Narve N Posted June 16, 2019 Share Posted June 16, 2019 The oilpan of my 1940 NewYorker will not come off and I need to check the oil pick-up for free movement as the pressure drops alarmingly in turns. I have slackened all the 26 bolts and banged heavily on the pan sides with a 2x4 piece in between. Any suggestions to what might hold it, I am suspecting that the guys that were "overhauling" the engine in AZ some 15 years ago used Loctite to get it to stick to the block? Would heating everything to a certain temperature help? Link to comment Share on other sites More sharing options...
c49er Posted June 16, 2019 Share Posted June 16, 2019 They might have siliconed it on too. The pan on all the 323's come straight off...easily. Work it carefully off with a wedge type tool...wide thin screw driver etc. The oil PU float tangs are bent wrong letting the PU float ride to high for the full oil level... 1 Link to comment Share on other sites More sharing options...
Narve N Posted June 17, 2019 Author Share Posted June 17, 2019 A chisel came in handy to separate the pan from block. Someone previously had used a plenty of adhesive to mount their homemade gasket. Inside was a correct for 1940 solid mounted oil intake with no provision for floating up and down so there are no tabs to be wrongly adjusted. Is there any other way the oil screen/intake can be mounted incorrectly, allowing oil pressure to drop in turns with oil level just below full? As a remedy, can I fill an extra quart above full - or would that create other issues? Link to comment Share on other sites More sharing options...
FLYER15015 Posted June 17, 2019 Share Posted June 17, 2019 Narve, Since your oil pick up is "fixed", and your losing pressure in the turns, you could either lower the pick up a bit, or raise the oil by adding and extra quart. I would add the oil first and run a controlled test with some hard turns, while watching the pressure gage. The extra oil won't hurt a thing. No amount of extra baffling in the crank case will prevent the oil from sloshing around. Makes me wonder if she loses pressure up or down steep hills ? Because all that oil runs to the front or back of the pan. Mike in Colorado Link to comment Share on other sites More sharing options...
Spinneyhill Posted June 17, 2019 Share Posted June 17, 2019 I have to ask the dumb question. How much oil is required to bring it from empty to FULL on the dipstick, when you change the oil? Is that the amount specified in the manual? What I am getting at is whether it has the correct dipstick, as opposed to one that is too long! How far above the bottom of the oil pan is the oil pickup mounted? Link to comment Share on other sites More sharing options...
c49er Posted June 17, 2019 Share Posted June 17, 2019 (edited) 6 quarts to fill the pan to the full on the dip stick... I just fixed this same issue on a 1950 Chrysler T&C. Going around the corner with a full pan and losing oil pressure is the clue of a oil PU float set too high. Edited June 19, 2019 by c49er (see edit history) Link to comment Share on other sites More sharing options...
Narve N Posted June 18, 2019 Author Share Posted June 18, 2019 The engine is now filled with 6,5 qts of oil. I noticed that the dipstick is likely the original and quotes 6 quarts for full, however the dipstick can be in two positions when fully inserted with about 1/4" travel and 0,3 qts in between them. Likely the fully dipped stick (most optimistic) is the most correct, showing 6 qts when I had filled 6,0. With 6,5 qts the level is another 1/4" above "FULL". Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now