Turbo Kane

I have a NOS Mopar AIC still in box. I'd sell it to you for $45 shipped. Pm if interested

Congratulations! I bet you had a blast! Just out of curiosity what do you have for suspension? I have Sachs touring shocks/struts with suspension techniques 1" lowering springs for a daytona. Car seems to handle great and comfortable with much less body roll. You can pm me with info to not get off topic on your post. Congratulations again! Car looks awesome in those turns!

I had overheating problems running one of those in my Omni. Was bad on a 75-80deg day doing 65 on the freeway. City cruising would be fine. Look into a vw scirocco radiator I've seen more ppl successfully running those. Looks good though!

2 more pictures of 202441. Photo credit to Marybeth Kiczenski

I know! We missed the fireworks and nitrous rental car this year.

The speaker covers I switched, hated the fuzzy ones. All original parts will be kept with the car. It has single pivot K frame or "early". It's non common block and from my understanding the wood grain interior parts are the only unusual factory add on with the car. Might be a late early when they started introducing the wood grain. Thoughts?

202441, I believe it has yet to be added to the registry. Put 1000 miles on it this trip. The furthest I've taken it. Rolled 30,000 miles. It was smooth and comfortable without a problem! Noticed one tiny little rock chip on a headlight. Little bummed about that. Had to drive through lots of hwy construction on 80 coming into Illinois. Might use a windshield repair kit to fill it in.

I'm sure there will be more to come. Pretty rare to have a Tc Masi next to a Phantom R/T!

Replace the baro read solenoid on the same bracket the map sensor is attached to. It is probably stuck and not allowing the map to get a proper reading

Strut tower caps sold to Mac48. The headlight covers and rad/int shroud are available.

I'd be willing to separate $25 for strut tower caps $25 for headlight covers $50 for radiator/intercooler shroud

Center bumper to radiator/ intercooler shroud is 90-91 specific. headlight covers and strut tower caps. $100 for everything plus shipping

Degerb- My best advise it to put that gob of silicone directly in the center. Close to golf ball size. When you start pressing the two together you'll have some air bubbles and you just keep pressing around and around. If you get a good grip on it moving the glass in a circular motion helps. Just have to be very patient. You'll get it all worked out. The liquid nails silicone may seem hard to get off the paint when it dries. I used some diluted mineral spirits to get it off with ease then hand wax/polish and your good to go. Don't forget to tap the glass in place while it dries over night.

Royal Cabernet/Ginger/Tan top/16V

That is the dirty factory sealant that ls in between the two pieces of glass. I used acetone on the gold decal attached to the inside glass to remove the rest of the corrosion. The laminate is on the outer glass and the sealant should easily peel off of it by hand. Maybe use slight heat if it's not coming easy.

I used my wife's hair drier just don't tell her that ?! I think a heat gun would be fine at a distance maybe 6" away and try to keep from getting to close to the edges. Might damage the paint otherwise. Google search nylon trim pry bar I'm sure those would work geat. Honestly I used a flat blade screwdriver with pretty light pressure. Left a minor amout of paint damage however I'm painting the top for it didn't matter for me. Might be wise to use painters tape around the outside of the glass or atleast between the pry tool and the paint. Good luck! Be very patient with it and whatever you do don't drop it when it comes off. I think I put something on the ground below in case it popped off and I couldn't catch it.

Another note, put a large amount of sealant directly in the center and then push out all the air pockets to to edges. Don't forget to tape it in place atleast over night until the sealant sets.

The bottom picture I used permatex "clear" window sealant and as you can see it's not clear it's foggy. The liquid nails clear seal works great and it's very clear. Good luck and take your time

^ Rock auto carries new molded upper hoses for 8v sohc. They didn't remake this hose in rubber. TU might still have a remake silicone version for $100. You won't find a new OE replacement anywhere. Just for the bump I'll lower the price to $50 shipped. This is a very nice takeoff hose from a 30k car. Someone who what's to keep a car all original and needs one message me. We'll work out a deal! Thanks!

Very nice condition used upper radiator hose for 89 16v only. $55 shipped anywhere I take PayPal