scott12180 Posted April 27, 2007 Share Posted April 27, 2007 What is a good modern spark plug that I can use on a 1932 Standard Eight Packard?References I have call for original equipment A-C type K-9 or K-7. This nomenclature is not currently available. Any recommendations on modern equivalent?--Scott Link to comment Share on other sites More sharing options...
Owen_Dyneto Posted April 27, 2007 Share Posted April 27, 2007 Assuming your car still has the original cylinder head (31 and earlier used either 18mm or 7/8 thread size), Autolite recommends a 308, I've used these for years in nearly all the Packard Eights with 14mm plugs. If you're using the original high tension wires ending in the eyelets and fastened with knurled thumbnuts, use a 303 which I believe still comes with a threaded top post, the knurled thumbscrews are readily available. Link to comment Share on other sites More sharing options...
mlander Posted April 27, 2007 Share Posted April 27, 2007 According to my old sparkplug chart AC K series sparkplug is a 14mm by 3/8? reach and is in the middle of the sparkplug heat range. K14 being at the hottest part of the range and K-5 being at the coolest part of the heat range the others being K-5, K-7, K-9, K-10, K-11, K-12 and K-14. These sparkplugs were used in many GM and others engines until the change was made by AC to the newer and still used AC 4 series which merely means that it is a 14mm and no ?R? means no resistor. A #5 after the number ?4? means it is the #5 heat range. AC 414 means it is a 14 mm by # 14 heat range.AC SPARKPLUG SPECIFICATION CHARTPASSENGER CARS-1926-1942PACKARD ONLYThru 1929-Turbo Head.....781930 Turbo Head.............86All thru 1931-Reg. Head...78S1932..............................461933-34-35-36................451937-38.........................103S1939-40-41-42...............106Yours, M.L. Anderson Link to comment Share on other sites More sharing options...
Tom M Posted April 27, 2007 Share Posted April 27, 2007 <div class="ubbcode-block"><div class="ubbcode-header">Quote:</div><div class="ubbcode-body">All thru 1931-Reg. Head...78S</div></div> Would this be a 18mm or 7/8 thread size?I asked because that is the size I have in my car and was running Champions.Thanks Link to comment Share on other sites More sharing options...
tbirdman Posted April 27, 2007 Share Posted April 27, 2007 This is timely. Last night I decided to remove the spark plug wire holder and repaint it. Doing some research, I found that I had incorrect clip on wires. I'm running AC 45s in my car with the clip on wires. This morning I ordered AC's with the correct threaded top and knurled knobs from Bruce Blevins 810-744-1820 (Michigan). I bought a set of plug wires with the correct eyelet on the end from Cole Ignition 585-342-9613(New York). Amazing what a simple project can morph into <img src="http://forums.aaca.org/images/graemlins/tongue.gif" alt="" />I actually have a NOS set of the original AC K7s that were spec in the car. I haven't decided to put them into the car yet. Link to comment Share on other sites More sharing options...
Tom M Posted April 27, 2007 Share Posted April 27, 2007 Ken,Does Bruce Blevins Advertise in the The Packard Cormorant Magazine? Link to comment Share on other sites More sharing options...
tbirdman Posted April 27, 2007 Share Posted April 27, 2007 <div class="ubbcode-block"><div class="ubbcode-header">Quote:</div><div class="ubbcode-body">Ken,Does Bruce Blevins Advertise in the The Packard Cormorant Magazine? </div></div>Yes! Link to comment Share on other sites More sharing options...
Tom M Posted April 27, 2007 Share Posted April 27, 2007 Can you let us know how the parts look once you receive them? Link to comment Share on other sites More sharing options...
tbirdman Posted April 27, 2007 Share Posted April 27, 2007 <div class="ubbcode-block"><div class="ubbcode-header">Quote:</div><div class="ubbcode-body">Can you let us know how the parts look once you receive them? </div></div>Will do. Link to comment Share on other sites More sharing options...
mlander Posted April 27, 2007 Share Posted April 27, 2007 Thru 1929-Turbo Head.....78 (7's are 7/8")1930 Turbo Head.............86 (8's are 18mm)All thru 1931-Reg. Head...78S1932..............................46 (4's are 14mm)1933-34-35-36................451937-38.........................103S (1's are 10mm)1939-40-41-42...............106Somewhere on the Internet is an AC explanation chart but I have lost it's address.M.L. Anderson Link to comment Share on other sites More sharing options...
Restorer32 Posted April 27, 2007 Share Posted April 27, 2007 What is a "Turbo head"? Link to comment Share on other sites More sharing options...
mlander Posted April 28, 2007 Share Posted April 28, 2007 What is a "Turbo head"? The sheet that I have packed away in the event that I move (???) is not quickly available at this time and I don't believe that it had any expanation about this item. My guess would be that it was a cylinder head with squish and quench configuration as this was being used at this time. However this is a guess!!!Yours, M.L. Anderson J Link to comment Share on other sites More sharing options...
tbirdman Posted May 1, 2007 Share Posted May 1, 2007 <div class="ubbcode-block"><div class="ubbcode-header">Quote:</div><div class="ubbcode-body">Can you let us know how the parts look once you receive them? </div></div>Received the spark plugs and knurled knobs. They look great. Link to comment Share on other sites More sharing options...
tbirdman Posted May 12, 2007 Share Posted May 12, 2007 <div class="ubbcode-block"><div class="ubbcode-header">Quote:</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Quote:</div><div class="ubbcode-body">Can you let us know how the parts look once you receive them? </div></div>Received the spark plugs and knurled knobs. They look great. </div></div>I received the spark plug wires from Cole Ignition. Look good with what I assume is the correct ends and wire finish...shiny black. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now