RivNut Posted May 24 Share Posted May 24 (edited) I had my '64 in a restoration shop for a while a couple of years ago. Unbeknownst to me at the time someone removed the rear 1/4 windows and channels, both left and right. After what seems like about a hundred hours of trying they won't go back in. Had I have known what their intentions were, I would have said "DO NOT remove them !" but sadly I cannot turn back the clock. Does anyone out there know of the trick to getting the two rollers lined up with the two channels when nothing can be fastened down. Lots of videos on YouTube but they all end before the task has been completed. I have a feeling the guys posting the videoes ran into the same problem and gave up. Any suggestion would be helpful. Oh yeah. For those of you who would suggest "look on the chassis and/or body manuals" — we have and they don't explain squat (not my first choice of words.) Ed Edited May 24 by RivNut (see edit history) Link to comment Share on other sites More sharing options...
Dundee Posted May 24 Share Posted May 24 (edited) Ed Many feel your pain….its been 2 years since I had those babies out and I don’t have the car here to even look at it. All I have is some cryptic notes in my book so I will hit you with them and cross my fingers something gels! Access panel off! Motor and arm in first Guide in next and position upper adjustment bolts to forward and bottom of slots. Put glass in back first push door guide away outward. Slot rollers and glass into track and push top adjustment up and back and allow glass down to lower stop. Fit lower window cam over arm roller and screw with curve facing forward. Fit rear cam to rear window roller. Then the adjustments start😵💫 God luck!!! PS without this guide removed I could never get the glass in or out! Edited May 24 by Dundee (see edit history) Link to comment Share on other sites More sharing options...
tenugent Posted May 24 Share Posted May 24 The main problem is getting the front two front wheels in the double channel at the same time. Link to comment Share on other sites More sharing options...
RivNut Posted May 24 Author Share Posted May 24 2 hours ago, Dundee said: Ed Many feel your pain….its been 2 years since I had those babies out and I don’t have the car here to even look at it. All I have is some cryptic notes in my book so I will hit you with them and cross my fingers something gels! Access panel off! Motor and arm in first Guide in next and position upper adjustment bolts to forward and bottom of slots. Put glass in back first push door guide away outward. Slot rollers and glass into track and push top adjustment up and back and allow glass down to lower stop. Fit lower window cam over arm roller and screw with curve facing forward. Fit rear cam to rear window roller. Then the adjustments start😵💫 God luck!!! PS without this guide removed I could never get the glass in or out! It all sounds good on paper but we've gone through every possible scenario. Watched a couple of YouTube videos that do everything but finish the task. I'm thinking it's time to give up on this DIY $#%* and call in a professional. Link to comment Share on other sites More sharing options...
gungeey Posted May 24 Share Posted May 24 Comprehensive instructions are available in the Buick Body Service Manual. Wear gloves, lots of sharp sheet metal 2 Link to comment Share on other sites More sharing options...
RivNut Posted May 24 Author Share Posted May 24 If you’ve done this and used this illustration as a guide, you would know that the four marked “window regulator mounting screws” are drawn in incorrectly. If you’ll point out where it gives detailed instructions for installation, I would really appreciate it. As far as gloves are concerned, they’re too bulky to get your hands inside the cavity. Rubber gloves are worthless. You cannot see inside the cavity, it all is done by feel. Also, gloves are worthless when it comes to feel. I have a feeling that women with their smaller hands worked on this part of the assembly line. Link to comment Share on other sites More sharing options...
gungeey Posted May 24 Share Posted May 24 I actually never had your issues, done it a number of times probably without the aid of the book. Just winged it. I think you're flummoxed and making too big a deal of it. Sounds like you are getting really frustrated. Walk away before something gets broken or you get hurt. If you don't give up on it completely and decide to try again wear cotton gloves. Link to comment Share on other sites More sharing options...
Dundee Posted May 24 Share Posted May 24 Rubberised cotton gloves by the ten pack for cars. The job is possible don’t forget the video on the second one when you get it figured out your own way 🤪 2 Link to comment Share on other sites More sharing options...
powerage Posted May 25 Share Posted May 25 I achieved this task but may have blocked out traumatic memories of it. All I recall is a lot of time and colorful language Link to comment Share on other sites More sharing options...
Wayne R Posted May 25 Share Posted May 25 (edited) Ed , Yes you are correct skinny thin hands and arms make a differents. A small thing you may not have tried or realize, because both windows are in pairs, alot of times it helps by picking the easy est side to do first, because if you are right handed the passenger side might be easy er,---then do the drivers side second,--and get used to using left hand as well fitting some difficult screws on an angle.---dont give up you will get them done. Edited May 25 by Wayne R spelling (see edit history) 1 Link to comment Share on other sites More sharing options...
rivolution Posted May 25 Share Posted May 25 I did this just last year, to replace my plastic guides and clean the channels. I remember it took a lot of jiggling and fussing, required having the nuts on the two upper guide studs entirely removed so the whole assembly had a lot of play, and even then I think I ended up applying some force at some point and thinking, "this is probably a bad idea". But I got it in there. I also remember thinking, "How in the world did they mass produce these cars??" and wondering if the guys on the assembly line had some efficient way of doing it that was totally escaping me. 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now