Buzz68

My Metz I sold earlier this year I found metric sized sealed ball bearings that was a close fit Shim pressed fit in the hubs Made spacers on the axle bolts Luckly on my 12 6 of the 8 bearings was the same Larger inner rear balls I found metric sized balls that took up the wear

Late 14 engine FS running engine added a starter recently Cast date on block 11-7-14 Cast date on low head 11-7 Narrow 3 rivet pan Magneto good to run on and can send video of it running All babbitt good with shims good cam and bearing there as well Unsure of the bore size but from the bottom looks good Trans is redone but I drums are scored Stock ford clutch Dime sized hole pressure plate Rebiuldable aluminum hogs head Been open so I go though it Asking $1900 obo located Sparks Nv Bob Jalopyt@yahoo.com

Hard dirty work is all but done finish it your way need room Everything new or rebiult and can't biuld one to this stage with a clear title to boot Inquire at Jalopyt@yahoo.com Located sparks Nv Asking 8500 obo

I agree Stutzman is great but my last two wheels cam from wood by Kevin in Washington he claims he can use several kinds of woods and finish one are great fingers joints are tight $130 to my door can't beat that

Hope this helps On my 1912 Metz yes not same but same issue I measured the hub and spindle and actually found a metric ball bearing that is sealed no issues so far Had to make a spacer fill in distance for the old seal I get the timken # if the helps let me know

Kevin's wheels in Washington Noah Stutzman There's more last two cost me 125+ shipping

I have tried it roll cars around But never had tube or air in it that would truly be scary So I vote NO I have since learned use rope wrap the rim

Yes Grey area in most states But it's not a stock factory item But motocycle regs allow aqurylic plex and other clear plastics as a wind breaker Going with aqurylic for the time being has higher rating on safety then safety glass

Hi all thanks in advance for advice what's best to use laminated glass Or aquirlic or plex or ?????

Besides safety laminated glass what other choices do you have

Anyone making ingredients repops still Looking for a brass one but would settle for aluminum one

Deal pending

Was giving it some thought part with my metz to many prodjects and room and hard to find time. I was told when I bought it and title says it's a 12 but thinking it's more 13-14. Older restoration and currently wheels and magneto being rebiult so pickup where n I left off Send a note if your interested

Steel

What a prodject I was considering it off and on but the trans be a be stumbling block why I just could not pull the trigger Mark honest guy but can't wait see the finish line

New ask offer Can be used either mag or bat coil sell new at $400 This never been mounted asking 300 Will listen offers

See pic and make me an offer

See pic and make me an offer

Gotten it to spark but I would say needs a rebiuld point and everything are clean good threads spins no signs of wear Asking $175 obo will fit flat rate box $20

Looking for a set of burner bases and elbows for gas lamps CM #75 lamp just wanted see if there's any availible befor I make a set thanks Have burners Thanks in advance

Well only going by the title I'm in no way an expert S/n on my engine is unreadable So looking at 13 restored by the famous Bill Harrah collection (there's is a 13 )who was well noted for authentic correct restoration my car matches there Wheels and shift lever only different I found so far is the cylender head all lights and the oil filler on the motor So mine might be a 12 by DMV clerk but it's been that way since there's where my paper trail starts

My 22 parts book shows this same wheel and my 12 has the same wheel as Mr Harper's car but then I think alot can happen in 100+ years

Mirror tgat convex in the light I have found a lamp that's been robbed of everything else but the mirror Will need make mounting blocks Wedges as the lamp very different but mirror measures correctly

Gotten some great help here so Here goes need one concave 6" headlight mirror or idea for a replacement I've seen the replacement mirrors made by Gilbert but though I see what ideas I get here first Thanks