wires on the engine in post #9 of this thread. You can see the proper date and the hood over the spark plug hole to which I made an earlier reference.http://forums.aaca.org/f177/silver-engine-color-1963-riviera-379068.html#post1338882EdI see what you are talking about Ed. If I ever put my original points distriibutor back in the car, I will have to get a set! Link to comment Share on other sites More sharing options...
DAVES89 Posted September 8, 2014 Share Posted September 8, 2014 Can you see into the future Ed? What's funny is you were post 8 talking about post 9...Take a look at the plug wires on the engine in post #9 of this thread. You can see the proper date and the hood over the spark plug hole to which I made an earlier reference.http://forums.aaca.org/f177/silver-engine-color-1963-riviera-379068.html#post1338882Ed Link to comment Share on other sites More sharing options...
RivNut Posted September 8, 2014 Share Posted September 8, 2014 (edited) I resemble that remarkEdPS - Dave, I'm referring to post 9 in the linked thread, not this one. Edited September 8, 2014 by RivNut (see edit history) Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now