[Removing Guide Pins on Bottom Bellhousing]

I need to remove the guide pins on Bottom of 27 Standard bellhousing. The ones that match bottom half of bellhousing. I did a stupid thing, I forgot to put bottom bellhousing on, now I have trans and rear end all bolted up. Do these pins screw in or driven in?? Should I just try to drill out and get new pins?

Thanks

[27 Ignition switch lever]

I'm looking for a Ignition switch lever for my 27 Buick woodie. IThe lever has a hole that a cotter pin holds it on. thanks

[Valve push rods don't turn on my 27]

BEN,

I finally just figured that out. With the spring holding push rods down I can see why they won't turn. I did have engine completely rebuilt. New 030 pistons, all rods babbitted, and crank checked and balanced. Thanks for your Help,

Steve

[Heat Riser Sleeves]

I'm also looking for one. I think i saw it in BOB'S

[Valve push rods don't turn on my 27]

Rebuilding my 27 Buick Standard. I notice after putting everything together the valve push rods don't turn when the pressure is off them. Are they suppose to turn or not??. I just check my 26 standard and only one would turn. I took rocker arms assem off and lossen the nut that hold the cage between the valve push rods and rods would turn. once I tighten them up they wouldn't turn.

Also engine turns over very hard with crank. It turned over easier when I put 3/4" rachet on crank shaftnut before putting hand crank adapter on. Is this normal?? Thanks for any help.

[Stewart Warner fuel gauge D-300B]

Does anyone have an older Stewart Warner Catalog that could look up a fuel gauge part number D-300B. I'm trying to figure out if it is 6 volt and the ohms. Thanks

[Stewart Warner Gas Gauge D-300B??]

I'm trying to find out if a Stewart Warner gas gauge Model D-300B is 6 volt and what the ohm's are? This is an old stock gauge and the factory don't have books that list that number. Also of coarse the local dealers have thrown their old books out. Thanks for any Help

[Inner axle nut for 27 Buick Standard]

I'm looking for an inner axle nut for a 1927 Buick Standard. Threads are 3/4x16", takes wrench size of 1 1/4" and height is about .45" This is a sloted nut.. My threads wre stripped on mine. This is called a heavy castle nut. Thanks for any help.

[Runningboard trim for a 1927]

I called Bob's Automobilia today and was told they can't get the runninboard trim for my 27 Buick. Has anyone used another supplier?? I found some at Restoration Supply Company but don't know which one would be correct. thanks for any help.

[27 Door Post wood pattern]

Does anyone have a pattern for the front door posts for a 1927 Buick Model 27? Mine are all rotted out and not enough to make a pattern. Thanks for any help.

[Heat control knob and plate for 27 Buick Standard.]

I'm looking for the heat control knob and plate for my 27 Buick standard. I do have the choke knob.

thanks

[Ok, What gets chromed?]

I have a 26 and 27 Buick. When I took all the parts to be nickeled, the palter said do it in chrome as will last alot longer. I'm not a purest and think the chrome lasts longer. Never have and never intend on having them judged. I do my cars my way.

[Country Classic Cars]

We stopped in while traveling Route 66. Only found a couple cars that where decent. Most have new paint right over the bondo and sand marks. Waste of time going there. About same quality as Golden-Rod garge up here in Freeport, ME WASTE OF TIME

[Vintage Reproduction Parts ???]

Has anyone bought from Vintage Reproduction Parts in Australia? I'm looking at parts for my 27 Buick Woodie, Hubcaps and windshield crank handle. Would anyone else have these parts? Thanks

[Vintage Reproductions???]

Has anyone bought from Vintage Reproductions in Australia?? I was looking at parts for my 27 Buick woodie, Hubcaps and windshield crank. would anyone ese have these parts? Thanks

[6 volt gas gauge with chrome rim]

I'm looking for a 6 volt round gas gauge with a chrome rim. I need it for my 27 Buick. I plan on using a 6 volt Jeep sending unit with it. thanks

[Delco 640K Distributer???]

I bought a Delco 640K 46991 Distributor for my 27 but doesn't fit. Does anyone know what this would fit?? Thanks

[27 Standard front wheel seals]

i'm looking for the front wheel grease seals on my 27 Standard. I need 2 of the metal holder. Could also use the felts. thanks

[WTB: outside visor for 26/27 coupe]

I have a 26-27 Buick that was restored 35 years ago by a friend of mine. He had a new visor made at a local sheet metal shop. I have never had it covered but it is an exact copy of the orginial. I was at LeBarron Bonney a couple of week ago and they can make a cover for it. good luck.

[New pistons 1930 40 series?]

I just had pistond made for my 27 standard by Arias in CA. Very pricey $1150 for 6 but I needed .30 oversize. They have nice pistons, used them in my 26 two years ago. Good Luck

[Windup winshield handle on 1927]

How do you remove the windup windshield handle on a 27 standard?. My 26 has a scew in middle of handle. The 27 doesn't, it hasn't been used since 1942.

Thanks

[Rear Wheel Roller Bearings 27 standard]

How much end play should there be in the rear wheel roller bearings on a 27 Standard? Mine seem to move in and out quite a bite. Does it need more spacers and where to buy the spacers? Thanks

[Four 48 Ford Fenders For sale]

4 fenders from 48 Ford Conv. Left rear rust free, Other 3 have small rust bottom fenders. Includes front inner fenders. Can e-mail pictures. $400 plus shipping

[26 Buick headlight rims and lenses]

A friend of mine is looking for headlight lenses and rims for his 26 Buick. Thanks

[1927 Standard rear wheel bearings]

The rear roller bearings seem to move in and out. Should there be any play? Also where can I find the inner washer as one was missing? Thanks