Summershandy Posted March 31, 2019 Share Posted March 31, 2019 I'm just in the process of replacing the carburetor gaskets on my car. I'm not a fan of sealants but have used them in other applications. I've never worked with carb gaskets. Is a sealant recommended? Guess I'm asking because the heat shield is a little pitted and maybe a thin coat could help seal it? I'm also short a couple gaskets from CPR so I have to wait for some more. Don't want to change any heights of anything as mentioned before. I also read from Charles that it's thick gasket between carb and heat shield and thin gasket between carb and intake. Mine was opposite. Does this configuration really matter? Link to comment Share on other sites More sharing options...
Bloo Posted April 1, 2019 Share Posted April 1, 2019 Indian head (but not if you ever want to get the gaskets back off). It works great on intakes, but use sparingly and don't dribble or squirt any on the inside. Frankly I am disinclined to use it on intakes anymore now that there's a bunch of alcohol in the gas. You don't want it winding up on the valvestems causing the valves to stick. I would probably use new gaskets and put them on dry. Link to comment Share on other sites More sharing options...
PONTIAC1953 Posted April 1, 2019 Share Posted April 1, 2019 hi, i had it backwards, checking the shop manual, i find pictures showing the thick one in between the manifold and heat shield, thin one in between the carburetor and heat shield. Link to comment Share on other sites More sharing options...
PONTIAC1953 Posted April 1, 2019 Share Posted April 1, 2019 on coating the gaskets, i would use non silicone type like copper coat. Link to comment Share on other sites More sharing options...
carbking Posted April 1, 2019 Share Posted April 1, 2019 As a general rule, using gasket sealant on carburetor gaskets.......................means an EXPENSIVE carburetor rebuild is just around the next corner. Kind of like using Teflon tape. No longer rebuilding carburetors, but when we were doing so; a unit that came in with gasket sealer normally cost two to three times to rebuild if the P.O. had assembled dry. Often, once the sealer was detected, we would just send it back to the owner and suggest they find a different carb to rebuild. Jon. Link to comment Share on other sites More sharing options...
Summershandy Posted April 1, 2019 Author Share Posted April 1, 2019 Thanks for your thoughts guys. I am very aware of the consequences of sealant like silicone when it comes to a carb. This is why I needed some feedback like this. Think I'm staying away from sealants. Would a thin film of vaseline on the gasket side that contacts the lightly pitted heat shield be of any help? Another observation was the old gasket was saturated. It is after all, 65 years old. I think I read it finally does get wet over time. The thicker gasket was also held together with a staple at each end with it's original GM part number stamped in. Link to comment Share on other sites More sharing options...
carbking Posted April 1, 2019 Share Posted April 1, 2019 7 hours ago, Summershandy said: Thanks for your thoughts guys. I am very aware of the consequences of sealant like silicone when it comes to a carb. This is why I needed some feedback like this. Think I'm staying away from sealants. Would a thin film of vaseline on the gasket side that contacts the lightly pitted heat shield be of any help? Another observation was the old gasket was saturated. It is after all, 65 years old. I think I read it finally does get wet over time. The thicker gasket was also held together with a staple at each end with it's original GM part number stamped in. At what temperature does vaseline melt, and does your exhaust exceed that temperature????? Jon. Link to comment Share on other sites More sharing options...
Summershandy Posted April 1, 2019 Author Share Posted April 1, 2019 (edited) 1 hour ago, carbking said: At what temperature does vaseline melt, and does your exhaust exceed that temperature????? Vaseline melts between 100 degrees - 130 degrees so I guess your answer is yes. I'm not saying I'm going to use it but the vaseline wouldn't be in contact with the exhaust. The layers from the intake are 5 paper gaskets, heat shield, 3 paper gaskets then carb. The "sealant" would be between the 3 paper gaskets and heat shield just under the carb. But I'm sure it would melt anyway, things get pretty toasty under the hood. Thanks for that fact of the day.....I now know when vaseline melts! Edited April 1, 2019 by Summershandy spelling (see edit history) Link to comment Share on other sites More sharing options...
Bloo Posted April 2, 2019 Share Posted April 2, 2019 I just want to clarify that when I half-heartedly suggested Indian Head, I was referring to flange gaskets and heat shields and so on, and then only if the surfaces or the gaskets are questionable. I did NOT mean the gaskets in the carburetor itself. Those are ALWAYS dry. If they wont seal dry, straighten whatever is warped! Link to comment Share on other sites More sharing options...
Summershandy Posted April 2, 2019 Author Share Posted April 2, 2019 For sure Bloo, flanged surfaces only. I've used Indian Head sealant for a quite permanent seal for like a cork crank seal. When I rebuilt my carb I didn't use any sealants. I don't really see why one would want to....I've taken my carb apart more times than I could count for inspection and would have never been able to done so with so called "adhesives". Thanks for the clarification. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now