Guest Downtimesfl Posted January 7, 2015 Share Posted January 7, 2015 Hey Fella's So 1st of many questions. So The guy I bought the car from replaced the forward wall of the truck, or the fire brake between the cabin and the truck with a sheet of 1/4 PT plywood. I'm thinking this is not a great fire brake, and while it is easy to screw into, and I'm sure could make a nice table top somewhere, I think wood really only gets to be in the Chevies, not my poor buick. Can i get any pics of what it is supposed to look like so i can recreate it? Or if you have a line on an origional one that isn't roached to all get out that is repairable.Thanks in advance! Link to comment Share on other sites More sharing options...
39BuickEight Posted January 7, 2015 Share Posted January 7, 2015 Here are a few of mine, assuming the coupe looks like the sedan??? Not much better than plywood lol. Also, if you check out my restoration thread, there are photos of most every part of the car. Link to comment Share on other sites More sharing options...
Barney Eaton Posted January 7, 2015 Share Posted January 7, 2015 I cannot say what is correct for your '39 but many cars both entry level and high end had the metal braces covered with cardboard (mounted on the passanger side) there was not much concern about a "firewall". If you install sheet metal, you could get some noise/vibration from its movement. With all the building products available today you have many choices. My '39 trunk had some of the original cardboard down the sides. I replaced all the pieces with thin Masonite covered with carpet (late model trunk style carpet in grey) While not original it looks good and is not as extreme as a custom upholstered trunk. The one thing I have not attacked is the underside of the deck lid..... it is crying for attention. Link to comment Share on other sites More sharing options...
39BuickEight Posted January 7, 2015 Share Posted January 7, 2015 Barney is correct as usual-he is a guy to listen to for sure. I was just showing the metal structure. Link to comment Share on other sites More sharing options...
Guest Downtimesfl Posted January 7, 2015 Share Posted January 7, 2015 okay thanks fella's, I don't even have the braces much less anything else left. my truck floor does look identical though. Link to comment Share on other sites More sharing options...
Terry Stock Posted January 7, 2015 Share Posted January 7, 2015 Ours has cardboard screwed on the trunk side. I'd say it's original. Link to comment Share on other sites More sharing options...
jvelde Posted January 9, 2015 Share Posted January 9, 2015 My '39 Business Coupe has the original plywood between the trunk and the interior of the car. Link to comment Share on other sites More sharing options...
Guest Downtimesfl Posted January 9, 2015 Share Posted January 9, 2015 yeah auto correct on a phone is a bit brutal with forums sometimes... Link to comment Share on other sites More sharing options...
Matt Harwood Posted January 9, 2015 Share Posted January 9, 2015 My '41 Century had a sheet of 3/4 inch plywood from the factory. 1/4 inch is too thin, but some kind of plywood is indeed correct. I don't think it was there as a fire break, but rather to simply separate the two compartments cheaply and with better sound damping characteristics than sheetmetal. Link to comment Share on other sites More sharing options...
39BuickEight Posted January 9, 2015 Share Posted January 9, 2015 My '41 Century had a sheet of 3/4 inch plywood from the factory. 1/4 inch is too thin, but some kind of plywood is indeed correct. I don't think it was there as a fire break, but rather to simply separate the two compartments cheaply and with better sound damping characteristics than sheetmetal.Matt do you know if this would also apply to sedans. I would think so? Link to comment Share on other sites More sharing options...
Bob H Posted January 9, 2015 Share Posted January 9, 2015 Matt do you know if this would also apply to sedans. I would think so?Billy:Neither of my 1939 Special parts sedans had a plywood bulkhead behind the rear seat. The seat back hooks directly to the sheet metal structure. There was a thin "trim panel" installed on the trunk side of the seat back support structure. My 46S coupe and 46C convertible have or had a 3/4 inch plywood bulkhead with sheet metal clips that the rear seat back attaches to. I have a badly deteriorated but intact bulkhead from the 46S that will serve as a pattern.Bob H Link to comment Share on other sites More sharing options...
39BuickEight Posted January 9, 2015 Share Posted January 9, 2015 (edited) Billy:Neither of my 1939 Special parts sedans had a plywood bulkhead behind the rear seat. The seat back hooks directly to the sheet metal structure. There was a thin "trim panel" installed on the trunk side of the seat back support structure. My 46S coupe and 46C convertible have or had a 3/4 inch plywood bulkhead with sheet metal clips that the rear seat back attaches to. I have a badly deteriorated but intact bulkhead from the 46S that will serve as a pattern.Bob HThanks Bob, neither of mine had any wood either, but it would make sense that something would be there. Maybe not. Edited January 10, 2015 by MrEarl chngd truck to trunk (see edit history) Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now