dhaven64 Posted November 23, 2014 Share Posted November 23, 2014 Hey folks. I received a nice new package tray for my 64 Riviera from Clark's. Any suggestions on how to secure it? Didn't come with any hardware and there are no holes on the tray for mounting it. Thanks in advance! Link to comment Share on other sites More sharing options...
68RIVGS Posted November 23, 2014 Share Posted November 23, 2014 (edited) I think maybe it's held in by 'gravity' ???Usually the rear window lower moulding, rear seat and sail panel secure them in place, at least that's how it is on my '68, in addition to some special friction, screw type fastners in the plastic package tray. A '64 Fisher Body Manual should provide the correct information about securing the '64 package tray. Edited November 23, 2014 by 68RIVGS (see edit history) Link to comment Share on other sites More sharing options...
dhaven64 Posted November 23, 2014 Author Share Posted November 23, 2014 Thanks Randy. The manual specifies screws (which I have) but the new tray has no holes. I just don't wanna drill holes in the tray because it looks so nice without them, but it won't lay flat and flush unless I secure it with the screws. Ugh Link to comment Share on other sites More sharing options...
RivNut Posted November 23, 2014 Share Posted November 23, 2014 How about some velcro? Put one side on the back of the tray and the other side on the tabs that the screws go into. That's how GM held the headliner up in my '85 coupe. Link to comment Share on other sites More sharing options...
dhaven64 Posted November 23, 2014 Author Share Posted November 23, 2014 Great idea! I'm gonna give that a try and some weatherstripping glue glue. Thanks! Link to comment Share on other sites More sharing options...
RivNut Posted November 23, 2014 Share Posted November 23, 2014 Think about what glue will be like if you have to take the tray out again. Link to comment Share on other sites More sharing options...
dhaven64 Posted November 23, 2014 Author Share Posted November 23, 2014 True true. Link to comment Share on other sites More sharing options...
JanZverina Posted November 24, 2014 Share Posted November 24, 2014 http://forums.aaca.org/f177/package-tray-work-my-63-a-372855.htmlHi dhaven,Here's a thread from a little bit ago when I redid my parcel shelf on my '63. Should be very similar if not exact to the '64 regarding removal and installation, unless your new one is one of those fiberglas shelves. Others can chime in, but IIRC those need some fettling and fitting. My board was in great shape so all I did was remove it, recover it, and reinstall. The rear seats and some window moldings must come out to do the job. Link to comment Share on other sites More sharing options...
dhaven64 Posted November 24, 2014 Author Share Posted November 24, 2014 Thanks Jan. Yes, my shelf is fiberglass and I've already removed the old one. I'll take a look at that thread and see if I can come away with some pearls. Link to comment Share on other sites More sharing options...
JanZverina Posted November 24, 2014 Share Posted November 24, 2014 Hi dhaven, You may want to have other members weigh in on their experiences in fitting a fiberglas one. You'll most likely get some good tips on what/what not to do. Cheers/ Link to comment Share on other sites More sharing options...
68RIVGS Posted November 24, 2014 Share Posted November 24, 2014 I like Ed's velcro approach - makes for relatively easy future removal (...if need be), for fitting, farting 'n fiddling. LOLCertain types of glue, or spray adhesives might be OK, but they are usually permanent. Construction adhesive like Lepages PL Premium, a 100% polyurethane would also fall into that catagory If you are selling the car, and don't plan on removing it again, glue or a spray adhesive would do the job without any screws ! Link to comment Share on other sites More sharing options...
slosteve Posted November 27, 2014 Share Posted November 27, 2014 I am just getting around to installing the one I purchased awhile back from Clarks. I DON'T want to drill any holes in the wrong place so what I've done is drilled the 2 holes furthest to the rear and outside that the trim plates/moldings fit on top of. Mine (a '65) were 50 & 1/2 inches apart and I used those moldings to help determine their height after first fitting them on my old, distorted cardboard tray. I came out good with those holes so I installed masking tape above the center hole of the three remaining to make markings on, marked a straight line vertically up onto the glass area from the hole and then put the new piece in place securing it with the 2 end screws. I determined the center hole should be 1 1/2 inch below the rear lip of the tray. If that makes absolutely no sense to you, I could take some photos and post them when I get back to it.SteveSteve Link to comment Share on other sites More sharing options...
alini Posted November 27, 2014 Share Posted November 27, 2014 Install the screws in the holes in the body, with the package tray removed. Put the package tray where you want it and the screw heads can scratch the underside and you can see where the holes need to be. You may need to back the screws up a little at a time until they touch. You could even put some vaseline or a dab of silicone on the screw head which will mark the back side of the package tray. Once you drill the hole use a small size like 1/16. place the tray back in place and stick a piece of wire/clothes hangar through the hole to see how lose you are. adjust as needed and drill your proper size hole Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now