Guest Posted June 26, 2003 Share Posted June 26, 2003 I need to remove the front shock absorbers for rebuilding on my '53 Roadmaster. I have never done this before, and would appreciate any advice on how to do it. Do I need any special tools, such as a spring compressor (which I do not have)? Does the car need to be in the air or sitting with its weight on the spring?I'm planning to drive this car to Flint next month, and this is just about the last step to make it roadworthy. Thanks in advance for any help.Pete Phillips, BCA #7338Ector, Texas Link to comment Share on other sites More sharing options...
Guest Posted June 26, 2003 Share Posted June 26, 2003 just use a floor jack. raise the car by the hub to compress the spring. remove the three bolts from the top of the shock, which you can see front under the hood.then remove the eccentric bolt at the top of the a-arm. to do this, remove the grease caps, and stick an Alan wrench down the hole of the a-arm, and crank the eccentric bolt out. this will free the whole shock. leave the car on the jack, so you don't dislodge the spring. Link to comment Share on other sites More sharing options...
Guest 53and61 Posted June 26, 2003 Share Posted June 26, 2003 If memory serves, one of the bolts is in the middle of the spring and points upward into the body of the shock. You get to it from the bottom with a long extension up through the spring. Link to comment Share on other sites More sharing options...
Charles2 Posted June 26, 2003 Share Posted June 26, 2003 You will also have to have the wheel alignment checked when you are done. Replacing the front lever shocks, which also serve as the upper suspension A-frames will change the camber and caster unless you are really lucky. And, even then, you wouldn't know you were lucky without checking alignment. There has been considerable discussion on this forum about someone wanting to get the alignment checked on a '53 and how his local Buick dealer wouldn't take the job. You might want to read the story and the responses. Good luck. Link to comment Share on other sites More sharing options...
Bill Stoneberg Posted June 26, 2003 Share Posted June 26, 2003 Pete,I can help you with this manana... Its fairly easy. Link to comment Share on other sites More sharing options...
palbuick Posted June 27, 2003 Share Posted June 27, 2003 Be one the safe side, rent or borrow a spring compressor. You wil have to locate a compressor that fits inside of the spring, the new ones compress the spring on the outside and will not work. First remove the bolt from the center of the shock from inside the spring. Then compress the spring, if you have a hydraulic jack under the lower A arm, let the jack down slowly and the spring will fall out, no chance of it flying around and breaking something especially you.Good luckJIm Schilf / palbuick@aol.com Link to comment Share on other sites More sharing options...
Guest Teamsterdug Posted June 27, 2003 Share Posted June 27, 2003 Lets not forget one very important thing...we are assuming that the engine is still in the car??? The weight of the engine makes it a lot easier to accomplish by offering apposing weight when jacking from underneath. Link to comment Share on other sites More sharing options...
Bill Stoneberg Posted June 27, 2003 Share Posted June 27, 2003 You cant do it without the engine in the car... I have tried and tried. Link to comment Share on other sites More sharing options...
Guest Posted June 27, 2003 Share Posted June 27, 2003 I think it's funny how all of us internet mechanics love to give free advise from our key boards without getting our hands dirty! <img src="http://www.aaca.org/ubbthreads/images/graemlins/smile.gif" alt="" />we are "virtual auto restorers".we sit on our asses and read about the car getting finished!I think I like it...! <img src="http://www.aaca.org/ubbthreads/images/graemlins/smile.gif" alt="" /> <img src="http://www.aaca.org/ubbthreads/images/graemlins/smile.gif" alt="" /> Link to comment Share on other sites More sharing options...
Bill Stoneberg Posted July 3, 2003 Share Posted July 3, 2003 Tommy,You are mistaken in this case.Last Friday I went to Pete's garage and got my hands dirty showing him how to take the shock off.I like to work on the cars and am more then willing to get in and work. Link to comment Share on other sites More sharing options...
TomE_1953 Posted July 7, 2003 Share Posted July 7, 2003 WOW! 'Great Minds' think alike! I had 'new' 1953 Lever-Action Shocks on my 1953 Roadmaster with the help of Don Holdmeyer from the KC BCA Chapter. He is restoring TWO 1953s and am I --LUCKY-- to have him in Kansas City! I watched and learned from removal to installation. It is NOT easy as a previous post stated and if that spring lets loose you can forget "Flint" ('widow-maker' if you catch my drift).I want to take this time to thank RALPH CRISP (BCA) of Omaha who gave me a GREAT deal on the shocks! They looked like NOS when I opened the box! You all can talk to him at the Swap Meet in Flint.Best thing I ever did was join the BCA and KC BCA Chapter when I got this car!The members share their knowledge and pitch in to help and I can't say enough about you all!!! I want to gain as much knowledge so I can pass it on when my time comes."ANNIE" is itching to hit the road and head North to Flint! <img src="http://www.aaca.org/ubbthreads/images/graemlins/laugh.gif" alt="" /> Link to comment Share on other sites More sharing options...
442w30 Posted August 5, 2022 Share Posted August 5, 2022 Hi,how do I remove the lever action rear shocks on my 1953 Buick Special 2 door hard top? Link to comment Share on other sites More sharing options...
g-g-g0 Posted August 7, 2022 Share Posted August 7, 2022 What is the purpose of removing? If they are “soft” add some light oil like motorcycle fork oil to them. Work them up and down a time or two and check oil level and add more oil if necessary. Can’t remember exactly the steps to actually remove the shock. First I would remove the linkage from the arm. Then the shock body unbolts to the frame. Writing from memory but believe this should be close to procedure for removal. Gary 1 Link to comment Share on other sites More sharing options...
Rusty Heaps Posted August 9, 2022 Share Posted August 9, 2022 Unless the seals are done in. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now