gregchrysler
Members-
Posts
306 -
Joined
-
Last visited
Content Type
Forums
Gallery
Events
Everything posted by gregchrysler
-
Trying to figure what went wrong when engine just stops
gregchrysler replied to StylishOne's topic in Technical
use jumper cables from battery to starter --negative on casing of starter positive to starter bolt should turn starter-- bang starter with hammer solenoid may be stuck -
6 volt generator charging system in question
gregchrysler replied to Summershandy's topic in Technical
check ignition wiring also when positive battery cable hits starter post with positive it should turn starter -
6 volt generator charging system in question
gregchrysler replied to Summershandy's topic in Technical
leave original starter wires on and add jumper cables -
6 volt generator charging system in question
gregchrysler replied to Summershandy's topic in Technical
run a jumper cable to the positive side of the starter and the other cable to either the negative battery side or a good ground then u will know if it s the wiring -
6 volt generator charging system in question
gregchrysler replied to Summershandy's topic in Technical
check voltage regulator and cca on battery they go bad after 3 years and check grounds and wire gauges and connections on starter -
1949 chrysler royal woodie for sale CHEAP
gregchrysler replied to gregchrysler's topic in Automobiles and Parts - Buy/Sell
very rare only 4-5 left out of 850 produced --new interior -rebuilt motor and trans needs linkage adjustment -
How about a rare one owner 1949 Chrysler Royal Woodie? Asking $39,000 ==2 were for sale on e bay one $160,000 and one $95,000 only 4 or 5 left out of 850 made call me greg natale 401-487-5168
-
sprag --can a bad sprag cause no reverse??? chrysler
gregchrysler replied to gregchrysler's topic in Technical
Thank s spinney 1949 Chrysler royal Woodie 6 cyl fluidmatic - sprag clutch has spring and roller? used for reverse? I think it is a m6 tranny thanks again need diagrams and diagnostics -
align input shaft from tranny to clutch and engine
gregchrysler replied to gregchrysler's topic in Technical
thanks everybody got it back in still no reverse sprag????? -
1949 chrysler royal woodie
gregchrysler replied to gregchrysler's topic in Automobiles and Parts - Buy/Sell
all doors open and close perfectly - I m not trying to get top dollar There is a lot of room money wise to perfect the car -
1949 chrysler royal woodie
gregchrysler replied to gregchrysler's topic in Automobiles and Parts - Buy/Sell
wood is still being done -
I had the same problem Brought the starter back 5 times and finally he discovered that the alignment of the bolts on the starter (positive and negative) 2 bolts on the bottom of the starter were not aligned internally in the starter-- instead of being 180 degrees transverse internally they were not making contact fully enough to start the gear push to the flywheel So align bolts internally and externally I tried everything also
-
1949 chrysler royal woodie
gregchrysler replied to gregchrysler's topic in Automobiles and Parts - Buy/Sell
keiser there is one for sale $95,000 on e bay I am asking 1/2 of that another one for $160,000 on e bay This could be an investment it wont take too much work to finish but I need to sell it I know it is not perfect but the price is mechanics are almost done Thanks for you help anyways. wood is being sanded that was urethaned -
1949 chrysler royal woodie
gregchrysler replied to gregchrysler's topic in Automobiles and Parts - Buy/Sell
Matt everyone can't have concurs cars like you I am redoing the wood to pure white ash tranny is being gone thru It's not perfect but maybe someone could finish it up and make a lot of money and then maybe they could afford to buy one of your concurs cars at pebble beach -
Greetings friend==can a bad sprag cause no reverse? I have a 1949 Chrysler Royal Woodie 251 ci fluidmartic m6 transmission first and high gear work fine