Guest Super '54 Posted October 21, 2009 Share Posted October 21, 2009 (edited) Hi there! First post...so here we go.. My '54 is leaking from the TC so I removed inspection plate and cover. The TC is perfectly dry (outside) from the near of the front and rearwards, but wet where I guess the O-ring will be.I plan to remove the 322 to have this adressed but I'd like to know if I could get by by just replacing the O-ring or should I replace the front seal on the tranny as well? ( Leaves are fallin' and I have to work on the car outdoors...) Edited October 21, 2009 by Super '54 (see edit history) Link to comment Share on other sites More sharing options...
Bhigdog Posted October 21, 2009 Share Posted October 21, 2009 Hi there! First post...so here we go.. My '54 is leaking from the TC so I removed inspection plate and cover. The TC is perfectly dry (outside) from the near of the front and rearwards' date=' but wet where I guess the O-ring will be.I plan to remove the 322 to have this adressed but I'd like to know if I could get by by just replacing the O-ring or should I replace the front seal on the tranny as well? ( Leaves are fallin' and I have to work on the car outdoors...)[/quote']If the seal isn't leaking you could get by without changing it. Of course it might start leaking 2 weeks after you put it all back together. Or it could be the seal that's leaking now. Might as well do it right and replace the seal. I assume you made sure a drain plug isn't leaking..........Bob Link to comment Share on other sites More sharing options...
special55 Posted October 21, 2009 Share Posted October 21, 2009 When doing this repair take your time and follow the service manual.These converters have weights on them and you want to make sure you assemble it the way it came apart.If it is like my 55 you should only need to remove 3 or 4 bolts to seperate the converter from the engine flywheel. Don't make the mistake of removing them all before you have everything marked clearly.Good luck,Rich Link to comment Share on other sites More sharing options...
d2_willys Posted October 21, 2009 Share Posted October 21, 2009 You go that far, putting in the o-ring, then do the front seal too. Rule of thumb: whenever you have the transmission out of the car change the front seal (and rear main seal on engine). Then you are good to go for a long time. Link to comment Share on other sites More sharing options...
Guest Super '54 Posted October 21, 2009 Share Posted October 21, 2009 Thanx in advance! I aim to to take care of this as soon as possible, before x-mas i.e (BTW pardon for my bad/ misspelling English - all in all I'm just your friendly neighborhood Swede (or would it be neighbourhood?..nah that seems to be British English..off topic I know..misuse of capitols etc..)I'll keep you updated as I proceed anyway. Link to comment Share on other sites More sharing options...
Thriller Posted October 22, 2009 Share Posted October 22, 2009 There's a few of us here from the Commonwealth who haven't gotten lazy and started leaving letters out of words like neighbourhood ;)I'd love to hear more about that Super, perhaps even a few photos. There's also a site at 1954 BUICK | The Forum & The Website that you may want to consider visiting. Link to comment Share on other sites More sharing options...
Bhigdog Posted October 22, 2009 Share Posted October 22, 2009 Thanx in advance! I aim to to take care of this as soon as possible' date=' before x-mas i.e (BTW pardon for my bad/ misspelling English - all in all I'm just your friendly neighborhood Swede (or would it be neighbourhood?..nah that seems to be British English..off topic I know..misuse of capitols etc..)I'll keep you updated as I proceed anyway.[/quote']Your English is a Hell of lot better than our Swedish. Come to think of it, it's also better than in a lot of the posts from the U.S. Good luck with the dynaflow. It's actually a pretty easy trans to work on. BTW, do expect your trans to drip some amount of fluid no matter what you do. It's just it's nature...........Bob Link to comment Share on other sites More sharing options...
Aaron65 Posted October 22, 2009 Share Posted October 22, 2009 Have you checked to make sure that all the bolts holding the front cover of the converter on are torqued to 25 ft./lbs? I had a few loose ones that caused a massive leak...tightening them turned it into a manageable drip...just right for a Dynaflow. Link to comment Share on other sites More sharing options...
trp3141592 Posted October 22, 2009 Share Posted October 22, 2009 Here's a free supply of "u" 's for all the Brits who need them. They're all NOS or only slightly used.uuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuLOL. --Tom Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now