Summershandy Posted March 1, 2018 Share Posted March 1, 2018 Part of my brake system replacement I'm also cleaning things up. Instead of paying $$$ for sandblasting and powder coating, I'm just wire wheeling with some elbow grease. This is not a show car. I had an old can of grey rust killer and did the back side of the brake plate (for a poor choice of words). I like the flat colour. My question is, should I also paint the other side where the shoes are? I know absolutely nobody will see it but will it start rusting again or am I asking for problems like paint chipping and getting on the shoes/drums? I did get it down to bare metal. Thanks! Link to comment Share on other sites More sharing options...
Rusty_OToole Posted March 1, 2018 Share Posted March 1, 2018 Definitely paint it. It will do no harm and will do some good by keeping off rust. Many parts under the car were not painted when the car was new because the factory did not want to waste the money and they figured the car would be junked in a few years. To keep an old car good you need to paint and preserve things. Link to comment Share on other sites More sharing options...
joe_padavano Posted March 1, 2018 Share Posted March 1, 2018 The backing plates from my 67 Delta 88 looked about the same once I cleaned them with oven cleaner. No rust at all thanks to years of caked oil and grease. I painted mine in and out with "rust paint" (I used the paint from TP Tools, but POR, etc are all the same). I left bare spots where the edges of the shoes ride on the backing plate, but otherwise painted the entire backing plate. Link to comment Share on other sites More sharing options...
Summershandy Posted March 1, 2018 Author Share Posted March 1, 2018 Awesome guys thanks for the input! Good call Joe, those "bare" spots under the shoes are lubricating points. Besides, I want to blow the mechanic away when it comes to inspection time to make it roadworthy! Link to comment Share on other sites More sharing options...
keiser31 Posted March 1, 2018 Share Posted March 1, 2018 (edited) I would go with John Deere Blitz Black for all chassis paint and inside the backing plates. Edited March 1, 2018 by keiser31 (see edit history) Link to comment Share on other sites More sharing options...
Rusty_OToole Posted March 1, 2018 Share Posted March 1, 2018 I paint the whole plate and put a dab of white lithium grease where the shoe sits. Link to comment Share on other sites More sharing options...
joe_padavano Posted March 1, 2018 Share Posted March 1, 2018 21 minutes ago, Rusty_OToole said: I paint the whole plate and put a dab of white lithium grease where the shoe sits. I always apply a dab of grease also, but I figured the paint would be worn away in short order, so why generate paint dust and chips that might contaminate the brake shoes? Link to comment Share on other sites More sharing options...
Bloo Posted March 1, 2018 Share Posted March 1, 2018 I do that too but I use Sil-Glide. Grease can contaminate the shoes if you ever get the brakes hot enough to melt it. Sil-Glide needs much more heat to melt. Mask the pads if paint chips are a concern or problem. I never got concerned because my rattle-can paint was so thin. Link to comment Share on other sites More sharing options...
Rusty_OToole Posted March 2, 2018 Share Posted March 2, 2018 I can't be bothered to mask off the tiny spots where the shoe rubs. Have never had a problem. Some backing plates come painted from the factory, they aren't masked either. 2 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now